J1939 · Aftertreatment - DPF
SPN 3485 Fault Code
Aftertreatment atomization air pressure
What does SPN 3485 mean?
Pressure of the compressed air used to atomize fuel at the aftertreatment burner or doser, read by a sensor on the air line. How urgent it is depends on the FMI after SPN 3485 - pick it below. Check first: check the atomization air line for leaks, kinks and water with the system pressurised.
- SPN 3485
- Aftertreatment atomization air pressure
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 3485 - pick it below.
What should I check first?
Check the atomization air line for leaks, kinks and water with the system pressurised
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 3485?
You'll notice: Fuel cannot be atomized properly, so burner or regeneration performance suffers and the system may log a failed regeneration.
Find the number shown after SPN 3485 on your display.
- 2SPN 3485 FMI 2: Aftertreatment atomization air pressure data is erratic, intermittent or incorrectErratic or implausibleMack MP8, Mack MP7, Volvo D13
- 3SPN 3485 FMI 3: Aftertreatment atomization air pressure signal voltage is above normal, or the circuit is shorted to a high sourceShorted highMack MP8, Mack MP7, Volvo D13
- 5SPN 3485 FMI 5: Current in the Aftertreatment atomization air pressure circuit is below normal, or the circuit is openOpen circuitMack MP8, Mack MP7, Volvo D13
- 7SPN 3485 FMI 7: The Aftertreatment atomization air pressure is not responding or is out of adjustmentPart or controllerMack MP8, Mack MP7, Volvo D13
- 10SPN 3485 FMI 10: Aftertreatment atomization air pressure is changing at an abnormal rateErratic or implausibleMack MP8, Mack MP7, Volvo D13
- 14SPN 3485 FMI 14: Special-instruction fault for the Aftertreatment atomization air pressure; the maker lists a dedicated procedure for itOtherMack MP8, Mack MP7, Volvo D13
Checks
0 of 5 done
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
How urgent SPN 3485 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Air line to the burner kinked, leaking or iced with moisture
- Sensor line blocked
- Sensor failed
- Air supply pressure low from the vehicle air system
Other Aftertreatment - DPF codes
Source
Mack MP8 2010-2013 fault code list (Diesel Laptops)
This list names SPN 3485 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Mack MP7, Mack MP8, Volvo D13; same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
