J1939 · Sensors
SPN 91 Fault Code
Accelerator pedal position 1
What does SPN 91 mean?
The driver's throttle demand, read from the position sensor in the pedal assembly or received as a message from the body module on multiplexed trucks. How urgent it is depends on the FMI after SPN 91 - pick it below. Check first: press the pedal slowly through its travel with the key on; the reading should rise smoothly, and a jump or full scale before half travel marks a bad track.
- SPN 91
- Accelerator pedal position 1
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 91 - pick it below.
What should I check first?
Press the pedal slowly through its travel with the key on; the reading should rise smoothly, and a jump or full scale before half travel marks a bad track
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 91?
You'll notice: Throttle response is wrong: the pedal may do nothing, the engine may sit at a fixed idle or limp-home speed, or it may rev without pedal input, and the check-engine lamp comes on.
Find the number shown after SPN 91 on your display. 3 of them have their own page with causes and checks.
- 0SPN 91 FMI 0: Pedal circuit reads highReal conditionDetroit DD15, Detroit DD13
- 1SPN 91 FMI 1: Pedal sensor 1 or 2 duty-cycle signal is too lowReal conditionPACCAR MX-13
- 2SPN 91 FMI 2: Data is erratic, intermittent or incorrectErratic or implausibleCummins ISX15
- 3SPN 91 FMI 3: Signal voltage is above normal, or the circuit is shorted to a high sourceShorted highCummins ISX15, PACCAR MX-13
- 4SPN 91 FMI 4: Signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowCummins ISX15, Detroit DD15, Detroit DD13, PACCAR MX-13
- 5SPN 91 FMI 5: Pedal sensor signal is open or below its expected rangeOpen circuitDetroit DD13 Gen 5, Detroit DD15 Gen 5
- 7SPN 91 FMI 7: Pedal is not returning to idle cleanly or the ECM does not recognise the idle positionPart or controllerDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5 and 1 more
- 8SPN 91 FMI 8: Abnormal frequency, pulse width or period of the signalErratic or implausibleCummins ISX15, PACCAR MX-13
- 9SPN 91 FMI 9: Abnormal update rate: the signal or message is late or missingLost messageCummins ISX15
- 10SPN 91 FMI 10: The value is changing at an abnormal rateErratic or implausibleMack MP8, Mack MP7, Volvo D13
- 12SPN 91 FMI 12: Pedal sensor has drifted outside the range the ECM learnedPart or controllerDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 13SPN 91 FMI 13: The value is out of calibrationPart or controllerCummins ISX15, Mack MP8, Mack MP7, Volvo D13
- 14SPN 91 FMI 14: The two-channel pedal has not been learned, so the ECM cannot trust the positionOtherDetroit DD15, Detroit DD13
- 19SPN 91 FMI 19: Network data for this parameter was received in errorLost messageCummins ISX15, Mack MP8, Mack MP7, Volvo D13
- 31SPN 91 FMI 31: The learned pedal travel range is too large to be validReal conditionDetroit DD15, Detroit DD13
Checks
0 of 5 done
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
How urgent SPN 91 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Signal high or open: broken or backed-out pin, an open sensor return, or the signal shorted to the 5 V reference at the accelerator pedal sensor 1
- Signal low or shorted: signal wire grounded, or the 5 V reference lost, so the accelerator pedal sensor 1 reads at the bottom of its range
- Real condition: pedal arm or return spring binding, so the sensor never returns to the idle position the ECM expects
- Real condition: pedal assembly worn or replaced with an unlearned unit, so idle and full-travel values are outside the learned range
1 more causeFewer causes
- Sensor: worn track in the pedal sensor that drops out in the part of the travel used most
Other Sensors codes
Source
Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)
This list names SPN 91 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
