EF Logo

J1939 · Lubrication

SPN 98 Fault Code

Engine oil level

What does SPN 98 mean?

Sump oil level reported by the oil level sensor. The ECM uses it for low-oil warnings and engine protection. How urgent it is depends on the FMI after SPN 98 - pick it below. Check first: park the machine level, wait for the oil to drain back and check the dipstick.

FaultActiveSPN 98FMI --J1939 engine ECU
SPN 98
Engine oil level
FMI ?
How it failed - the number after the SPN

Can I keep running with it?

Depends on the FMI

How urgent it is depends on the FMI after SPN 98 - pick it below.

What should I check first?

Park the machine level, wait for the oil to drain back and check the dipstick

Then 4 more checks
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect a J1939-capable scan tool to the 9-pin diagnostic port.

Which FMI shows after SPN 98?

You'll notice: The oil level reading or warning is wrong.

Find the number shown after SPN 98 on your display.

  • 0SPN 98 FMI 0: Oil level is reported too highReal conditionDetroit DD15, Detroit DD13
  • 1SPN 98 FMI 1: Oil level is far too low, or above normal, depending on how the engine maker lists itReal conditionDetroit DD15, Detroit DD13, Mack MP8, Mack MP7 and 2 more
  • 2SPN 98 FMI 2: Oil level reads too low or the readings disagree and are not believableErratic or implausiblePACCAR MX-13
  • 3SPN 98 FMI 3: Oil level sensor signal is open or shorted to supplyShorted highPACCAR MX-13
  • 4SPN 98 FMI 4: Signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowMack MP8, Mack MP7, PACCAR MX-13, Volvo D13
  • 5SPN 98 FMI 5: Current is below normal, or the circuit is openOpen circuitMack MP8, Mack MP7, PACCAR MX-13, Volvo D13
  • 16SPN 98 FMI 16: Oil level is above the normal range, moderately severeReal conditionPACCAR MX-13
  • 17SPN 98 FMI 17: Oil level is below the normal range, least severeReal conditionPACCAR MX-13
  • 18SPN 98 FMI 18: Value is below the normal range, moderately severe levelReal conditionMack MP8, Mack MP7, PACCAR MX-13, Volvo D13

Checks

0 of 5 done

When to stop

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

How urgent SPN 98 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Causes

  • Oil really low from consumption, a leak at the gaskets or filter, or a recent service that was not topped up
  • Oil level sensor in the sump fouled with sludge or fitted with a wrong part, giving a false reading
  • Sensor circuit fault: wiring open, shorted or corroded at the sump connector
  • Machine on a slope when read, so the sump level looks wrong

Source

Detroit Diesel DD15 2017-2020 fault codes list (Diesel Laptops)

This list names SPN 98 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.

The source covers: Detroit DD13 and DD15 (2017-2020); same SPN on other J1939 engines.

Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.