JCB · Engine ECU (Dieselmax / Ecomax) - temperature sensors
JCB Fault Code P0117
Coolant temperature sensor signal low
What does JCB code P0117 mean?
The voltage from the coolant sensor is too low, which reads as an impossibly hot engine, usually a short to ground. Urgency: check soon - the machine may derate or limit a function. Check first: with key on, read the live temperature and check it reads an impossibly high value.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
With key on, read the live temperature and check it reads an impossibly high value
Then 5 more checksWhere this code shows
Switch the key on and note any warning lamp or fault icon on the cluster.
Checks
0 of 6 done
Causes
- Signal wire shorted to ground
- Coolant temperature sensor shorted internally
- Water in the connector bridging the signal pin to ground
- Harness rubbed through against the engine or a bracket
1 more causeFewer causes
- Damaged ECU input, which is rare
How it failed
You'll notice: The ECU thinks the engine is extremely hot, so the cooling fans may run flat out, the temperature gauge may swing high and the engine may derate even though the coolant is normal.
Shorted lowRead from how the source describes the code
The signal sits at or near zero volts - less than a working sensor can send.
- Meter test
- Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
- Good result
- Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
When to stop
Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Fuel, oil and coolant temperature sensors and engine overheating
- P0115Coolant temperature sensor 1 circuit faultOtherCheck soon
- P0116Coolant temperature sensor range/performanceErratic or implausibleCheck soon
- P0117Coolant temperature sensor signal lowShorted lowCheck soon
- P0118Coolant temperature sensor signal highOpen circuitCheck soon
- P0180Fuel temperature sensor A circuit faultErratic or implausibleCheck soon
- P0181Fuel temperature sensor faultErratic or implausibleCheck soon
- P0181-87Missing fuel temperature CAN messageLost messageCheck soon
- P0182Fuel temperature sensor A signal lowOtherCheck soon
- P0183Fuel temperature sensor A signal highShorted highCheck soon
Show the other 9 codesHide the other codes
- P0195Oil temperature sensor external voltage faultOtherCheck soon
- P0196Oil temperature sensor signal gradient faultLost messageCheck soon
- P0196-87Missing oil temperature CAN message from engine ECULost messageCheck soon
- P0197Oil temperature sensor signal lowOtherCheck soon
- P0198Oil temperature sensor signal highShorted highCheck soon
- P0217Coolant temperature above limit (overheating)Shorted highStop now
- C1021Engine coolant level lowOtherCheck soon
- B1543Critical high coolant temperatureLost messageStop now
- B1546Coolant temperature high (operator level)OtherCheck soon
Other JCB codes: Engine ECU (Dieselmax / Ecomax) - temperature sensors
Related on Equipments Finder
Source
Partao JCB fault code P0117 page
This source lists P0117 and its meaning. The guidance on this page is general, not taken from it.
The source covers: 2CX-5CX, Loadall, tracked excavators, wheeled loaders, site dumpers, rough terrain forklifts, EcoMax 444.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
