EF Logo

Deutz · Injectors and combustion

Deutz Fault Code SPN 651 FMI 5

Engine - Injector 1 - Current below normal or open circuit

What does Deutz code SPN 651 FMI 5 mean?

The EMR4 measures too little current through the injector for cylinder 1, so the circuit is open. That cylinder gets no injection pulse and the controller logs the fault against injector 1. Urgency: stop now - shut down and fix before working on. Check first: with the key off, measure the cylinder 1 injector solenoid resistance at the injector terminals; an open coil reads infinite.

FaultStopSPN 651FMI 5Deutz · Injectors and combustion
FMI 5
Current below normal or open circuit

Can I keep running with it?

Stop now

Shut down and fix before working on. Running on risks damage or the machine locks out.

What should I check first?

With the key off, measure the cylinder 1 injector solenoid resistance at the injector terminals; an open coil reads infinite

Then 5 more checks
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug.

Checks

0 of 6 done

Causes

  • A broken wire or a pushed-back pin between the EMR4 and the cylinder 1 injector solenoid
  • Injector solenoid coil open inside the injector
  • Injector connector under the valve cover not fully latched
  • Valve cover through-connector corroded or damaged
1 more cause
  • Terminal pushed back or corroded in its connector so the circuit is open

How it failed

You'll notice: Engine runs on three cylinders or rough, with reduced power, vibration and a warning lamp; it may stall at idle.

Open circuitRead from FMI 5: current below normal or open circuit

No current flows, or the signal floats - a wire, pin or coil is broken.

ControllerPartSupplySignalGround
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.
Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good result
Near 0 Ω on each wire. The part reads its listed resistance, not OL.

When to stop

Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.

Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Same part, other failures: Injector solenoid circuits and banks

7 other codes on this part are also open circuit (SPN 652 FMI 5, SPN 653 FMI 5, SPN 654 FMI 5, SPN 655 FMI 5 and more). When they show together, start at the wiring and connector they share.

Show the other 13 codes
All 22 Injector solenoid circuits and banks codes on one page

Source

DEUTZ KWP-Codes EMR4 (KWPList EMR4 DE EN, Revision 2.0), page 10

This source lists SPN 651 FMI 5 and its meaning. The guidance on this page is general, not taken from it.

The source covers: Deutz engines with the EMR4 controller (the Deutz list applies to all EMR4 engine series, e.g. TCD 2.9, 3.6, 4.1, 6.1, 7.8 as fitted in machines).

Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.