J1939 · Aftertreatment - SCR/DEF
SPN 3031 Fault Code
Aftertreatment 1 DEF tank temperature
What does SPN 3031 mean?
Temperature of the DEF in its tank, read by a sensor in the tank module. The aftertreatment control uses it to decide when to heat or thaw the fluid. How urgent it is depends on the FMI after SPN 3031 - pick it below. Check first: compare the DEF tank temperature with ambient after an overnight soak; a stuck value points to the sensor or wiring.
- SPN 3031
- Aftertreatment 1 DEF tank temperature
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 3031 - pick it below.
What should I check first?
Compare the DEF tank temperature with ambient after an overnight soak; a stuck value points to the sensor or wiring
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 3031?
You'll notice: The DEF tank temperature is misread, so the ECM may heat the tank at the wrong time or not at all.
Find the number shown after SPN 3031 on your display. 2 of them have their own page with causes and checks.
- 0SPN 3031 FMI 0: Value is above the normal range, most severe levelReal conditionMack MP8, Mack MP7, Volvo D13
- 2SPN 3031 FMI 2: Data is erratic, intermittent or incorrectErratic or implausibleCummins ISX15, PACCAR MX-13
- 3SPN 3031 FMI 3: Signal voltage is above normal, or the circuit is shorted to a high sourceShorted highCummins ISX15, Detroit DD15, Detroit DD13, Detroit DD13 Gen 5 and 2 more
- 4SPN 3031 FMI 4: Signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowCummins ISX15, Detroit DD15, Detroit DD13, Detroit DD13 Gen 5 and 5 more
- 5SPN 3031 FMI 5: Current is below normal, or the circuit is openOpen circuitMack MP8, Mack MP7, Volvo D13
- 8SPN 3031 FMI 8: Abnormal frequency, pulse width or period of the signalErratic or implausibleMack MP8, Mack MP7, Volvo D13
- 9SPN 3031 FMI 9: Abnormal update rate: the signal or message is late or missingLost messageCummins ISX15
- 10SPN 3031 FMI 10: DEF tank temperature is erraticErratic or implausibleDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 13SPN 3031 FMI 13: The value is out of calibrationPart or controllerCummins ISX15
- 18SPN 3031 FMI 18: Value is below the normal range, moderately severe levelReal conditionCummins ISX15
- 19SPN 3031 FMI 19: DEF tank temperature arrived in error over CANLost messageDetroit DD15, Detroit DD13, PACCAR MX-13
Checks
0 of 5 done
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
How urgent SPN 3031 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Reads cold: an open circuit or a short to supply in the DEF tank temperature sensor wiring, which the ECM reads as an extremely low temperature
- Reads hot: signal wire shorted to ground or the DEF tank temperature sensor element shorted, which the ECM reads as an extremely high temperature
- Real condition: tank heater not warming the fluid, so the real temperature stays low in cold weather
- Real condition: heater coolant supply restricted or valve stuck closed
1 more causeFewer causes
- Sensor: dEF crystals on the sender pins making the reading drift with temperature
Other Aftertreatment - SCR/DEF codes
Source
Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)
This list names SPN 3031 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
