EF Logo

Genie · Operational indicator codes

Genie Operational indicator codes (LCD and LED) fault codes

These are status codes shown on the platform display or LED, not electrical faults: off level, platform overload, chassis mode, pothole guard stuck, no drive, lifting disabled, charger interlock, obstruction, brake release and the working height limit messages. Each tells the operator why a function is blocked.

FaultInfoCHrgGenie · Operational indicator codes (LCD and LED)
Code shows hereFAULTCHrg

Where this code shows

Scissors: read the code on the platform LED display or the ground control LCD.

What do these codes mean?

Genie codes br to PHS are all about the operational indicator codes (LCD and LED). The most common failure type is real condition (4 of 12); 1 needs an immediate stop. Start with this check: read the indicator on the platform display and match it to the section below before testing anything.

How urgent are they?

1 of 12 codes here means stop now; 2 can wait until the shift ends, but find the cause before the next one; 9 are information only.

  • Stop now1
  • Check soon2
  • Info9

What should I check first?

Read the indicator on the platform display and match it to the section below before testing anything.

Shared checks

12 of 12

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Genie brBrake release

    The drive brakes were released by hand, for towing or lowering with the manual release, so drive and lift are disabled.· Other
    Info

    Causes

    • Manual brake release valve engaged
    • Brake release valve left open after towing
    • Brake release hand pump handle stuck in the released position
    • Brake release monitoring switch faulty

    Checks

    1. 1Close the manual brake release valve fully (turn the knob or lever back to the run position).
    2. 2Check the hand pump handle has returned and the brake release valve is not weeping or held open.
    3. 3Secure the machine on level ground and key off and on to see if br clears.
    4. 4If br stays with the valve closed, check the brake release monitoring switch and wiring for a stuck contact.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie CHChassis mode operation

    The ground controls are selected, so the machine is running in chassis mode and the platform controls are locked out.· Other
    Info

    Causes

    • Key switch left in the ground (chassis) position
    • Key switch contacts worn so the platform position is not recognised
    • Red emergency stop pushed in at the platform or ground controls
    • Key switch wiring or connector loose at the ground control box

    Checks

    1. 1Turn the key switch to platform and check the LCD or LED changes from CH to the normal display.
    2. 2Make sure both red emergency stop buttons are pulled out; a pushed-in stop can make the controls fall back to chassis mode.
    3. 3Meter the key switch in each position; the circuit for the selected position should read closed and the other open.
    4. 4Open the ground control box and check the key switch wires and connector are seated and not corroded.
    5. 5Replace the key switch if the display still shows CH with the key in the platform position.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie CHrgCharger interlock

    The battery charger is connected to AC power, so machine functions are limited until it is unplugged.· Other
    Info

    Causes

    • Charger plugged into an AC supply
    • Charger interlock input stuck active
    • Charger interlock wire shorted at the ground control box
    • Charger output wiring faulty

    Checks

    1. 1Unplug the charger from AC power and confirm the display returns to normal after a key cycle.
    2. 2If CHrg stays with the charger unplugged, check the interlock input wiring at the charger and at the ground control box.
    3. 3Measure the interlock input with the charger disconnected; it should read open, not battery voltage.
    4. 4Check the charger output cable and its connector for damage that could hold the input active.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie FLHtLimited lift height cleared

    The operator has cleared the maximum working height limit that LoHt had set.· Shorted high
    Info

    Causes

    • Operator cleared the limit on purpose
    • Height limit setting changed

    Checks

    1. 1Confirm the limit was cleared on purpose.
    2. 2Reset the working height limit if it should be active.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Genie LdLifting disabled

    Lift is blocked because the outriggers are not fully retracted, auto level has not finished, an outrigger lost ground contact, or a level sensor reports the machine is not level.· Real condition
    Info

    Causes

    • Outriggers extended or the auto level cycle not finished
    • An outrigger pad lost ground contact on soft ground
    • Outrigger level sensor reading off level
    • Outrigger position sensor or its connector faulty

    Checks

    1. 1Finish the outrigger auto level cycle and wait for the all-clear before trying to lift.
    2. 2Check every outrigger pad is pressing firmly on the ground and none is hanging.
    3. 3Retract the outriggers fully before driving and confirm the stowed indicator on the controls.
    4. 4Check both level sensors read level on a flat surface; compare with a spirit level on the chassis.
    5. 5Inspect the outrigger sensor connectors for water and run the outrigger calibration if C029 is also active.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Genie LLOff level

    The tilt sensor reports the chassis is on a slope beyond the allowed limit while the platform is raised.· Other
    Info

    Causes

    • Machine parked or driven onto a slope, soft ground or one raised wheel
    • Universal tilt sensor (UTS) mounted loose or out of calibration after a repair
    • Corroded or loose tilt sensor connector
    • Tilt sensor failed and reading off level on flat ground

    Checks

    1. 1Lower the platform fully and move the machine to firm, level ground, then raise again to see whether LL returns.
    2. 2Put a spirit level on the chassis next to the tilt sensor to confirm the machine really is level before blaming the sensor.
    3. 3Check the tilt sensor sits flat on its bracket and the mounting bolts are tight; a tilted sensor reads off level on flat ground.
    4. 4Unplug and inspect the tilt sensor connector for water or green corrosion; reseat it and clean the pins.
    5. 5If the machine is level and the code stays, run the level sensor calibration on a known flat surface, then replace the sensor if it will not calibrate.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie LoHtLift height limited

    The platform has reached the working height limit, or the operator switched the limit on, on CE and Australian models.· Other
    Info

    Causes

    • Maximum working height reached for the selected mode
    • Height limit selected by the operator
    • Height sensor reading higher than the real height
    • Height limit switch stuck closed

    Checks

    1. 1Lower the platform a little and see if the message clears; reaching the limit is normal behaviour.
    2. 2Check the setting in the operator's manual for how the height limit is switched on or off.
    3. 3If LoHt appears well below the limit, read the height sensor value on the service screen against the real platform height.
    4. 4Recalibrate the platform height sensor if the reading is wrong, and replace it if the reading is erratic.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie ndNo drive

    Drive is disabled because the pothole guards did not deploy or the pothole switch reports a problem.· Other
    Check soon

    Causes

    • Pothole guards not fully down because of debris or a bent guard
    • Pothole limit switch faulty or out of adjustment
    • Wiring or connector problem at the pothole switch
    • Guard pivot or return spring seized

    Checks

    1. 1Lower the platform fully and try drive again; the guards only deploy when the platform is stowed.
    2. 2Check each guard pivot and spring by hand with the platform lowered; they should move freely.
    3. 3Meter the pothole switch while moving the guard; it should change state at the same point on both sides.
    4. 4Read the service screen or LED for F005 or PHS at the same time, which point to the switch circuit.
    5. 5Adjust the switch gap per the manual, or replace the switch if its output does not change cleanly.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie ObSObstruction

    The contact alarm (obstruction sensor) was triggered and motion is blocked until the machine is moved away.· Real condition
    Info

    Causes

    • Platform, guard rail or chassis pressing against an object
    • Contact alarm bar or switch stuck
    • Contact alarm switch connector corroded
    • Contact alarm wiring shorted at the base

    Checks

    1. 1Move the machine away from the obstruction using the allowed direction; the message should clear.
    2. 2Check the contact alarm bar or switch moves freely and returns fully, without debris holding it in.
    3. 3Meter the contact switch with it free; it should read open or closed as the manual specifies, not stuck.
    4. 4Inspect the switch connector and harness for water and chafing; reseat the plug.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Genie OHLOutdoor height restriction

    The machine is limited by the outdoor height restriction for the work being done.· Real condition
    Info

    Causes

    • Outdoor height restriction active
    • Option setting changed

    Checks

    1. 1Check that the restriction is meant to be active.
    2. 2Change the outdoor height setting only as the manual allows.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Genie OLPlatform overload

    Platform load is above the rated capacity on CE and Australian models.· Real condition
    Stop now

    Causes

    • Too much weight or material on the platform
    • Overload pressure transducer on the lift cylinder out of calibration or drifting
    • Transducer connector or harness damaged
    • Hydraulic pressure spike from a binding scissor arm raising the transducer reading

    Checks

    1. 1Take everything off the platform and compare the load with the capacity plate; an empty platform should clear OL after a key cycle.
    2. 2Lower the platform fully and cycle the key switch off and on; OL that returns on an empty platform points to the transducer or its calibration.
    3. 3Inspect the load-sense transducer connector and wires at the lift cylinder; look for a pinched or oil-soaked cable.
    4. 4On the service screen read the overload value with the platform empty and stowed; it should sit at the calibrated zero and not drift as you raise.
    5. 5Run the platform overload calibration, and replace the transducer if the reading will not settle or changes when the cable is moved.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Genie PHSPothole guard stuck

    The pothole guards did not drop, or did not clear when the platform was lowered, so the controller blocks drive.· Other
    Check soon

    Causes

    • Pothole guard bar jammed by debris, a bent guard or a seized pivot
    • Pothole limit switch out of adjustment or stuck
    • Switch wire or connector damaged under the chassis
    • Pothole switch shorted, which also sets F005

    Checks

    1. 1Look under the chassis around each pothole guard for mud, debris or bent metal that stops it dropping.
    2. 2Raise and lower the platform while watching both guards; they should swing down together and spring back freely.
    3. 3Check the limit switch gap and roller arm against the manual and test the switch with a meter; it should change state cleanly as the guard moves.
    4. 4Inspect the switch connector and wires along the chassis for chafing; reseat the plug.
    5. 5If F005 shows as well, treat it as a shorted switch circuit and test with the switch unplugged; replace the switch if it is faulty.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Read the indicator on the platform display and match it to the section below before testing anything.
  2. 2Move the machine to level ground, unplug the charger or remove the obstruction as the code describes.
  3. 3Reduce the load on the platform to the rated capacity for an overload indication.
  4. 4If the indicator stays with the condition cleared, check the related sensor or switch circuit.

Causes

  • Machine on a slope or outriggers not fully retracted
  • Platform load above rated capacity
  • Charger connected, brakes released by hand or obstruction sensor triggered
  • Pothole guards not deployed or not cleared

Most common here: real condition (4 of 12)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: The function named by the indicator is blocked until the condition is cleared; no repair is needed for most of them.

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.