Detroit · Fuel system
Detroit Low-pressure fuel supply, filter and water in fuel fault codes
The low-pressure fuel side includes the lift pump, the fuel filters, the water-in-fuel sensors, the supply fuel temperature sensor and the fuel level input. Detroit uses these codes for filter service warnings, water in the fuel and the sensors that watch this circuit.
Where to read it
Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.
What do these codes mean?
Detroit codes SPN 94 FMI 2 to SPN 6301 FMI 15 are all about the low-pressure fuel supply, filter and water in fuel. The most common failure type is real condition (9 of 25); none needs an immediate stop. Start with this check: drain the water separator and check the fuel for water, wax or contamination.
How urgent are they?
None of the 25 codes here means stop now; all 25 can wait until the shift ends, but find the cause before the next one.
- Check soon25
What should I check first?
Drain the water separator and check the fuel for water, wax or contamination.
Shared checks25 of 25
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Detroit SPN 94 FMI 2Low Side Fuel Pressure Not Plausible
Detroit lists SPN 94 FMI 2 as "Low Side Fuel Pressure Not Plausible". The MCM judged the fuel supply sensor reading erratic or not plausible compared with other sensors or its own history. Low-side fuel pressure is the pressure between the tank and the high-pressure pump, so a weak lift pump, a clogged filter or an air leak on the suction side shows here first.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting fuel supply sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the fuel supply sensor reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 94 FMI 3Low Pressure Pump Output (LPPO) Circuit Failed High
Detroit lists SPN 94 FMI 3 as "Low Pressure Pump Output (LPPO) Circuit Failed High". The MCM saw the fuel supply sensor signal above its valid range. That usually means the signal wire is shorted to a supply voltage or is open at the sensor. Low-side fuel pressure is the pressure between the tank and the high-pressure pump, so a weak lift pump, a clogged filter or an air leak on the suction side shows here first.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to the 5 V supply or open between the fuel supply sensor and the MCM
- The fuel supply sensor has failed inside
Checks
- 1Unplug the fuel supply sensor and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
- 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 94 FMI 4Low Side Fuel Pressure Sensor Circuit Failed Low
Detroit lists SPN 94 FMI 4 as "Low Side Fuel Pressure Sensor Circuit Failed Low". The MCM saw the fuel supply sensor signal below its valid range. That usually means the signal wire is shorted to ground or the sensor has failed. Low-side fuel pressure is the pressure between the tank and the high-pressure pump, so a weak lift pump, a clogged filter or an air leak on the suction side shows here first.· Shorted lowShorted lowCheck soonCauses
- Signal wire chafed against the engine and shorted to ground
- The fuel supply sensor has failed inside or its supply wire is open
Checks
- 1Unplug the fuel supply sensor and check whether the signal rises; if it stays low the harness is shorted to ground.
- 2Check the sensor supply at the connector with the key on and trace it back to the MCM if it is missing.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 94 FMI 11Low Side Fuel Pressure Not Plausible
Same failure as SPN 94 FMI 2 ("Low Side Fuel Pressure Not Plausible") on a sibling part: Detroit lists SPN 94 FMI 11 as "Low Side Fuel Pressure Not Plausible". Low-side fuel pressure is the pressure between the tank and the high-pressure pump, so a weak lift pump, a clogged filter or an air leak on the suction side shows here first.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 94 FMI 2, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 94 FMI 2, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 94 FMI 15Fuel Filter Service Warning
Detroit lists SPN 94 FMI 15 as "Fuel Filter Service Warning". The MCM reports that the measured value itself is out of its normal range; the fuel supply sensor may be correct and a real condition may exist. Low-side fuel pressure is the pressure between the tank and the high-pressure pump, so a weak lift pump, a clogged filter or an air leak on the suction side shows here first.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the fuel supply sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the fuel supply sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 94 FMI 16Fuel Filter Replacement Required
Detroit lists SPN 94 FMI 16 as "Fuel Filter Replacement Required". The MCM reports that the measured value itself is out of its normal range; the fuel supply sensor may be correct and a real condition may exist. Low-side fuel pressure is the pressure between the tank and the high-pressure pump, so a weak lift pump, a clogged filter or an air leak on the suction side shows here first.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the fuel supply sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the fuel supply sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 96 FMI 2Fuel Tank Level Sensor Stuck in Position
Detroit lists SPN 96 FMI 2 as "Fuel Tank Level Sensor Stuck in Position". The MCM judged the fuel supply sensor reading erratic or not plausible compared with other sensors or its own history. The fuel level input comes from the tank sender through the vehicle network and is used for the dash gauge and for fuel-related protections.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting fuel supply sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the fuel supply sensor reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 96 FMI 13Fuel Level Sensor Missing or Not Available
Detroit lists SPN 96 FMI 13 as "Fuel Level Sensor Missing or Not Available". The MCM found the fuel supply sensor value drifted away from what the engine state says it should be. The fuel level input comes from the tank sender through the vehicle network and is used for the dash gauge and for fuel-related protections.· Part or controllerPart or controllerCheck soonCauses
- Sensor aged, contaminated or out of calibration
- A real fault in the system being measured
Checks
- 1Compare the fuel supply sensor reading with a reference gauge or thermometer with the engine off and cold.
- 2Check the system around the fuel supply sensor for leaks, restrictions or contamination.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 96 FMI 19Fuel Level Sensor Signal Error
Detroit lists SPN 96 FMI 19 as "Fuel Level Sensor Signal Error". The MCM lost the fuel supply sensor signal completely. The fuel level input comes from the tank sender through the vehicle network and is used for the dash gauge and for fuel-related protections.· Lost messageLost messageCheck soonCauses
- Signal path broken at the connector or the harness
- Failed sensor or module
Checks
- 1Check the connector and the power supply to the fuel supply sensor.
- 2Check the signal wire to the MCM for an open.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Detroit SPN 97 FMI 3Water-in-Fuel Circuit Failed High
Same failure as SPN 94 FMI 3 ("Low Pressure Pump Output (LPPO) Circuit Failed High") on a sibling part: Detroit lists SPN 97 FMI 3 as "Water-in-Fuel Circuit Failed High". The water-in-fuel sensor sits in the filter or water separator base and trips when water collects in the bowl; drain the bowl before testing the circuit.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 94 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 94 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 97 FMI 4Water-in-Fuel Circuit Failed Low
Same failure as SPN 94 FMI 4 ("Low Side Fuel Pressure Sensor Circuit Failed Low") on a sibling part: Detroit lists SPN 97 FMI 4 as "Water-in-Fuel Circuit Failed Low". The water-in-fuel sensor sits in the filter or water separator base and trips when water collects in the bowl; drain the bowl before testing the circuit.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 94 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 94 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 97 FMI 15Water-in-Fuel Warning
Detroit lists SPN 97 FMI 15 as "Water-in-Fuel Warning". The MCM reports that the measured value itself is out of its normal range; the fuel supply sensor may be correct and a real condition may exist. The water-in-fuel sensor sits in the filter or water separator base and trips when water collects in the bowl; drain the bowl before testing the circuit.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the fuel supply sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the fuel supply sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 97 FMI 16Water-in-Fuel Warning
Same failure as SPN 97 FMI 15 ("Water-in-Fuel Warning") on a sibling part: Detroit lists SPN 97 FMI 16 as "Water-in-Fuel Warning". The water-in-fuel sensor sits in the filter or water separator base and trips when water collects in the bowl; drain the bowl before testing the circuit.· Real conditionReal conditionCheck soonCauses
- The causes listed under SPN 97 FMI 15, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 97 FMI 15, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 97 FMI 31Water-in-Fuel Warning - Ignored
Detroit lists SPN 97 FMI 31 as "Water-in-Fuel Warning - Ignored". The MCM logged a condition on the fuel supply sensor; the title says what it measured. The water-in-fuel sensor sits in the filter or water separator base and trips when water collects in the bowl; drain the bowl before testing the circuit.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the fuel supply sensor watches
- Sensor or wiring fault
Checks
- 1Read the live value and compare it with a reference.
- 2Check the connector and wiring.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 174 FMI 0Supply Fuel Temperature Sensor Too High
Detroit lists SPN 174 FMI 0 as "Supply Fuel Temperature Sensor Too High". The MCM reports that the measured value itself is out of its normal range; the fuel supply sensor may be correct and a real condition may exist. Supply fuel temperature is read in the low-pressure circuit and corrects the fuel quantity for fuel density and protects the pump from hot fuel.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the fuel supply sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the fuel supply sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 174 FMI 3Supply Fuel Temperature Sensor Open Circuit
Detroit lists SPN 174 FMI 3 as "Supply Fuel Temperature Sensor Open Circuit". The MCM saw the fuel supply sensor signal above its valid range. That usually means the signal wire is shorted to a supply voltage or is open at the sensor. Supply fuel temperature is read in the low-pressure circuit and corrects the fuel quantity for fuel density and protects the pump from hot fuel.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to the 5 V supply or open between the fuel supply sensor and the MCM
- The fuel supply sensor has failed inside
Checks
- 1Unplug the fuel supply sensor and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
- 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 174 FMI 4Supply Fuel Temperature Sensor Short Circuit to Ground
Same failure as SPN 94 FMI 4 ("Low Side Fuel Pressure Sensor Circuit Failed Low") on a sibling part: Detroit lists SPN 174 FMI 4 as "Supply Fuel Temperature Sensor Short Circuit to Ground". Supply fuel temperature is read in the low-pressure circuit and corrects the fuel quantity for fuel density and protects the pump from hot fuel.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 94 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 94 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 174 FMI 11Fuel Temperature Sensor, General Temperature Plausibility Error
Same failure as SPN 94 FMI 2 ("Low Side Fuel Pressure Not Plausible") on a sibling part: Detroit lists SPN 174 FMI 11 as "Fuel Temperature Sensor, General Temperature Plausibility Error". Supply fuel temperature is read in the low-pressure circuit and corrects the fuel quantity for fuel density and protects the pump from hot fuel.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 94 FMI 2, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 94 FMI 2, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 174 FMI 14Fuel Temperature Sensor Signal Not Plausible
Same failure as SPN 94 FMI 2 ("Low Side Fuel Pressure Not Plausible") on a sibling part: Detroit lists SPN 174 FMI 14 as "Fuel Temperature Sensor Signal Not Plausible". Supply fuel temperature is read in the low-pressure circuit and corrects the fuel quantity for fuel density and protects the pump from hot fuel.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 94 FMI 2, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 94 FMI 2, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 174 FMI 17Fuel Temperature Sensor, Rise Too Slow
Detroit lists SPN 174 FMI 17 as "Fuel Temperature Sensor, Rise Too Slow". The MCM reports that the measured value itself is out of its normal range; the fuel supply sensor may be correct and a real condition may exist. Supply fuel temperature is read in the low-pressure circuit and corrects the fuel quantity for fuel density and protects the pump from hot fuel.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the fuel supply sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the fuel supply sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 5395 FMI 15Idle Fuel Quantity Out of Range
Detroit lists SPN 5395 FMI 15 as "Idle Fuel Quantity Out of Range". The MCM reports that the measured value itself is out of its normal range; the fuel supply sensor may be correct and a real condition may exist. The idle fuel quantity should stay within a normal band; out of range means an injector, pressure or air problem.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the fuel supply sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the fuel supply sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 5540 FMI 2Fuel Temperature Signal Not Plausible
Same failure as SPN 94 FMI 2 ("Low Side Fuel Pressure Not Plausible") on a sibling part: Detroit lists SPN 5540 FMI 2 as "Fuel Temperature Signal Not Plausible". The fuel temperature signal is compared with the other temperature signals for plausibility.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 94 FMI 2, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 94 FMI 2, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 6301 FMI 3Signal Range High Active for WIF Sensor 2
Same failure as SPN 94 FMI 3 ("Low Pressure Pump Output (LPPO) Circuit Failed High") on a sibling part: Detroit lists SPN 6301 FMI 3 as "Signal Range High Active for WIF Sensor 2". The second water-in-fuel sensor (WIF 2) is read separately from the first and gives a second water signal.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 94 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 94 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 6301 FMI 4Signal Range High Active for WIF Sensor 2
Same failure as SPN 94 FMI 3 ("Low Pressure Pump Output (LPPO) Circuit Failed High") on a sibling part: Detroit lists SPN 6301 FMI 4 as "Signal Range High Active for WIF Sensor 2". The second water-in-fuel sensor (WIF 2) is read separately from the first and gives a second water signal.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 94 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 94 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 6301 FMI 15Water In Fuel for WIF2
Detroit lists SPN 6301 FMI 15 as "Water In Fuel for WIF2". The MCM reports that the measured value itself is out of its normal range; the fuel supply sensor may be correct and a real condition may exist. The second water-in-fuel sensor (WIF 2) is read separately from the first and gives a second water signal.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the fuel supply sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the fuel supply sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Shared checks
Checks, in order
- 1Drain the water separator and check the fuel for water, wax or contamination.
- 2Inspect or replace the fuel filters if the service interval is overdue and measure the supply pressure.
- 3Check the fuel temperature, pressure and water-in-fuel sensor connectors for corrosion and bent pins.
- 4Test the signal wires for continuity and for shorts to ground or to the sensor supply.
- 5Check the tank pickup and the suction lines for air leaks and kinks.
Causes
- Plugged primary or secondary fuel filter
- Water in the fuel or a water separator that has not been drained
- Low-pressure pump output weak or its wiring faulty
- Sensor connector or wiring damage
Most common here: real condition (9 of 25)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: A fuel filter or water-in-fuel lamp, a power loss or hard starting; water in fuel can lead to a derate.
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Detroit Diesel DD15 Gen 5 (2023) Fault Codes List, Diesel Repair (SPN/FMI with Detroit descriptions)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
