EF Logo

JCB · Engine ECU (Dieselmax / Ecomax) - speed sensors

JCB Engine speed and timing sensors, oil pressure and oil level fault codes

The crankshaft sensor reads a toothed wheel on the crank and the camshaft sensor reads the cam, together giving the ECU engine speed and position. A knock sensor or accelerometer listens for engine vibration.

More about these parts

Without the speed signals the ECU cannot time the injectors. The oil pressure sensor or switch tells the ECU and cluster whether the engine has enough oil pressure. Low pressure can ruin the engine quickly.

FaultCheckP0016JCB · Engine speed and timing sensors, oil pressure and oil level
Code shows hereFAULTP0016

Where this code shows

Switch the key on and note any warning lamp or fault icon on the cluster.

What do these codes mean?

JCB codes P0016 to P0523 are all about the engine speed and timing sensors, oil pressure and oil level. The most common failure type is lost message (4 of 15); 3 need an immediate stop. Start with this check: check the sensor air gap and the condition of the toothed wheel.

How urgent are they?

3 of 15 codes here mean stop now; 11 can wait until the shift ends, but find the cause before the next one; 1 is information only.

  • Stop now3
  • Check soon11
  • Info1

What should I check first?

Check the sensor air gap and the condition of the toothed wheel

Shared checks

15 of 15

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • JCB P0016Crank and cam position correlation fault

    The ECU sees the crank and cam signals out of step.· Other
    Check soon

    Causes

    • Timing gear train jumped a tooth or worn so cam and crank are out of step
    • Loose or damaged crank or cam trigger wheel
    • Worn or damaged timing chain or gear drive
    • Wrong sensor fitted after repair, or a sensor not seated
    • Wiring crossed or damaged between the sensors and the ECU

    Checks

    1. 1Compare crank and cam signals live and see if the offset changes with speed
    2. 2Check the timing marks or locking positions for the gear train
    3. 3Inspect the trigger wheels for looseness, wear or damage
    4. 4Confirm each sensor is correctly seated and the connector is on its own sensor
    5. 5Check the wiring for damaged insulation between both sensors and the ECU
    6. 6Run a compression test only if timing is suspected to have shifted
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P250BEngine oil level low at key-on

    The engine oil level sensor reported a low level when the key was switched on, or its circuit has a range problem.· Lost message
    Check soon

    Causes

    • Engine oil level really low from a leak or oil use
    • Oil level sensor failed or fouled with sludge
    • Wiring or connector fault at the sensor
    • Machine parked on a slope giving a false level

    Checks

    1. 1Check the engine oil level on the dipstick on level ground
    2. 2Look for oil leaks under the engine and around the sump
    3. 3Check the sensor connector and wiring for corrosion and chafing
    4. 4Compare the sensor reading on live data with the dipstick level
    5. 5Replace the sensor only when the dipstick level is correct and the signal is still low
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • JCB P0325Accelerometer fault (signal to noise ratio too low at idle)

    Accelerometer fault (signal to noise ratio too low at idle).· Real condition
    Check soon

    Causes

    • Accelerometer signal pulled low by a short to ground or an open supply
    • Sensor or part failed giving a low reading

    Checks

    1. 1Read the accelerometer value on live data and compare it with the expected value
    2. 2Unplug the accelerometer and check the signal wire for a short to ground and the supply for 5 V
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • JCB P0330Knock sensor 1 circuit fault

    Knock sensor 1 circuit fault.· Other
    Check soon

    Causes

    • Knock sensor 1 circuit or its wiring faulty
    • Connector corrosion or a loose pin

    Checks

    1. 1Read the live data for the knock sensor 1 circuit and look for a value that is stuck or implausible
    2. 2Check the knock sensor 1 circuit connector and wiring for damage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P0335Crankshaft position sensor circuit fault

    The ECU is not getting a valid crankshaft signal.· Lost message
    Stop now

    Causes

    • Crankshaft speed sensor failed or its signal weak
    • Damaged or loose sensor connector, or a broken wire to the ECU
    • Metal debris or oil sludge on the sensor tip
    • Sensor air gap changed because it is loose in the housing
    • Damaged or missing teeth on the crank trigger wheel

    Checks

    1. 1Look at the live engine speed in the diagnostic tool while cranking and confirm a reading appears
    2. 2Inspect the sensor tip for metal swarf and the wheel for damaged teeth
    3. 3Check the sensor mounting bolt is tight and the sensor sits fully home
    4. 4Check the harness for chafing and the connector for backed-out pins
    5. 5Measure the sensor resistance and compare it with a known good sensor
    6. 6Check the shielded signal wire is continuous and not touching an ignition feed
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • JCB P0336Crankshaft sensor signal fault

    The ECU sees a crankshaft speed signal that is present but implausible, with noise or missing pulses.· Lost message
    Stop now

    Causes

    • Electrical noise on the crankshaft sensor wire from a poor ground or a damaged shield
    • Sensor mounted loosely so the signal drops out when the engine vibrates
    • Cracked or distorted crank trigger wheel causing irregular pulses

    Checks

    1. 1Log engine speed live and watch for dropouts, spikes or a signal that goes missing
    2. 2Check the sensor mounting and torque and look for signs it has been rubbing the wheel
    3. 3Inspect the crank wheel for cracks, missing teeth or sludge
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • JCB P0340Camshaft position sensor circuit fault

    The ECU gets no valid camshaft signal.· Lost message
    Check soon

    Causes

    • Camshaft position sensor failed or its signal weak
    • Broken wire or loose pin in the cam sensor connector
    • Sensor tip dirty or oil contaminated
    • Camshaft or cam gear damaged so the trigger signal is wrong
    • Cam sensor harness damaged near the front of the engine

    Checks

    1. 1Crank the engine and look at the live cam signal in the diagnostic tool
    2. 2Remove the sensor and inspect the tip for contamination or damage
    3. 3Check the connector, then check continuity of all three wires to the ECU
    4. 4Measure the sensor supply and ground at the plug with the key on
    5. 5Look at the cam gear or trigger wheel for wear or a missing tooth
    6. 6Replace the sensor only after the wiring and trigger wheel have checked out
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • JCB P0341Camshaft position sensor A range/performance

    Camshaft position sensor A range/performance.· Erratic or implausible
    Check soon

    Causes

    • Camshaft position sensor A range/performance drifting or worn so it no longer matches the real condition
    • Poor connection or high resistance in the camshaft position sensor A range/performance circuit
    • A related fault elsewhere making this reading look wrong

    Checks

    1. 1Compare the camshaft position sensor A range/performance value on live data with a known good value or a reference gauge
    2. 2Check the camshaft position sensor A range/performance connector and wiring for high resistance and intermittent contact
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • JCB P0371Excessive pulses on crankshaft sensor signal A

    Excessive pulses on crankshaft sensor signal A.· Other
    Check soon

    Causes

    • Excessive pulses on crankshaft sensor signal A signal pulled high by a short to the 5 V reference or supply
    • Sensor or part failed giving a high reading

    Checks

    1. 1Read the excessive pulses on crankshaft sensor signal A value on live data and compare it with the expected value
    2. 2Unplug the excessive pulses on crankshaft sensor signal A and check the signal wire for a short to 5 V or battery
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P0372Too few pulses on crankshaft sensor signal A

    Too few pulses on crankshaft sensor signal A.· Other
    Check soon

    Causes

    • Too few pulses on crankshaft sensor signal A or its wiring faulty
    • Connector corrosion or a loose pin

    Checks

    1. 1Read the live data for the too few pulses on crankshaft sensor signal A and look for a value that is stuck or implausible
    2. 2Check the too few pulses on crankshaft sensor signal A connector and wiring for damage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P0374No pulses on crankshaft sensor signal A

    No pulses on crankshaft sensor signal A.· Open circuit
    Check soon

    Causes

    • Open wire or pushed-back pin between the controller and the no pulses on crankshaft sensor signal A
    • No pulses on crankshaft sensor signal A coil, element or sensor internally open

    Checks

    1. 1Unplug the no pulses on crankshaft sensor signal A and measure across its pins, an open reading means the part is faulty
    2. 2Check continuity of each wire from the no pulses on crankshaft sensor signal A plug to the controller pin
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • JCB P0520Low oil pressure warning lamp control circuit fault

    Low oil pressure warning lamp control circuit fault.· Other
    Info

    Causes

    • The underlying fault behind this step is still present
    • The fault was repaired but the stored status has not been cleared yet

    Checks

    1. 1Read the other active codes first, this status follows from them
    2. 2After repair, clear the codes and run the machine to confirm the status does not return
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P0521Engine oil pressure sensor or switch range/performance

    Engine oil pressure sensor or switch range/performance.· Erratic or implausible
    Check soon

    Causes

    • Engine oil pressure sensor or switch range/performance drifting or worn so it no longer matches the real condition
    • Poor connection or high resistance in the engine oil pressure sensor or switch range/performance circuit
    • A related fault elsewhere making this reading look wrong

    Checks

    1. 1Compare the engine oil pressure sensor or switch range/performance value on live data with a known good value or a reference gauge
    2. 2Check the engine oil pressure sensor or switch range/performance connector and wiring for high resistance and intermittent contact
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • JCB P0522High oil pressure

    High oil pressure.· Other
    Check soon

    Causes

    • High oil pressure signal pulled high by a short to the 5 V reference or supply
    • Sensor or part failed giving a high reading

    Checks

    1. 1Read the high oil pressure value on live data and compare it with the expected value
    2. 2Unplug the high oil pressure and check the signal wire for a short to 5 V or battery
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P0523Low oil pressure

    The ECU sees low oil pressure while running, or a high voltage in the sensor circuit.· Shorted high
    Stop now

    Causes

    • Low engine oil level or diluted oil
    • Worn engine bearings or a weak oil pump giving real low pressure
    • Oil filter or oil cooler restricted
    • Oil pressure sender failed or its signal shorted high
    • Wiring fault or loose connector at the oil pressure sender

    Checks

    1. 1Stop the engine and check the oil level on the dipstick and look at the oil condition
    2. 2Check pressure with a mechanical gauge at the sender port and compare it with the ECU reading
    3. 3Check the oil filter was changed and is the right one for the engine
    4. 4Inspect the sender connector and the wires for damage or corrosion
    5. 5Read the sender signal live and see if it follows real pressure when revved
    6. 6Do not run the engine with confirmed low pressure until the cause is found
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

Shared checks

Checks, in order

  1. 1Check the sensor air gap and the condition of the toothed wheel
  2. 2Check the engine oil level and condition (on the oil pressure sensor and switch, with the diagnostic tool and a multimeter)
  3. 3Compare the crank and cam signals on live data while cranking
  4. 4Test oil pressure with a mechanical gauge to see whether the sensor is right
  5. 5Measure the sensor resistance or signal at the plug as the manual specifies
  6. 6Check the sensor, switch and wiring when the gauge pressure is normal
  7. 7Wiggle the harness while watching engine speed on live data

Causes

  • Sensor failed or air gap wrong
  • Low oil level or wrong oil
  • Reluctor wheel or timing gear damaged or dirty
  • Worn oil pump or bearings

Most common here: lost message (4 of 15)

Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

When to stop

You'll notice: The engine may crank and not start, stall, run on one signal only or run rough, and a check lamp is on.

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.