Develon · Fuel system
Develon Common rail and fuel pressure control fault codes
Codes for the rail pressure sensor, the metering valve or pressure regulator, the high-pressure pump and low-pressure fuel supply. The controller compares commanded and actual rail pressure.
Where this code shows
Switch the key on and open the monitor fault or service menu on the gauge panel to see active codes.
What do these codes mean?
Develon codes E000129 to E520203 are all about the common rail and fuel pressure control. 12 need an immediate stop. Start with this check: check the fuel filter, water separator and lift pump flow first.
How urgent are they?
All 12 codes here mean stop now.
- Stop now12
What should I check first?
Check the fuel filter, water separator and lift pump flow first.
Shared checks12 of 12
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Develon E000129Rail pressure sensor
The rail pressure sensor reports the fuel pressure in the common rail. With the signal missing or out of range the controller cannot hold rail pressure, so the engine may start hard, lose power or shut down.· OtherOtherStop nowCauses
- Failed rail pressure sensor
- Lost 5 V supply or ground
- Fuel leak or air in the fuel line
- Weak high-pressure pump
Checks
- 1Check the fuel filter and low-pressure supply first.
- 2Check the 5 V supply and ground at the rail sensor connector.
- 3Compare actual and commanded rail pressure while cranking and at idle.
- 4Inspect high-pressure fittings and return lines for leaks.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E000157CP metering unit
Same failure as E000129 on the cp metering unit, a different part of the same kind as the rail pressure sensor. Specific to this code: the table names it 'CP metering unit'. The Cummins engine table words this code as "Injector metering rail 1 press. sensor circuit"; the Isuzu engine table words this code as "Common Rail Pressure Sensor Fault", so confirm against the table for your engine.· OtherOtherStop nowCauses
- Fault in the cp metering unit or its wiring
- Any cause listed under E000129
Checks
- 1Check the cp metering unit connector and wiring first, then follow the checks listed under E000129.
- 2Clear the code and confirm whether E000157 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E000633Fueling actuator #1 circuit error
Same failure as E000129 on the fueling actuator #1 circuit error, a different part of the same kind as the rail pressure sensor. Specific to this code: the table names it 'fueling actuator #1 circuit error'. The Isuzu engine table words this code as "Pressure Limiter Open", so confirm against the table for your engine.· OtherOtherStop nowCauses
- Fault in the fueling actuator #1 circuit error or its wiring
- Any cause listed under E000129
Checks
- 1Check the fueling actuator #1 circuit error connector and wiring first, then follow the checks listed under E000129.
- 2Clear the code and confirm whether E000633 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E001075Electric lift pump control signal for E/G fuel
Same failure as E000129 on the electric lift pump control signal for e/g fuel, a different part of the same kind as the rail pressure sensor. Specific to this code: the table names it 'Electric lift pump control signal for E/G fuel'.· OtherOtherStop nowCauses
- Fault in the electric lift pump control signal for e/g fuel or its wiring
- Any cause listed under E000129
Checks
- 1Check the electric lift pump control signal for e/g fuel connector and wiring first, then follow the checks listed under E000129.
- 2Clear the code and confirm whether E001075 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E001239Common Rail Pressure Fault (Lack of Feed 1)
Same failure as E000129 on the common rail pressure fault (lack of feed 1), a different part of the same kind as the rail pressure sensor. Specific to this code: the table names it 'Common Rail Pressure Fault (Lack of Feed 1)'.· OtherOtherStop nowCauses
- Fault in the common rail pressure fault (lack of feed 1) or its wiring
- Any cause listed under E000129
Checks
- 1Check the common rail pressure fault (lack of feed 1) connector and wiring first, then follow the checks listed under E000129.
- 2Clear the code and confirm whether E001239 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E001240Common Rail Pressure Fault (Lack of Feed 2)
Same failure as E000129 on the common rail pressure fault (lack of feed 2), a different part of the same kind as the rail pressure sensor. Specific to this code: the table names it 'Common Rail Pressure Fault (Lack of Feed 2)'.· OtherOtherStop nowCauses
- Fault in the common rail pressure fault (lack of feed 2) or its wiring
- Any cause listed under E000129
Checks
- 1Check the common rail pressure fault (lack of feed 2) connector and wiring first, then follow the checks listed under E000129.
- 2Clear the code and confirm whether E001240 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E001347Fuel pump pressurizing assembly 1
Same failure as E000129 on the fuel pump pressurizing assembly 1, a different part of the same kind as the rail pressure sensor. Specific to this code: the table names it 'Fuel pump pressurizing assembly 1'. The Isuzu engine table words this code as "PCV 1 Drive System Fault", so confirm against the table for your engine.· OtherOtherStop nowCauses
- Fault in the fuel pump pressurizing assembly 1 or its wiring
- Any cause listed under E000129
Checks
- 1Check the fuel pump pressurizing assembly 1 connector and wiring first, then follow the checks listed under E000129.
- 2Clear the code and confirm whether E001347 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E001348PCV 2 Drive System Fault
Same failure as E000129 on the pcv 2 drive system fault, a different part of the same kind as the rail pressure sensor. Specific to this code: the table names it 'PCV 2 Drive System Fault'.· OtherOtherStop nowCauses
- Fault in the pcv 2 drive system fault or its wiring
- Any cause listed under E000129
Checks
- 1Check the pcv 2 drive system fault connector and wiring first, then follow the checks listed under E000129.
- 2Clear the code and confirm whether E001348 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E001381Fuel Filter Clogging Sensor Fault
Same failure as E000129 on the fuel filter clogging sensor fault, a different part of the same kind as the rail pressure sensor. Specific to this code: the table names it 'Fuel Filter Clogging Sensor Fault'.· Real conditionReal conditionStop nowCauses
- Fault in the fuel filter clogging sensor fault or its wiring
- Any cause listed under E000129
Checks
- 1Check the fuel filter clogging sensor fault connector and wiring first, then follow the checks listed under E000129.
- 2Clear the code and confirm whether E001381 returns on its own.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Develon E005465Pressure control regulator
Same failure as E000129 on the pressure control regulator, a different part of the same kind as the rail pressure sensor. Specific to this code: the table names it 'Pressure control regulator'.· OtherOtherStop nowCauses
- Fault in the pressure control regulator or its wiring
- Any cause listed under E000129
Checks
- 1Check the pressure control regulator connector and wiring first, then follow the checks listed under E000129.
- 2Clear the code and confirm whether E005465 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E520196Rail pressure monitoring
Same failure as E000129 on the rail pressure monitoring, a different part of the same kind as the rail pressure sensor. Specific to this code: the table names it 'Rail pressure monitoring'.· OtherOtherStop nowCauses
- Fault in the rail pressure monitoring or its wiring
- Any cause listed under E000129
Checks
- 1Check the rail pressure monitoring connector and wiring first, then follow the checks listed under E000129.
- 2Clear the code and confirm whether E520196 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E520203Monitoring of PRV
Same failure as E000129 on the monitoring of prv, a different part of the same kind as the rail pressure sensor. Specific to this code: the table names it 'Monitoring of PRV'.· OtherOtherStop nowCauses
- Fault in the monitoring of prv or its wiring
- Any cause listed under E000129
Checks
- 1Check the monitoring of prv connector and wiring first, then follow the checks listed under E000129.
- 2Clear the code and confirm whether E520203 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Check the fuel filter, water separator and lift pump flow first.
- 2Compare actual and commanded rail pressure in the diagnostic tool.
- 3Inspect the fuel lines and fittings for leaks and air ingress.
- 4Measure sensor supply and signal, and coil resistance of the metering valve.
Causes
- Failed pressure sensor or metering valve
- Air or restriction in low-pressure fuel supply
- Fuel leak or worn high-pressure pump
When to stop
You'll notice: Hard starting, low power or engine shutdown; the lamp lights and rail pressure codes are stored.
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
