EF Logo

Hyundai · Machine codes (MCU, HCESPN)

Hyundai Cooling fan, coolant and hydraulic oil temperature circuits fault codes

These codes cover the hydraulic oil and engine coolant temperature sensors and the engine cooling fan circuits: the fan EPPR valve, the fan reverse solenoid, its status signal and the fan speed signal. The MCU uses the temperature readings to drive the fan and to warn the operator, so a fault here usually shows as a fan running wrongly or a false temperature reading.

FaultCheck101-3Hyundai · Cooling fan, coolant and hydraulic oil temperature circuits
Code shows hereFAULT101-3

Where this code shows

Turn the key on and open the fault code or diagnosis menu on the cluster.

What do these codes mean?

Hyundai codes 101-3 to 318-8 are all about the cooling fan, coolant and hydraulic oil temperature circuits. Most are shorted low faults; none needs an immediate stop. Start with this check: check the connectors at the temperature sensors and at the fan valve for water, corrosion and pushed-back pins before measuring anything.

How urgent are they?

None of the 11 codes here means stop now; all 11 can wait until the shift ends, but find the cause before the next one.

  • Check soon11

What should I check first?

Check the connectors at the temperature sensors and at the fan valve for water, corrosion and pushed-back pins before measuring anything

Shared checks

11 of 11

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Hyundai 101-3Hydraulic oil temperature sensor circuit voltage above normal

    The MCU sees the hydraulic oil temperature signal at a voltage above the normal window, which it takes as a short to a high source or an open signal wire.· Shorted high
    Check soon

    Causes

    • Hydraulic oil temperature sensor unplugged or connector pin pushed back
    • Signal wire broken or shorted to a supply wire
    • Sensor failed open
    • MCU input damaged

    Checks

    1. 1Check the oil temperature reading on the cluster and compare it with an infrared reading on the hydraulic tank
    2. 2Unplug the sensor with the key on and measure the signal pin: a reading pinned near supply with the plug off means the harness or MCU, not the sensor
    3. 3Inspect the sensor connector for corrosion, a bent terminal or a loose lock before replacing the sensor
    4. 4Check the wire from the sensor to the MCU for continuity and for contact with any supply wire
    5. 5Clear the code and see whether it returns instantly or only after warm-up
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Hyundai 101-4Hydraulic oil temperature sensor circuit voltage below normal

    The MCU sees the Hydraulic oil temperature sensor signal pulled down below its normal voltage window, which it reads as a short to ground or a dead supply.· Shorted low
    Check soon

    Causes

    • Signal wire chafed to the frame or to a ground wire near the the hydraulic oil temperature sensor
    • the hydraulic oil temperature sensor failed internally and pulling its signal low
    • Lost 5 V reference to the part

    Checks

    1. 1Unplug the hydraulic oil temperature sensor and measure its 5 V reference pin: no supply means a harness or MCU output problem
    2. 2With the plug off, check the signal wire for continuity to ground along its run toward the MCU
    3. 3Compare the cluster oil temperature with a surface thermometer on the hydraulic tank to see how far off it is
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai 145-5Engine cooling fan EPPR valve circuit current below normal or open

    The MCU measures too little current on the Engine cooling fan EPPR valve circuit, which it reads as an open coil or a broken driver wire.· Open circuit
    Check soon

    Causes

    • Open coil in the cooling fan EPPR valve
    • Broken or loose wire at the the cooling fan EPPR valve connector
    • Poor ground return

    Checks

    1. 1Check continuity through the cooling fan EPPR valve coil with the plug off; infinity means the coil is open
    2. 2Look for a pushed-back pin at the connector and a broken wire inside the insulation
    3. 3Watch fan speed while the engine warms up: a fan that never changes speed points to the EPPR output rather than a sensor
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Hyundai 145-6Engine cooling fan EPPR valve circuit current above normal

    The MCU measures more current than normal on the Engine cooling fan EPPR valve circuit, usually a shorted coil or a driver wire touching supply.· Shorted low
    Check soon

    Causes

    • the cooling fan EPPR valve coil shorted between turns
    • Driver wire touching a supply wire
    • Water in the connector bridging two pins

    Checks

    1. 1Measure the cooling fan EPPR valve coil resistance against a known-good twin and look for a low reading
    2. 2Inspect the connector for water or corrosion bridging pins, then clear the code and see if it returns at once
    3. 3Watch fan speed while the engine warms up: a fan that never changes speed points to the EPPR output rather than a sensor
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai 181-4Engine cooling fan reverse solenoid circuit voltage below normal, shorted to low source or open

    The MCU finds the Engine cooling fan reverse solenoid circuit voltage low, which it reads as a short to ground or an open circuit on the driver line.· Shorted low
    Check soon

    Causes

    • Open wire or loose pin between the MCU and the fan reverse solenoid
    • Driver wire chafed to ground near the fan reverse solenoid
    • the fan reverse solenoid coil open or shorted

    Checks

    1. 1Unplug the fan reverse solenoid and measure coil resistance: an open reading or a near-zero reading shows which way the coil failed
    2. 2Check the driver wire from the MCU to the fan reverse solenoid for continuity and for a path to ground
    3. 3Trigger the fan reverse cycle from the cluster menu and listen for the solenoid and the change in airflow direction
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai 181-6Engine cooling fan reverse solenoid circuit current above normal

    The MCU measures more current than normal on the Engine cooling fan reverse solenoid circuit, usually a shorted coil or a driver wire touching supply.· Shorted low
    Check soon

    Causes

    • the fan reverse solenoid coil shorted between turns
    • Driver wire touching a supply wire
    • Water in the connector bridging two pins

    Checks

    1. 1Measure the fan reverse solenoid coil resistance against a known-good twin and look for a low reading
    2. 2Inspect the connector for water or corrosion bridging pins, then clear the code and see if it returns at once
    3. 3Trigger the fan reverse cycle from the cluster menu and listen for the solenoid and the change in airflow direction
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai 183-4Engine cooling fan reverse driving status signal circuit voltage below normal, shorted to low source or open

    The MCU finds the Engine cooling fan reverse driving status signal circuit voltage low, which it reads as a short to ground or an open circuit on the driver line.· Shorted low
    Check soon

    Causes

    • Open wire or loose pin between the MCU and the fan reverse status signal wire
    • Driver wire chafed to ground near the fan reverse status signal wire
    • the fan reverse status signal wire coil open or shorted

    Checks

    1. 1Unplug the fan reverse status signal wire and measure coil resistance: an open reading or a near-zero reading shows which way the coil failed
    2. 2Check the driver wire from the MCU to the fan reverse status signal wire for continuity and for a path to ground
    3. 3Compare the status wire with the reverse solenoid state: if the solenoid works but this code stays, the feedback wire or its connector is the fault
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai 183-6Engine cooling fan reverse driving status signal circuit current above normal

    The MCU measures more current than normal on the Engine cooling fan reverse driving status signal circuit, usually a shorted coil or a driver wire touching supply.· Shorted low
    Check soon

    Causes

    • the fan reverse status signal wire coil shorted between turns
    • Driver wire touching a supply wire
    • Water in the connector bridging two pins

    Checks

    1. 1Measure the fan reverse status signal wire coil resistance against a known-good twin and look for a low reading
    2. 2Inspect the connector for water or corrosion bridging pins, then clear the code and see if it returns at once
    3. 3Compare the status wire with the reverse solenoid state: if the solenoid works but this code stays, the feedback wire or its connector is the fault
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai 304-3Engine coolant temperature sensor circuit voltage above normal

    The MCU sees the Engine coolant temperature sensor signal sitting above its normal voltage window, which it reads as a short to a high source or a broken signal wire.· Shorted high
    Check soon

    Causes

    • Open or pushed-back pin in the the engine coolant temperature sensor connector
    • Signal wire shorted to a supply wire in the harness
    • the engine coolant temperature sensor failed internally

    Checks

    1. 1Key on, unplug the engine coolant temperature sensor and measure the signal pin: a reading stuck near supply points at the harness or the MCU, not the part
    2. 2Pull the the engine coolant temperature sensor connector, check each pin for corrosion, bent terminals or a lifted lock, then clear the code and recheck
    3. 3Warm the engine and watch the coolant reading move smoothly; a frozen reading with a good plug points at the sensor itself
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Hyundai 304-4Engine coolant temperature sensor circuit voltage below normal

    The MCU sees the Engine coolant temperature sensor signal pulled down below its normal voltage window, which it reads as a short to ground or a dead supply.· Shorted low
    Check soon

    Causes

    • Signal wire chafed to the frame or to a ground wire near the the engine coolant temperature sensor
    • the engine coolant temperature sensor failed internally and pulling its signal low
    • Lost 5 V reference to the part

    Checks

    1. 1Unplug the engine coolant temperature sensor and measure its 5 V reference pin: no supply means a harness or MCU output problem
    2. 2With the plug off, check the signal wire for continuity to ground along its run toward the MCU
    3. 3Cold-check the reading after an overnight stand: it should match ambient, and a reading far from ambient shows a shorted sender or wire
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai 318-8Engine cooling fan speed signal error, abnormal frequency or pulse width

    The MCU receives a fan speed signal whose frequency or pulse width is outside what it expects.· Erratic or implausible
    Check soon

    Causes

    • Fan speed pickup gap wrong or sensor damaged by debris
    • Pickup wire chafed or noisy near the fan drive
    • Fan drive slipping or running far from its commanded speed

    Checks

    1. 1Check the pickup gap and the sensor face for metal swarf or damage
    2. 2Run the fan from cool to hot while watching the cluster fan speed: a signal that jumps points to the pickup wiring
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

Shared checks

Checks, in order

  1. 1Check the connectors at the temperature sensors and at the fan valve for water, corrosion and pushed-back pins before measuring anything
  2. 2Compare each temperature reading on the cluster with an infrared thermometer on the same component to see whether the reading is believable
  3. 3Measure coil resistance of the fan valve and reverse solenoid with the plug off and compare with the other side or a spare
  4. 4Look along the harness near the fan shroud and engine mount for rubbed insulation
  5. 5Clear the code and run the machine until warm to see whether it returns immediately or only when hot

Causes

  • Sensor connector corroded or loose on the radiator, tank or engine side
  • Fan EPPR or reverse solenoid connector filled with water
  • Harness chafed against the fan shroud or engine bracket
  • Failed temperature sensor or fan solenoid coil

Most codes here: shorted low (7 of 11)

Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

When to stop

You'll notice: The fan may run flat out or not respond to temperature, a temperature gauge may read zero or full scale, and the cluster shows the HCESPN number with its FMI.

Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.