EF Logo

Deutz · Starting and preheat

Deutz Fault Code SPN 729 FMI 3

Engine - Preheating relay - Voltage above normal or shorted to high source

What does Deutz code SPN 729 FMI 3 mean?

The EMR4 sees the output for the preheating relay (in the preheat circuit (glow plug or grid heater) controlled by the EMR4) at a voltage above normal, as if the circuit is shorted to the battery supply. Urgency: check soon - the machine may derate or limit a function. Check first: with the EMR4 unplugged, measure the output wire to battery positive; it should be open.

FaultCheckSPN 729FMI 3Deutz · Starting and preheat
FMI 3
Voltage above normal or shorted high

Can I keep running with it?

Check soon

The machine may derate or limit a function. Find the cause before the next shift.

What should I check first?

With the EMR4 unplugged, measure the output wire to battery positive; it should be open

Then 5 more checks
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug.

Checks

0 of 6 done

Causes

  • Output wire shorted to battery positive
  • Preheating relay shorted internally
  • Relay coil connector corroded
  • Harness insulation worn through where it rubs on a bracket, letting the wire touch a live supply

How it failed

You'll notice: Expect a warning lamp; the engine may start hard in cold weather and smoke as the preheat does not work, or the preheat lamp behaves oddly.

Shorted highRead from FMI 3: voltage above normal or shorted high

The signal sits at or near the supply voltage - more than a working sensor can send.

ControllerPartSupplySignalGround
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.
Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good result
Open circuit (OL) between them. Any low reading is the short.

When to stop

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Same part, other failures: Actuator relays, starter circuit and glow plug control

7 other codes on this part are also shorted high (SPN 677 FMI 3, SPN 523913 FMI 3, SPN 523914 FMI 3, SPN 523924 FMI 3 and more). When they show together, start at the wiring and connector they share.

Show the other 16 codes
All 25 Actuator relays, starter circuit and glow plug control codes on one page

Source

DEUTZ KWP-Codes EMR4 (KWPList EMR4 DE EN, Revision 2.0), page 9

This source lists SPN 729 FMI 3 and its meaning. The guidance on this page is general, not taken from it.

The source covers: Deutz engines with the EMR4 controller (the Deutz list applies to all EMR4 engine series, e.g. TCD 2.9, 3.6, 4.1, 6.1, 7.8 as fitted in machines).

Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.