EF Logo

J1939 · Engine speed/timing

SPN 723 Fault Code

Engine speed sensor 2 (camshaft)

What does SPN 723 mean?

The camshaft sensor that tells the ECM which cylinder is on which stroke. It is used together with the crankshaft signal for injection timing and engine synchronisation. How urgent it is depends on the FMI after SPN 723 - pick it below. Check first: compare the cam and crank signals while cranking in the service tool.

FaultActiveSPN 723FMI --J1939 engine ECU
SPN 723
Engine speed sensor 2 (camshaft)
FMI ?
How it failed - the number after the SPN

Can I keep running with it?

Depends on the FMI

How urgent it is depends on the FMI after SPN 723 - pick it below.

What should I check first?

Compare the cam and crank signals while cranking in the service tool

Then 4 more checks
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect a J1939-capable scan tool to the 9-pin diagnostic port.

Which FMI shows after SPN 723?

You'll notice: The cam position signal is missing or does not match the crank signal, so the ECM cannot time the injectors.

Find the number shown after SPN 723 on your display.

  • 2SPN 723 FMI 2: Data is erratic, intermittent or incorrectErratic or implausibleCummins ISX15
  • 7SPN 723 FMI 7: The mechanical part is not responding or is out of adjustmentPart or controllerCummins ISX15
  • 8SPN 723 FMI 8: The camshaft signal does not match the crankshaft position or has timed outErratic or implausibleDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5 and 1 more
  • 9SPN 723 FMI 9: Camshaft speed signal is out of range, or data is erraticLost messagePACCAR MX-13
  • 10SPN 723 FMI 10: Camshaft sensor signal is erratic or out of range during startErratic or implausibleDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5 and 1 more
  • 11SPN 723 FMI 11: Camshaft sensor has failed or its signal is disturbed or absentOtherDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5 and 1 more
  • 31SPN 723 FMI 31: The ECM detected the engine running backwardsReal conditionDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5

Checks

0 of 5 done

When to stop

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

How urgent SPN 723 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Causes

  • Cam sensor circuit fault: wiring open, shorted or chafed at the sensor plug
  • Sensor dirty, loose or at the wrong air gap
  • Cam gear or reluctor wheel damaged or fitted out of position
  • Timing gear wear causing the cam to be out of step with the crank

Source

Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)

This list names SPN 723 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.

The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.

Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.