EF Logo

Hyundai · Machine codes (MCU, HCESPN)

Hyundai Steering pressure sensors and emergency steering pump relay fault codes

The steering main pump and the emergency steering pump each have an oil pressure sensor, and the emergency pump has a relay switched by the MCU. The MCU compares the readings to confirm there is steering pressure and to start the standby pump if the main pump falls short.

FaultCheck187-4Hyundai · Steering pressure sensors and emergency steering pump relay
Code shows hereFAULT187-4

Where this code shows

Turn the key on and open the fault code or diagnosis menu on the cluster.

What do these codes mean?

Hyundai codes 187-4 to 203-4 are all about the steering pressure sensors and emergency steering pump relay. The most common failure type is shorted low (4 of 10); none needs an immediate stop. Start with this check: read both steering pressure values on the cluster at idle and at high idle and see whether they agree with the steering feel.

How urgent are they?

None of the 10 codes here means stop now; all 10 can wait until the shift ends, but find the cause before the next one.

  • Check soon10

What should I check first?

Read both steering pressure values on the cluster at idle and at high idle and see whether they agree with the steering feel

Shared checks

10 of 10

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Hyundai 187-4Emergency steering pump relay circuit voltage below normal, shorted to low source or open

    The MCU finds the Emergency steering pump relay circuit voltage low, which it reads as a short to ground or an open circuit on the driver line.· Shorted low
    Check soon

    Causes

    • Open wire or loose pin between the MCU and the emergency steering pump relay
    • Driver wire chafed to ground near the emergency steering pump relay
    • the emergency steering pump relay coil open or shorted

    Checks

    1. 1Unplug the emergency steering pump relay and measure coil resistance: an open reading or a near-zero reading shows which way the coil failed
    2. 2Check the driver wire from the MCU to the emergency steering pump relay for continuity and for a path to ground
    3. 3Listen for the relay click during the emergency pump test and check the pump actually spins
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai 187-6Emergency steering pump relay circuit current above normal

    The MCU measures more current than normal on the Emergency steering pump relay circuit, usually a shorted coil or a driver wire touching supply.· Shorted low
    Check soon

    Causes

    • the emergency steering pump relay coil shorted between turns
    • Driver wire touching a supply wire
    • Water in the connector bridging two pins

    Checks

    1. 1Measure the emergency steering pump relay coil resistance against a known-good twin and look for a low reading
    2. 2Inspect the connector for water or corrosion bridging pins, then clear the code and see if it returns at once
    3. 3Listen for the relay click during the emergency pump test and check the pump actually spins
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai 202-0Steering main pump pressure sensor data above normal range

    The MCU reads the Steering main pump pressure sensor above its normal range, or the signal is floating open so the reading pegs high.· Real condition
    Check soon

    Causes

    • Real pressure above normal: priority valve stuck or relief set wrongly
    • Open signal or ground wire at the the steering main pump pressure sensor connector
    • the steering main pump pressure sensor failed and reading high

    Checks

    1. 1Read the Steering main pump value on the cluster and compare it with a test gauge on the main steering pump outlet before blaming the sensor
    2. 2Unplug the steering main pump pressure sensor and inspect the connector and the wire run for a break; an open line makes the reading rail high
    3. 3Steer lock to lock at idle and watch the main pump pressure rise and fall with the steering effort
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Hyundai 202-1Steering main pump pressure sensor data below normal range

    The MCU reads the Steering main pump pressure sensor below its normal range, so the pressure it expects on the main steering pump outlet is not showing up in the signal.· Real condition
    Check soon

    Causes

    • Low real pressure on the main steering pump outlet: weak pump, internal leak or a stuck-open relief
    • Partly shorted or high-resistance signal wire at the steering main pump pressure sensor
    • the steering main pump pressure sensor drifted or failed low

    Checks

    1. 1Compare the cluster Steering main pump reading with a mechanical gauge on the main steering pump outlet; if the gauge is good the sensor or wiring is at fault
    2. 2Check the the steering main pump pressure sensor connector for water or green corrosion that adds resistance to the signal
    3. 3Steer lock to lock at idle and watch the main pump pressure rise and fall with the steering effort
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Hyundai 202-2Steering main pump pressure sensor data error

    The MCU decides the Steering main pump pressure sensor signal is not plausible, for example jumping or disagreeing with the rest of the system.· Erratic or implausible
    Check soon

    Causes

    • Intermittent contact in the the steering main pump pressure sensor connector or harness
    • Electrical noise or a weak chassis ground on the sensor supply
    • the steering main pump pressure sensor failing intermittently

    Checks

    1. 1Watch the Steering main pump reading while wiggling the harness at the steering main pump pressure sensor; a jump when you move it means a connection fault
    2. 2Check the sensor ground and 5 V supply for steady values with the engine running and under load
    3. 3Steer lock to lock at idle and watch the main pump pressure rise and fall with the steering effort
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Hyundai 202-4Steering main pump pressure sensor circuit voltage below normal

    The MCU sees the Steering main pump pressure sensor circuit pulled low, which it reads as a short to ground or a lost supply to the sensor.· Shorted low
    Check soon

    Causes

    • Signal wire rubbed through to ground near the steering main pump pressure sensor
    • the steering main pump pressure sensor shorted internally
    • Sensor 5 V supply lost or pulled down by another shorted sensor on the same reference

    Checks

    1. 1Unplug the steering main pump pressure sensor and see whether the code changes from circuit low to an open-type code; if so the sensor was pulling the line down
    2. 2Measure the 5 V reference at the the steering main pump pressure sensor connector with key on and compare it with a neighbouring sensor on the same supply
    3. 3Steer lock to lock at idle and watch the main pump pressure rise and fall with the steering effort
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai 203-0Emergency steering pump pressure sensor data above normal range

    The MCU reads the Emergency steering pump pressure sensor above its normal range, or the signal is floating open so the reading pegs high.· Real condition
    Check soon

    Causes

    • Real pressure high at the emergency pump: blocked line or stuck relief
    • Open signal or ground wire at the the emergency steering pump pressure sensor connector
    • the emergency steering pump pressure sensor failed and reading high

    Checks

    1. 1Read the Emergency steering pump value on the cluster and compare it with a test gauge on the emergency pump outlet line before blaming the sensor
    2. 2Unplug the emergency steering pump pressure sensor and inspect the connector and the wire run for a break; an open line makes the reading rail high
    3. 3Run the emergency steering test from the cluster if it offers one and watch this pressure rise
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Hyundai 203-1Emergency steering pump pressure sensor data below normal range

    The MCU reads the Emergency steering pump pressure sensor below its normal range, so the pressure it expects on the emergency pump outlet line is not showing up in the signal.· Real condition
    Check soon

    Causes

    • Low real pressure on the emergency pump outlet line: weak pump, internal leak or a stuck-open relief
    • Partly shorted or high-resistance signal wire at the emergency steering pump pressure sensor
    • the emergency steering pump pressure sensor drifted or failed low

    Checks

    1. 1Compare the cluster Emergency steering pump reading with a mechanical gauge on the emergency pump outlet line; if the gauge is good the sensor or wiring is at fault
    2. 2Check the the emergency steering pump pressure sensor connector for water or green corrosion that adds resistance to the signal
    3. 3Run the emergency steering test from the cluster if it offers one and watch this pressure rise
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Hyundai 203-2Emergency steering pump pressure sensor data error

    The MCU decides the Emergency steering pump pressure sensor signal is not plausible, for example jumping or disagreeing with the rest of the system.· Erratic or implausible
    Check soon

    Causes

    • Intermittent contact in the the emergency steering pump pressure sensor connector or harness
    • Electrical noise or a weak chassis ground on the sensor supply
    • the emergency steering pump pressure sensor failing intermittently

    Checks

    1. 1Watch the Emergency steering pump reading while wiggling the harness at the emergency steering pump pressure sensor; a jump when you move it means a connection fault
    2. 2Check the sensor ground and 5 V supply for steady values with the engine running and under load
    3. 3Run the emergency steering test from the cluster if it offers one and watch this pressure rise
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Hyundai 203-4Emergency steering pump pressure sensor circuit voltage below normal

    The MCU sees the Emergency steering pump pressure sensor circuit pulled low, which it reads as a short to ground or a lost supply to the sensor.· Shorted low
    Check soon

    Causes

    • Signal wire rubbed through to ground near the emergency steering pump pressure sensor
    • the emergency steering pump pressure sensor shorted internally
    • Sensor 5 V supply lost or pulled down by another shorted sensor on the same reference

    Checks

    1. 1Unplug the emergency steering pump pressure sensor and see whether the code changes from circuit low to an open-type code; if so the sensor was pulling the line down
    2. 2Measure the 5 V reference at the the emergency steering pump pressure sensor connector with key on and compare it with a neighbouring sensor on the same supply
    3. 3Run the emergency steering test from the cluster if it offers one and watch this pressure rise
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

Shared checks

Checks, in order

  1. 1Read both steering pressure values on the cluster at idle and at high idle and see whether they agree with the steering feel
  2. 2Fit a test gauge on the steering circuit to tell a bad sensor from a real low-pressure condition
  3. 3Check the sensor connectors and the relay base for water or green corrosion
  4. 4Inspect the harness through the articulation joint where it flexes on every turn
  5. 5Swap the relay with a known-good identical one if the relay circuit code is active

Causes

  • Steering pressure sensor connector corroded or loose at the pump side
  • Emergency pump relay or its base faulty
  • Priority valve stuck or steering pump worn
  • Harness chafed where it passes through the articulation joint

Most common here: shorted low (4 of 10)

Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

When to stop

You'll notice: The steering warning may show, the emergency pump may run when it should not, or steering may feel heavy at idle.

Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.