EF Logo

J1939 · Electrical

SPN 168 Fault Code

Battery potential / power input 1

What does SPN 168 mean?

Battery voltage at the ECM's power input. The ECM monitors it so a weak battery, poor ground or bad charging does not upset sensors and injector drivers. How urgent it is depends on the FMI after SPN 168 - pick it below. Check first: measure battery voltage at the terminals and at the ECM connector with the engine off and running.

FaultActiveSPN 168FMI --J1939 engine ECU
SPN 168
Battery potential / power input 1
FMI ?
How it failed - the number after the SPN

Can I keep running with it?

Depends on the FMI

How urgent it is depends on the FMI after SPN 168 - pick it below.

What should I check first?

Measure battery voltage at the terminals and at the ECM connector with the engine off and running

Then 4 more checks
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect a J1939-capable scan tool to the 9-pin diagnostic port.

Which FMI shows after SPN 168?

You'll notice: Battery voltage at the ECM is too high or too low, so electronics may misbehave.

Find the number shown after SPN 168 on your display. 2 of them have their own page with causes and checks.

  • 0SPN 168 FMI 0: Battery voltage at the ECM is too highReal conditionDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
  • 1SPN 168 FMI 1: Battery voltage at the ECM is too low or the power input is openReal conditionDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5 and 1 more
  • 2SPN 168 FMI 2: Ignition circuit voltage is erraticErratic or implausibleDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
  • 4SPN 168 FMI 4: ECU power supply voltage is too lowShorted lowPACCAR MX-13
  • 5SPN 168 FMI 5: Battery voltage input is open circuit at the ECMOpen circuitDetroit DD15, Detroit DD13
  • 7SPN 168 FMI 7: Optimized idle detected a charging system or battery failurePart or controllerDetroit DD15, Detroit DD13
  • 9SPN 168 FMI 9: The ECM has lost its battery connectionLost messageDetroit DD15, Detroit DD13
  • 14SPN 168 FMI 14: Optimized idle flagged a charging or battery failure, or the ECU did not power down properlyOtherDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
  • 15SPN 168 FMI 15: Value is above the normal range, least severe levelReal conditionCummins ISX15
  • 16SPN 168 FMI 16: Value is above the normal range, moderately severe levelReal conditionCummins ISX15
  • 17SPN 168 FMI 17: Value is below the normal range, least severe levelReal conditionCummins ISX15
  • 18SPN 168 FMI 18: Value is below the normal range, moderately severe levelReal conditionCummins ISX15
  • 19SPN 168 FMI 19: A message carrying the aftertreatment power supply value arrived in error over CANLost messagePACCAR MX-13

Checks

0 of 5 done

When to stop

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

How urgent SPN 168 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Causes

  • Low voltage: weak or discharged batteries, a loose terminal or a corroded ground strap
  • Charging fault: alternator not charging or overcharging from a failed regulator
  • High resistance in the ECM power feed or ground, giving low voltage at the ECM only
  • Jump-start or wrong battery connection raising or reversing the voltage

Source

Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)

This list names SPN 168 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.

The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.

Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.