JCB · Engine ECU (Dieselmax / Ecomax) - electrical
JCB Fault Code P0685
ECU power relay control circuit open
What does JCB code P0685 mean?
The relay that powers the engine ECU is not being controlled properly, so ECU power may drop out. Urgency: check soon - the machine may derate or limit a function. Check first: swap the relay with a known good one of the same type.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Swap the relay with a known good one of the same type
Then 5 more checksWhere this code shows
Switch the key on and note any warning lamp or fault icon on the cluster.
Checks
0 of 6 done
Causes
- ECU main power relay failed, or its contacts burnt
- Relay control wire open between the ECU and the relay
- Corroded relay socket or loose terminals
- Blown fuse in the ECU supply
1 more causeFewer causes
- Poor battery or earth connection to the relay
How it failed
You'll notice: The ECU may lose power as soon as the key is on, or cut out unexpectedly while running.
Open circuitRead from how the source describes the code
No current flows, or the signal floats - a wire, pin or coil is broken.
- Meter test
- Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
- Good result
- Near 0 Ω on each wire. The part reads its listed resistance, not OL.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: ECU power relay, 5 V supply, injector power supply and starter circuit
1 other code on this part is also open circuit (P20EA-72). When they show together, start at the wiring and connector they share.
- P0616Starter relay circuit lowOtherCheck soon
- P0617Starter relay circuit highOtherCheck soon
- P0641ECU 5 V sensor supply 1 faultOtherCheck soon
- P0651ECU 5 V sensor supply 2 faultOtherCheck soon
- P0685ECU power relay control circuit openOpen circuitCheck soon
- P0687Main relay system fault (closed)OtherCheck soon
- P0697ECU 5 V sensor supply 3 faultOtherCheck soon
- P1261Cylinder 1 fuel injector circuit malfunctionOtherCheck soon
- P1262Charge circuit fault on bank 2OtherCheck soon
Show the other 17 codesHide the other codes
- P06A7-00Sensor supply monitoring error through DCUOtherCheck soon
- P20EB-71DCU relay stuckErratic or implausibleCheck soon
- P20EA-72DCU relay opens earlyOpen circuitCheck soon
- P062BControl module fuel injector control performanceErratic or implausibleCheck soon
- P062DInjector bank 0 shorted to groundShorted lowStop now
- P062EInjector bank 1 shorted to groundShorted lowStop now
- P0612Fuel injector control module relay control faultOtherCheck soon
- P0615Starter relay circuit faultOtherCheck soon
- P1602Starter relay control circuit global faultOtherCheck soon
- P16555 V power supply 4 voltage faultOtherCheck soon
- P2146Injector supply voltage faultOtherCheck soon
- P2147Injector voltage source cutoff malfunctionOtherCheck soon
- P2148Injector voltage source cutoff malfunction (bank 2)OtherCheck soon
- P2149Injection nozzle common 2 drive system faultOtherCheck soon
- P3300Starter motor engagement protection faultOtherCheck soon
- P3301Starter motor overheat protection activatedReal conditionCheck soon
- P3302Starter motor overrun protection faultOtherCheck soon
Other JCB codes: Engine ECU (Dieselmax / Ecomax) - electrical
Related on Equipments Finder
Source
Partao JCB fault code P0685 page
This source lists P0685 and its meaning. The guidance on this page is general, not taken from it.
The source covers: 2CX, 3CX, 4CX, 214-217, 526, 533-105, 540, TM320, Fastrac.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
