Detroit · Fuel system
Detroit High-pressure fuel rail and quantity control valve fault codes
The high-pressure pump feeds the common rail, the MCM measures rail pressure with the rail pressure sensor and meters the delivery with the quantity control valve (QCV). Detroit uses these codes for sensor circuit faults, for pressure that is too low or too high, and for leakage in the high-pressure side.
Where to read it
Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.
What do these codes mean?
Detroit codes SPN 157 FMI 10 to SPN 521031 FMI 18 are all about the high-pressure fuel rail and quantity control valve. The most common failure type is real condition (7 of 23); 1 needs an immediate stop. Start with this check: check the low-pressure supply first: fuel filters, the water-in-fuel level and the supply pressure while cranking.
How urgent are they?
1 of 23 codes here means stop now; the other 22 can wait until the shift ends, but find the cause before the next one.
- Stop now1
- Check soon22
What should I check first?
Check the low-pressure supply first: fuel filters, the water-in-fuel level and the supply pressure while cranking.
Shared checks23 of 23
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Detroit SPN 157 FMI 10Under-Capacity in the High Pressure Circuit
Detroit lists SPN 157 FMI 10 as "Under-Capacity in the High Pressure Circuit". The MCM judged the fuel rail pressure sensor reading erratic or not plausible compared with other sensors or its own history. Rail pressure is the pressure in the common rail feeding all six injectors; the controller regulates it with the quantity control valve on the high-pressure pump.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting fuel rail pressure sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the fuel rail pressure sensor reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 157 FMI 15Rail Pressure Level For Injection Enabling Not Reached
Detroit lists SPN 157 FMI 15 as "Rail Pressure Level For Injection Enabling Not Reached". The MCM reports that the measured value itself is out of its normal range; the fuel rail pressure sensor may be correct and a real condition may exist. Rail pressure is the pressure in the common rail feeding all six injectors; the controller regulates it with the quantity control valve on the high-pressure pump.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the fuel rail pressure sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the fuel rail pressure sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 157 FMI 16Fuel Rail Pressure Too Low
The MCM found the fuel rail pressure lower than it demands for the running condition. This usually points to a fuel supply or high-pressure leak problem, and the engine may lose power or fail to start.· Real conditionReal conditionStop nowCauses
- Restricted fuel filter, air in the fuel or a weak lift pump starving the high-pressure pump
- Leaking injector or a leaking high-pressure fitting
- Quantity control valve or the high-pressure pump not delivering
- Rail pressure sensor reading low because of drift or wiring faults
Checks
- 1Replace or inspect the fuel filters and check the fuel supply pressure at the inlet of the high-pressure pump.
- 2Look for external fuel leaks at the rail, the lines and the pump while the engine is cranked.
- 3Read actual versus desired rail pressure while cranking in the tool; a slow rise points to the pump or a leak.
- 4Check the QCV connector and wiring and watch the QCV command in the tool.
- 5Run the injector cut-out tests to find a leaking injector before condemning the pump.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 157 FMI 17Minimum Rail Pressure Not Achieved While the Engine is Cranking
Detroit lists SPN 157 FMI 17 as "Minimum Rail Pressure Not Achieved While the Engine is Cranking". The MCM reports that the measured value itself is out of its normal range; the fuel rail pressure sensor may be correct and a real condition may exist. Rail pressure is the pressure in the common rail feeding all six injectors; the controller regulates it with the quantity control valve on the high-pressure pump.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the fuel rail pressure sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the fuel rail pressure sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 157 FMI 18Fuel Rail Pressure High
Detroit lists SPN 157 FMI 18 as "Fuel Rail Pressure High". The MCM reports that the measured value itself is out of its normal range; the fuel rail pressure sensor may be correct and a real condition may exist. Rail pressure is the pressure in the common rail feeding all six injectors; the controller regulates it with the quantity control valve on the high-pressure pump.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the fuel rail pressure sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the fuel rail pressure sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 164 FMI 2Fuel Rail Pressure Drift High
Detroit lists SPN 164 FMI 2 as "Fuel Rail Pressure Drift High". The MCM judged the fuel rail pressure sensor reading erratic or not plausible compared with other sensors or its own history. The rail pressure sensor is mounted on the common rail and gives the controller the actual pressure that the quantity control valve is trying to hold.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting fuel rail pressure sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the fuel rail pressure sensor reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 164 FMI 3Fuel Rail Pressure Sensor Circuit Failed High (Open Circuit)
Detroit lists SPN 164 FMI 3 as "Fuel Rail Pressure Sensor Circuit Failed High (Open Circuit)". The MCM saw the fuel rail pressure sensor signal above its valid range. That usually means the signal wire is shorted to a supply voltage or is open at the sensor. The rail pressure sensor is mounted on the common rail and gives the controller the actual pressure that the quantity control valve is trying to hold.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to the 5 V supply or open between the fuel rail pressure sensor and the MCM
- The fuel rail pressure sensor has failed inside
Checks
- 1Unplug the fuel rail pressure sensor and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
- 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 164 FMI 4Fuel Rail Pressure Sensor Circuit Failed Low (Short to Ground)
Detroit lists SPN 164 FMI 4 as "Fuel Rail Pressure Sensor Circuit Failed Low (Short to Ground)". The MCM saw the fuel rail pressure sensor signal below its valid range. That usually means the signal wire is shorted to ground or the sensor has failed. The rail pressure sensor is mounted on the common rail and gives the controller the actual pressure that the quantity control valve is trying to hold.· Shorted lowShorted lowCheck soonCauses
- Signal wire chafed against the engine and shorted to ground
- The fuel rail pressure sensor has failed inside or its supply wire is open
Checks
- 1Unplug the fuel rail pressure sensor and check whether the signal rises; if it stays low the harness is shorted to ground.
- 2Check the sensor supply at the connector with the key on and trace it back to the MCM if it is missing.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 164 FMI 5Fuel Rail Pressure Sensor Circuit Open or a Stuck-in-Range Sensor
Same failure as SPN 164 FMI 3 ("Fuel Rail Pressure Sensor Circuit Failed High (Open Circuit)") on a sibling part: Detroit lists SPN 164 FMI 5 as "Fuel Rail Pressure Sensor Circuit Open or a Stuck-in-Range Sensor". The rail pressure sensor is mounted on the common rail and gives the controller the actual pressure that the quantity control valve is trying to hold.· Open circuitOpen circuitCheck soonCauses
- The causes listed under SPN 164 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 164 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Detroit SPN 164 FMI 15Rail Pressure Deviation Greater than 200 Bar While Under Load
Detroit lists SPN 164 FMI 15 as "Rail Pressure Deviation Greater than 200 Bar While Under Load". The MCM reports that the measured value itself is out of its normal range; the fuel rail pressure sensor may be correct and a real condition may exist. The rail pressure sensor is mounted on the common rail and gives the controller the actual pressure that the quantity control valve is trying to hold.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the fuel rail pressure sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the fuel rail pressure sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 164 FMI 20Rail Pressure Sensor Drift High
Same failure as SPN 164 FMI 2 ("Fuel Rail Pressure Drift High") on a sibling part: Detroit lists SPN 164 FMI 20 as "Rail Pressure Sensor Drift High". The rail pressure sensor is mounted on the common rail and gives the controller the actual pressure that the quantity control valve is trying to hold.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 164 FMI 2, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 164 FMI 2, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 164 FMI 21Fuel Rail Pressure Sensor Drift Low
Detroit lists SPN 164 FMI 21 as "Fuel Rail Pressure Sensor Drift Low". The MCM found the fuel rail pressure sensor value drifted away from what the engine state says it should be. The rail pressure sensor is mounted on the common rail and gives the controller the actual pressure that the quantity control valve is trying to hold.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Sensor aged, contaminated or out of calibration
- A real fault in the system being measured
Checks
- 1Compare the fuel rail pressure sensor reading with a reference gauge or thermometer with the engine off and cold.
- 2Check the system around the fuel rail pressure sensor for leaks, restrictions or contamination.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 1077 FMI 3Quantity Control Valve (QCV) Circuit Failed High
Detroit lists SPN 1077 FMI 3 as "Quantity Control Valve (QCV) Circuit Failed High". The MCM saw the fuel rail pressure sensor signal above its valid range. That usually means the signal wire is shorted to a supply voltage or is open at the sensor. The quantity control valve (QCV) on the high-pressure pump meters the fuel going into the rail; its current is controlled by the MCM.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to the 5 V supply or open between the fuel rail pressure sensor and the MCM
- The fuel rail pressure sensor has failed inside
Checks
- 1Unplug the fuel rail pressure sensor and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
- 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 1077 FMI 4Quantity Control Valve (QCV) Circuit Failed Low
Same failure as SPN 164 FMI 4 ("Fuel Rail Pressure Sensor Circuit Failed Low (Short to Ground)") on a sibling part: Detroit lists SPN 1077 FMI 4 as "Quantity Control Valve (QCV) Circuit Failed Low". The quantity control valve (QCV) on the high-pressure pump meters the fuel going into the rail; its current is controlled by the MCM.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 164 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 164 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 1077 FMI 5Quantity Control Valve Current Too Low
Detroit lists SPN 1077 FMI 5 as "Quantity Control Valve Current Too Low". The MCM detected an open circuit on the fuel rail pressure sensor line, so the signal floats or is missing. The quantity control valve (QCV) on the high-pressure pump meters the fuel going into the rail; its current is controlled by the MCM.· Open circuitOpen circuitCheck soonCauses
- Broken wire or a pushed-out pin in the fuel rail pressure sensor connector
- Corroded terminal or a failed sensor
Checks
- 1Check continuity of every wire between the fuel rail pressure sensor connector and the MCM connector.
- 2Wiggle the harness and connector while watching the live value for dropouts.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Detroit SPN 1077 FMI 6Quantity Control Valve, Desired Current Does Not Match Actual Current
Detroit lists SPN 1077 FMI 6 as "Quantity Control Valve, Desired Current Does Not Match Actual Current". The MCM saw the fuel rail pressure sensor signal below its valid range. That usually means the signal wire is shorted to ground or the sensor has failed. The quantity control valve (QCV) on the high-pressure pump meters the fuel going into the rail; its current is controlled by the MCM.· Shorted lowShorted lowCheck soonCauses
- Signal wire chafed against the engine and shorted to ground
- The fuel rail pressure sensor has failed inside or its supply wire is open
Checks
- 1Unplug the fuel rail pressure sensor and check whether the signal rises; if it stays low the harness is shorted to ground.
- 2Check the sensor supply at the connector with the key on and trace it back to the MCM if it is missing.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 1077 FMI 14Internal or External Leakage of the High Pressure Fuel System (Too High, Leak Down Test)
Detroit lists SPN 1077 FMI 14 as "Internal or External Leakage of the High Pressure Fuel System (Too High, Leak Down Test)". The MCM judged the fuel rail pressure sensor reading erratic or not plausible compared with other sensors or its own history. The quantity control valve (QCV) on the high-pressure pump meters the fuel going into the rail; its current is controlled by the MCM.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting fuel rail pressure sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the fuel rail pressure sensor reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 5323 FMI 13Excessive Time to Enter Closed Loop Fuel Pressure Control
Detroit lists SPN 5323 FMI 13 as "Excessive Time to Enter Closed Loop Fuel Pressure Control". The MCM found the fuel rail pressure sensor value drifted away from what the engine state says it should be. After start the MCM must enter closed-loop control of rail pressure within a set time; taking too long suggests a pressure build problem.· Part or controllerPart or controllerCheck soonCauses
- Sensor aged, contaminated or out of calibration
- A real fault in the system being measured
Checks
- 1Compare the fuel rail pressure sensor reading with a reference gauge or thermometer with the engine off and cold.
- 2Check the system around the fuel rail pressure sensor for leaks, restrictions or contamination.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 5418 FMI 3Quantity Control Valve High Side Error
Detroit lists SPN 5418 FMI 3 as "Quantity Control Valve High Side Error". The MCM saw the fuel rail pressure sensor signal above its valid range. That usually means the signal wire is shorted to a supply voltage or is open at the sensor. The QCV high side and low side outputs are monitored separately for faults.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to the 5 V supply or open between the fuel rail pressure sensor and the MCM
- The fuel rail pressure sensor has failed inside
Checks
- 1Unplug the fuel rail pressure sensor and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
- 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 5418 FMI 4Quantity Control Valve Low Side Error
Detroit lists SPN 5418 FMI 4 as "Quantity Control Valve Low Side Error". The MCM saw the fuel rail pressure sensor signal below its valid range. That usually means the signal wire is shorted to ground or the sensor has failed. The QCV high side and low side outputs are monitored separately for faults.· Shorted lowShorted lowCheck soonCauses
- Signal wire chafed against the engine and shorted to ground
- The fuel rail pressure sensor has failed inside or its supply wire is open
Checks
- 1Unplug the fuel rail pressure sensor and check whether the signal rises; if it stays low the harness is shorted to ground.
- 2Check the sensor supply at the connector with the key on and trace it back to the MCM if it is missing.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 5571 FMI 7Pressure Limiting Valve Staying Open
Detroit lists SPN 5571 FMI 7 as "Pressure Limiting Valve Staying Open". The MCM judged the fuel rail pressure sensor reading erratic or not plausible compared with other sensors or its own history. The pressure limiting valve on the rail opens to protect the rail; if it stays open the pressure cannot build.· Part or controllerPart or controllerCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting fuel rail pressure sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the fuel rail pressure sensor reading with a second reference such as a gauge or another sensor on the engine.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 521031 FMI 16Fuel Rail Pressure Too Low
Same failure as SPN 157 FMI 16 ("Fuel Rail Pressure Too Low") on a sibling part: Detroit lists SPN 521031 FMI 16 as "Fuel Rail Pressure Too Low". Rail pressure too low or too high is flagged here as separate FMI entries.· Real conditionReal conditionCheck soonCauses
- The causes listed under SPN 157 FMI 16, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 157 FMI 16, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 521031 FMI 18Fuel Rail Pressure High
Same failure as SPN 157 FMI 18 ("Fuel Rail Pressure High") on a sibling part: Detroit lists SPN 521031 FMI 18 as "Fuel Rail Pressure High". Rail pressure too low or too high is flagged here as separate FMI entries.· Real conditionReal conditionCheck soonCauses
- The causes listed under SPN 157 FMI 18, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 157 FMI 18, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Shared checks
Checks, in order
- 1Check the low-pressure supply first: fuel filters, the water-in-fuel level and the supply pressure while cranking.
- 2Read the actual and desired rail pressure while cranking and at idle to see whether the pump or the sensor is wrong.
- 3Inspect the rail pressure sensor and QCV connectors and wiring for oil, chafing and bent pins.
- 4Look for fuel leaks at the rail, the high-pressure lines and the pump, and check the oil for fuel.
- 5Run the injector cut-out and leak tests in the tool to isolate a leaking injector before replacing the pump.
Causes
- Low-pressure supply problem such as a restricted filter, air in the fuel or a weak lift pump
- Leaking injector, rail fitting or pressure limiting valve in the high-pressure circuit
- Rail pressure sensor or QCV connector damaged, or harness chafed
- Worn high-pressure pump behind a pressure-not-reached code
Most common here: real condition (7 of 23)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: Hard starting, long cranking, rough running or a loss of power are typical, and the engine may derate or not start at all.
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Detroit Diesel DD15 Gen 5 (2023) Fault Codes List, Diesel Repair (SPN/FMI with Detroit descriptions)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
