EF Logo

Hyundai · Machine codes (MCU, HCESPN)

Hyundai Boom and bucket cylinder pressure sensors fault codes

One pressure sensor reads the boom cylinder circuit and another reads the bucket cylinder circuit. The MCU takes these readings as part of loader control, so a fault gives a false or missing pressure value rather than a hydraulic failure by itself.

FaultCheck204-0Hyundai · Boom and bucket cylinder pressure sensors
Code shows hereFAULT204-0

Where this code shows

Turn the key on and open the fault code or diagnosis menu on the cluster.

What do these codes mean?

Hyundai codes 204-0 to 205-4 are all about the boom and bucket cylinder pressure sensors. The most common failure type is real condition (4 of 8); none needs an immediate stop. Start with this check: compare the cluster reading with a mechanical gauge on the same cylinder circuit before replacing a sensor.

How urgent are they?

None of the 8 codes here means stop now; all 8 can wait until the shift ends, but find the cause before the next one.

  • Check soon8

What should I check first?

Compare the cluster reading with a mechanical gauge on the same cylinder circuit before replacing a sensor

Shared checks

8 of 8

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Hyundai 204-0Boom cylinder pressure sensor data above normal range

    The MCU reads the Boom cylinder pressure sensor above its normal range, or the signal is floating open so the reading pegs high.· Real condition
    Check soon

    Causes

    • Real boom circuit pressure higher than normal: stuck relief or load held against the stops
    • Open signal or ground wire at the the boom cylinder pressure sensor connector
    • the boom cylinder pressure sensor failed and reading high

    Checks

    1. 1Read the Boom cylinder value on the cluster and compare it with a test gauge on the boom cylinder circuit before blaming the sensor
    2. 2Unplug the boom cylinder pressure sensor and inspect the connector and the wire run for a break; an open line makes the reading rail high
    3. 3Hold the empty boom still and compare its reading with the boom raised against load
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Hyundai 204-1Boom cylinder pressure sensor data below normal range

    The MCU reads the Boom cylinder pressure sensor below its normal range, so the pressure it expects on the boom cylinder circuit is not showing up in the signal.· Real condition
    Check soon

    Causes

    • Low real pressure on the boom cylinder circuit: weak pump, internal leak or a stuck-open relief
    • Partly shorted or high-resistance signal wire at the boom cylinder pressure sensor
    • the boom cylinder pressure sensor drifted or failed low

    Checks

    1. 1Compare the cluster Boom cylinder reading with a mechanical gauge on the boom cylinder circuit; if the gauge is good the sensor or wiring is at fault
    2. 2Check the the boom cylinder pressure sensor connector for water or green corrosion that adds resistance to the signal
    3. 3Hold the empty boom still and compare its reading with the boom raised against load
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Hyundai 204-2Boom cylinder pressure sensor data error

    The MCU decides the Boom cylinder pressure sensor signal is not plausible, for example jumping or disagreeing with the rest of the system.· Erratic or implausible
    Check soon

    Causes

    • Intermittent contact in the the boom cylinder pressure sensor connector or harness
    • Electrical noise or a weak chassis ground on the sensor supply
    • the boom cylinder pressure sensor failing intermittently

    Checks

    1. 1Watch the Boom cylinder reading while wiggling the harness at the boom cylinder pressure sensor; a jump when you move it means a connection fault
    2. 2Check the sensor ground and 5 V supply for steady values with the engine running and under load
    3. 3Hold the empty boom still and compare its reading with the boom raised against load
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Hyundai 204-4Boom cylinder pressure sensor circuit voltage below normal

    The MCU sees the Boom cylinder pressure sensor circuit pulled low, which it reads as a short to ground or a lost supply to the sensor.· Shorted low
    Check soon

    Causes

    • Signal wire rubbed through to ground near the boom cylinder pressure sensor
    • the boom cylinder pressure sensor shorted internally
    • Sensor 5 V supply lost or pulled down by another shorted sensor on the same reference

    Checks

    1. 1Unplug the boom cylinder pressure sensor and see whether the code changes from circuit low to an open-type code; if so the sensor was pulling the line down
    2. 2Measure the 5 V reference at the the boom cylinder pressure sensor connector with key on and compare it with a neighbouring sensor on the same supply
    3. 3Hold the empty boom still and compare its reading with the boom raised against load
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai 205-0Bucket cylinder pressure sensor data above normal range

    The MCU reads the Bucket cylinder pressure sensor above its normal range, or the signal is floating open so the reading pegs high.· Real condition
    Check soon

    Causes

    • Real bucket circuit pressure higher than normal: bucket held against its stop or relief stuck
    • Open signal or ground wire at the the bucket cylinder pressure sensor connector
    • the bucket cylinder pressure sensor failed and reading high

    Checks

    1. 1Read the Bucket cylinder value on the cluster and compare it with a test gauge on the bucket cylinder circuit before blaming the sensor
    2. 2Unplug the bucket cylinder pressure sensor and inspect the connector and the wire run for a break; an open line makes the reading rail high
    3. 3Tilt the bucket against its stop and see whether the reading rises as the cylinder bottoms
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Hyundai 205-1Bucket cylinder pressure sensor data below normal range

    The MCU reads the Bucket cylinder pressure sensor below its normal range, so the pressure it expects on the bucket cylinder circuit is not showing up in the signal.· Real condition
    Check soon

    Causes

    • Low real pressure on the bucket cylinder circuit: weak pump, internal leak or a stuck-open relief
    • Partly shorted or high-resistance signal wire at the bucket cylinder pressure sensor
    • the bucket cylinder pressure sensor drifted or failed low

    Checks

    1. 1Compare the cluster Bucket cylinder reading with a mechanical gauge on the bucket cylinder circuit; if the gauge is good the sensor or wiring is at fault
    2. 2Check the the bucket cylinder pressure sensor connector for water or green corrosion that adds resistance to the signal
    3. 3Tilt the bucket against its stop and see whether the reading rises as the cylinder bottoms
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Hyundai 205-2Bucket cylinder pressure sensor data error

    The MCU decides the Bucket cylinder pressure sensor signal is not plausible, for example jumping or disagreeing with the rest of the system.· Erratic or implausible
    Check soon

    Causes

    • Intermittent contact in the the bucket cylinder pressure sensor connector or harness
    • Electrical noise or a weak chassis ground on the sensor supply
    • the bucket cylinder pressure sensor failing intermittently

    Checks

    1. 1Watch the Bucket cylinder reading while wiggling the harness at the bucket cylinder pressure sensor; a jump when you move it means a connection fault
    2. 2Check the sensor ground and 5 V supply for steady values with the engine running and under load
    3. 3Tilt the bucket against its stop and see whether the reading rises as the cylinder bottoms
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Hyundai 205-4Bucket cylinder pressure sensor circuit voltage below normal

    The MCU sees the Bucket cylinder pressure sensor circuit pulled low, which it reads as a short to ground or a lost supply to the sensor.· Shorted low
    Check soon

    Causes

    • Signal wire rubbed through to ground near the bucket cylinder pressure sensor
    • the bucket cylinder pressure sensor shorted internally
    • Sensor 5 V supply lost or pulled down by another shorted sensor on the same reference

    Checks

    1. 1Unplug the bucket cylinder pressure sensor and see whether the code changes from circuit low to an open-type code; if so the sensor was pulling the line down
    2. 2Measure the 5 V reference at the the bucket cylinder pressure sensor connector with key on and compare it with a neighbouring sensor on the same supply
    3. 3Tilt the bucket against its stop and see whether the reading rises as the cylinder bottoms
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

Shared checks

Checks, in order

  1. 1Compare the cluster reading with a mechanical gauge on the same cylinder circuit before replacing a sensor
  2. 2Inspect the harness along the lift arm for chafing and for plugs left unseated after service
  3. 3Check the sensor port for oil seepage that points to a damaged seal on the sensor
  4. 4Measure the sensor 5 V supply and ground with the plug off and key on
  5. 5Unplug one sensor at a time and note whether the other sensor's code changes, which shows a shared supply fault

Causes

  • Sensor connector or wiring damaged where it runs along the lift arms
  • Sensor port fitting leaking or the sensor failed
  • Real hydraulic fault in the cylinder circuit
  • Weak 5 V supply shared with another sensor

Most common here: real condition (4 of 8)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: A cylinder pressure reading on the cluster looks wrong or is missing, and the HCESPN number appears with FMI 0, 1, 2 or 4.

Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.