EF Logo

Cummins · Starting aid

Cummins Starting aids and starter control fault codes

A grid heater or manifold heater warms the intake air for cold starting. A solenoid injects a metered amount of starting fluid into the intake in very cold weather.

More about these parts

The wait-to-start lamp tells the operator that the intake heater is active. The ECM drives the starter relay and monitors how long it cranks, and the transmission can allow or inhibit cranking.

FaultCheck383Cummins · Starting aids and starter control
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.

What do these codes mean?

Cummins codes 383 to 15696 are all about the starting aids and starter control. The most common failure type is shorted high (4 of 17); none needs an immediate stop. Start with this check: measure the heater element resistance with the power disconnected and compare it with the service manual.

How urgent are they?

None of the 17 codes here means stop now; 15 can wait until the shift ends, but find the cause before the next one; 2 are information only.

  • Check soon15
  • Info2

What should I check first?

Measure the heater element resistance with the power disconnected and compare it with the service manual

Shared checks

17 of 17

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Starter relay driver circuit3 codes

    • Cummins 584Starter relay driver circuit: Voltage high

      The ECM sees the starter relay driver pulled high, as if the circuit were shorted to supply or the relay return were open.· Shorted high
      Check soon

      Causes

      • Starter relay driver wire shorted to a switched power wire
      • Relay coil return open
      • Relay stuck closed

      Checks

      1. 1Pull the starter relay and see whether the starter stops cranking
      2. 2Measure the driver pin at the relay base with the key off for any voltage
      3. 3Check the starter relay coil return wire for continuity back to the ECM
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

    • Cummins 6261Starter relay driver circuit: Voltage high / shorted high

      The ECM sees the starter relay driver circuit drive circuit with voltage above the expected level.· Shorted high
      Check soon

      Causes

      • Output wire shorted to battery or a switched power feed
      • Open ground or return path on the component
      • Component winding failed or its connector damaged

      Checks

      1. 1Unplug the starter relay driver circuit connector, key on, and measure the output pin to ground; battery voltage with nothing connected points to a short to power
      2. 2Inspect the harness for a rubbed wire or damaged splice touching a power feed
      3. 3Measure the component resistance across its pins to rule out an open winding
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

      Source wording:Starter relay driver circuit - voltage high (shorted to a high source)

    • Cummins 6262Starter relay driver circuit: Voltage low / shorted low

      The ECM sees the starter relay driver circuit drive circuit with voltage below the expected level.· Shorted low
      Check soon

      Causes

      • Output wire shorted to ground or chafed through to the chassis
      • Component winding shorted internally
      • Connector corroded and bridging the pins

      Checks

      1. 1Unplug the starter relay driver circuit connector and measure the output pin to ground; a short here means the harness is at fault
      2. 2Measure the component resistance across its pins; a very low reading means a shorted winding
      3. 3Inspect the connector for moisture and bridged terminals
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:Starter relay driver circuit - voltage low (shorted to a low source)

  • Intake air heater circuit1 code

    • Cummins 2555Intake air heater circuit: Voltage high

      The ECM sees the intake heater control output high, which suggests a short to power or a heater relay that is stuck on.· Shorted high
      Check soon

      Causes

      • Heater relay contacts welded closed
      • Heater control wire shorted to a switched supply
      • Open return on the relay coil

      Checks

      1. 1Key off: check whether the heater still draws current or feels hot
      2. 2Pull the relay and check that the contacts are not stuck
      3. 3Measure the control wire at the relay base with the key on
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

  • Start enable device 1 circuit (ether injection)2 codes

    • Cummins 2738Start enable device 1 circuit (ether injection): Voltage high / shorted high

      The ECM sees the start enable device 1 circuit (ether injection) drive circuit with voltage above the expected level.· Shorted high
      Check soon

      Causes

      • Output wire shorted to battery or a switched power feed
      • Open ground or return path on the component
      • Component winding failed or its connector damaged

      Checks

      1. 1Unplug the start enable device 1 circuit (ether injection) connector, key on, and measure the output pin to ground; battery voltage with nothing connected points to a short to power
      2. 2Inspect the harness for a rubbed wire or damaged splice touching a power feed
      3. 3Measure the component resistance across its pins to rule out an open winding
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

      Source wording:Start enable device 1 circuit (ether injection) - voltage high (shorted to a high source)

    • Cummins 2739Start enable device 1 circuit (ether injection): Voltage low / shorted low

      The ECM sees the start enable device 1 circuit (ether injection) drive circuit with voltage below the expected level.· Shorted low
      Check soon

      Causes

      • Output wire shorted to ground or chafed through to the chassis
      • Component winding shorted internally
      • Connector corroded and bridging the pins

      Checks

      1. 1Unplug the start enable device 1 circuit (ether injection) connector and measure the output pin to ground; a short here means the harness is at fault
      2. 2Measure the component resistance across its pins; a very low reading means a shorted winding
      3. 3Inspect the connector for moisture and bridged terminals
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:Start enable device 1 circuit (ether injection) - voltage low (shorted to a low source)

  • Engine wait to start lamp4 codes

    • Cummins 3494Engine wait to start lamp: Mechanical fault or not responding

      The ECM commands the engine wait to start lamp but it does not respond as expected, or its movement is out of adjustment.· Part or controller
      Check soon

      Causes

      • Mechanism seized, sooted or blocked
      • Wear or incorrect adjustment of the linkage or part
      • Supply or return fault limiting its movement

      Checks

      1. 1Command the engine wait to start lamp in INSITE and watch whether it moves and returns
      2. 2Inspect the part and its linkage for sticking, debris or wear
      3. 3Check supply and return connections before replacing it
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

    • Cummins 3555Engine wait to start lamp: Abnormal update rate

      The ECM is not receiving fresh data for the engine wait to start lamp at the expected rate, so the value is late or has stopped updating.· Erratic or implausible
      Check soon

      Causes

      • Wiring or connector contact fault
      • Sending module offline or failing

      Checks

      1. 1Check the wiring and connector for loose terminals
      2. 2Look for related data link or module faults
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

    • Cummins 3556Engine wait to start lamp: Network data in error

      The ECM received the engine wait to start lamp over the data link but the message is flagged as invalid, so it cannot be used.· Lost message
      Check soon

      Causes

      • Sending module reporting an invalid value
      • Data link wiring or connector fault

      Checks

      1. 1Find which module sends the message and read its codes
      2. 2Check the data link wiring and connectors
      Module AModule BCAN HCAN L120 Ω120 Ω
      Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

      Meter test

      Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

      Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

      Source wording:Engine wait to start lamp - network data received in error

    • Cummins 4252Engine wait to start lamp: Condition exists

      The ECM sets this code when it recognises a defined condition for the engine wait to start lamp.· Other
      Info

      Causes

      • A monitor or protection condition that has been met
      • A related fault that set first

      Checks

      1. 1Read the code description and freeze-frame in INSITE for the exact condition
      2. 2Work the related active codes first, then recheck
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Read the code with the service tool and note which other codes are active with it.

      Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Engine starter mode over-crank protection1 code

    • Cummins 3737Engine starter mode over-crank protection: Condition exists

      The ECM sets this code when it recognises a defined condition for the engine starter mode over-crank protection.· Other
      Info

      Causes

      • A monitor or protection condition that has been met
      • A related fault that set first

      Checks

      1. 1Read the code description and freeze-frame in INSITE for the exact condition
      2. 2Work the related active codes first, then recheck
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Read the code with the service tool and note which other codes are active with it.

      Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Transmission engine crank enable2 codes

    • Cummins 8264Transmission engine crank enable: Out of calibration

      The ECM reports the transmission engine crank enable as out of calibration, meaning the value or setting it received does not match what it was programmed to expect.· Part or controller
      Check soon

      Causes

      • Parameter set for a feature that is not fitted
      • Wrong or outdated calibration in the ECM
      • Source module sending an invalid value

      Checks

      1. 1Compare the ECM parameters with the vehicle equipment
      2. 2Reflash the ECM with the correct calibration
      3. 3Read the source module for its own codes
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

    • Cummins 15696Transmission engine crank enable: Abnormal update rate

      The ECM is not receiving fresh data for the transmission engine crank enable at the expected rate.· Lost message
      Check soon

      Causes

      • Data link wiring fault or a poor connector contact
      • The module that sends the message is offline or failing
      • Power or ground problem at the sending module

      Checks

      1. 1Look for other modules reporting timeouts to find where the link is broken
      2. 2Check the data link wiring, connectors and terminators
      3. 3Read the sending module for its own codes
      Module AModule BCAN HCAN L120 Ω120 Ω
      Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

      Meter test

      Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

      Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Engine wait to start lamp data1 code

    • Cummins 11252Engine wait to start lamp data: Mechanical fault or not responding

      The ECM commands the engine wait to start lamp data but it does not respond as expected, or its movement is out of adjustment.· Part or controller
      Check soon

      Causes

      • Mechanism seized, sooted or blocked
      • Wear or incorrect adjustment of the linkage or part
      • Supply or return fault limiting its movement

      Checks

      1. 1Command the engine wait to start lamp data in INSITE and watch whether it moves and returns
      2. 2Inspect the part and its linkage for sticking, debris or wear
      3. 3Check supply and return connections before replacing it
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Other codes3 codes

    • Cummins 383Intake air heater circuit open circuit

      The ECM finds no current flowing in the intake air heater circuit when it commands it on, so the circuit is open or the load is unplugged.· Open circuit
      Check soon

      Causes

      • Intake air heater element burnt open
      • Heater relay not closing
      • Heavy cable loose at the heater terminal

      Checks

      1. 1In cold weather check the heater current or the warmth of the heater
      2. 2Measure the voltage on the heater terminal when commanded
      3. 3Check the intake heater relay and fuse for an open contact that mimics an open heater
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

      Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

    • Cummins 585Starter relay driver shorted low or driver voltage low

      The ECM drives the starter relay driver but sees its output pulled to ground.· Shorted low
      Check soon

      Causes

      • Starter relay driver wire shorted to ground in the engine harness
      • Relay coil shorted
      • Relay base corroded

      Checks

      1. 1Turn the key to start and listen for the relay click
      2. 2Pull the relay and measure its coil resistance
      3. 3Check the driver wire at the relay base for a short to ground
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

    • Cummins 2556Intake air heater circuit shorted low or driver voltage low

      The ECM drives the intake air heater circuit but sees its output pulled to ground.· Shorted low
      Check soon

      Causes

      • Intake heater driver wire shorted to ground
      • Heater relay coil shorted
      • Wire chafed at the manifold

      Checks

      1. 1Turn the key on in cold conditions and listen for the intake heater relay to click on
      2. 2Pull the heater relay and test its coil resistance for a short against the service value
      3. 3Measure the driver wire to ground at the harness
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

Shared checks

Checks, in order

  1. 1Measure the heater element resistance with the power disconnected and compare it with the service manual
  2. 2Measure the solenoid coil resistance and compare with the manual
  3. 3Check the lamp bulb or LED in the cluster and its wiring
  4. 4Check the starter relay, fuse and wiring for continuity and shorts to ground
  5. 5Check the heater relay and fuse feeding the heater, and test the relay by swapping it
  6. 6Check the harness for chafing, shorts and corrosion
  7. 7Look at the data link for missing lamp messages

Causes

  • Open heater element or relay
  • Open or shorted solenoid coil
  • Lamp or its wiring failed
  • Open or shorted starter relay circuit

Most common here: shorted high (4 of 17)

Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

When to stop

You'll notice: Harder cold starts with white smoke and rough running until warm.

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.