Cummins · Engine speed sensors
Cummins Crankshaft and camshaft speed and position sensors fault codes
The crankshaft position sensor reads a toothed wheel on the crankshaft so the ECM knows engine speed, and the camshaft position sensor reads a wheel on the camshaft so the ECM knows which stroke each cylinder is on. Together they time the injectors.
More about these partsLess
These codes also cover overspeed and low idle speed conditions.
Where to read it
Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.
What do these codes mean?
Cummins codes 115 to 7234 are all about the crankshaft and camshaft speed and position sensors. The most common failure type is real condition (5 of 14); 3 need an immediate stop. Start with this check: read engine speed while cranking: both sensors should give a signal, and a missing one points to that sensor or its wiring.
How urgent are they?
3 of 14 codes here mean stop now; 9 can wait until the shift ends, but find the cause before the next one; 2 are information only.
- Stop now3
- Check soon9
- Info2
What should I check first?
Read engine speed while cranking: both sensors should give a signal, and a missing one points to that sensor or its wiring
Shared checks14 of 14
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Engine speed/position1 code
Cummins 115Engine speed/position: Both sensor signals lost
The ECM has lost both the crankshaft and the camshaft speed signals, so it no longer knows where the engine is in its cycle.· OtherOtherStop nowCauses
- Crankshaft position sensor failed or its tone wheel is damaged
- Camshaft position sensor failed or its tone wheel is damaged
- Harness damaged or chafed between both sensors and the ECM
- Connector near the gear housing or flywheel housing contaminated with oil or water
Checks
- 1Check whether it cranks and whether the tachometer reads engine speed during cranking
- 2Inspect both sensor connectors and the harness for oil, water and damage
- 3Measure sensor resistance against the service data for your engine
- 4Check the sensor air gap and the tone wheel for damage or missing teeth
- 5Check the ECM supply voltage; a low battery can drop both signals
- 6Replace the failed sensor and clear the faults
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Engine crankshaft speed/position3 codes
Cummins 689Engine crankshaft speed/position: Erratic reading
The ECM's crankshaft speed signal is erratic or intermittent. The engine may still start with the camshaft signal, but running can be rough.· Lost messageLost messageCheck soonCauses
- Crankshaft position sensor loose or failing
- Tone wheel on the crankshaft or flywheel with missing or damaged teeth
- Connector or wires near the flywheel housing damaged
Checks
- 1Check the live engine speed in INSITE during cranking
- 2Remove the sensor and look for debris and damage on the tip
- 3Inspect the tone wheel through the sensor hole
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Source wording:Engine crankshaft speed/position - data erratic
Cummins 2321Engine crankshaft speed/position: Erratic reading
The ECM judges the engine crankshaft speed/position to be erratic, intermittent or implausible. The value jumps, drifts or disagrees with a related reading, which suggests a poor connection or a failing sensor.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Intermittent connector or wiring contact
- Sensor ageing or failing
- A real fluctuation in the system it measures
Checks
- 1Watch the engine crankshaft speed/position live and wiggle the harness and connector to catch dropouts
- 2Compare it with a related sensor to see which one is wrong
- 3Check the connector for moisture and corrosion
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:Engine crankshaft speed/position - data erratic or incorrect
Cummins 2468Engine crankshaft speed/position: Above normal· moderately severe
The engine crankshaft speed/position is above its normal operating range and the ECM rates it as moderately severe. The signal itself is valid, so this reflects a real operating condition or a sensor reading that no longer matches reality.· Real conditionReal conditionCheck soonCauses
- The monitored condition really is too high because of the system it measures
- A related fault that set first and is pushing the reading out of range
Checks
- 1Compare the live engine crankshaft speed/position with a second reading or gauge to see whether the condition is real
- 2Read the freeze-frame for speed, load and temperature when the code set
- 3Clear any other active codes first and retest under load
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Engine crankshaft speed/position - above normal - moderately severe
Engine camshaft speed/position sensor2 codes
Cummins 753Engine camshaft speed/position sensor: Abnormal rate of change
The engine camshaft speed/position sensor reading is changing faster than the real quantity could move. This is typical of a loose connector, an intermittent wire or a sensor that is starting to fail.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing intermittent contact
- Intermittent wiring fault that opens and closes
- Sensor starting to fail
Checks
- 1Watch the engine camshaft speed/position sensor reading live and wiggle the harness and connector to see whether it jumps
- 2Inspect the connector pins for corrosion and spread terminals
- 3Compare with a related sensor to see whether the jump is real
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Cummins 2322Engine camshaft speed/position sensor: Erratic reading
The ECM judges the engine camshaft speed/position sensor to be erratic, intermittent or implausible. The value jumps, drifts or disagrees with a related reading, which suggests a poor connection or a failing sensor.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Intermittent connector or wiring contact
- Sensor ageing or failing
- A real fluctuation in the system it measures
Checks
- 1Watch the engine camshaft speed/position sensor live and wiggle the harness and connector to catch dropouts
- 2Compare it with a related sensor to see which one is wrong
- 3Check the connector for moisture and corrosion
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:Engine camshaft speed/position sensor - data erratic or incorrect
Camshaft speed/position sensor1 code
Cummins 778Camshaft speed/position sensor: Erratic reading
The camshaft position signal is erratic. The ECM can still use the crankshaft signal, but starting may be longer and the engine may stumble.· Lost messageLost messageCheck soonCauses
- Camshaft sensor loose or damaged
- Camshaft tone wheel damaged or contaminated
- Connector or harness near the gear housing damaged
Checks
- 1Check the live engine speed and cam signal in INSITE while cranking
- 2Inspect the sensor and connector for oil and damage
- 3Check that the cam sensor is fully seated, its bolt is tight and its air gap to the tone wheel is correct
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Source wording:Camshaft speed/position sensor - data erratic
Engine speed2 codes
Cummins 2199Engine speed: Abnormal rate of change
The engine speed reading is changing faster than the real quantity could move. This is typical of a loose connector, an intermittent wire or a sensor that is starting to fail.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing intermittent contact
- Intermittent wiring fault that opens and closes
- Sensor starting to fail
Checks
- 1Watch the engine speed reading live and wiggle the harness and connector to see whether it jumps
- 2Inspect the connector pins for corrosion and spread terminals
- 3Compare with a related sensor to see whether the jump is real
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Cummins 6595Engine speed: Root cause not known
The ECM detects a problem with the engine speed but cannot tie it to one specific cause. It is a catch-all result, so the surrounding codes and the freeze-frame matter more than this one alone.· OtherOtherInfoCauses
- A related fault that set first
- An intermittent connection or supply problem
Checks
- 1Read all active and inactive codes and work the others first
- 2Check the supply, ground and connectors of the circuit involved
- 3Read the freeze-frame data for the conditions when it set
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Engine speed at idle3 codes
Cummins 3715Engine speed at idle: Below normal· moderately severe
The engine speed at idle is below its normal operating range and the ECM rates it as moderately severe. The signal itself is valid, so this reflects a real operating condition or a sensor reading that no longer matches reality.· Real conditionReal conditionCheck soonCauses
- The monitored condition really is too low because of the system it measures
- A related fault that set first and is pushing the reading out of range
Checks
- 1Compare the live engine speed at idle with a second reading or gauge to see whether the condition is real
- 2Read the freeze-frame for speed, load and temperature when the code set
- 3Clear any other active codes first and retest under load
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Engine speed at idle - below normal - moderately severe
Cummins 3716Engine speed at idle: Below normal· moderately severe
The engine speed at idle is below its normal operating range and the ECM rates it as moderately severe. The signal itself is valid, so this reflects a real operating condition or a sensor reading that no longer matches reality.· Real conditionReal conditionCheck soonCauses
- The monitored condition really is too low because of the system it measures
- A related fault that set first and is pushing the reading out of range
Checks
- 1Compare the live engine speed at idle with a second reading or gauge to see whether the condition is real
- 2Read the freeze-frame for speed, load and temperature when the code set
- 3Clear any other active codes first and retest under load
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Engine speed at idle - below normal - moderately severe
Cummins 7234Engine speed at idle: Below normal· least severe
The engine speed at idle is below its normal operating range and the ECM rates it as least severe. The signal itself is valid, so this reflects a real operating condition or a sensor reading that no longer matches reality.· Real conditionReal conditionInfoCauses
- The monitored condition really is too low because of the system it measures
- A related fault that set first and is pushing the reading out of range
Checks
- 1Compare the live engine speed at idle with a second reading or gauge to see whether the condition is real
- 2Read the freeze-frame for speed, load and temperature when the code set
- 3Clear any other active codes first and retest under load
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Engine speed at idle - below normal - least severe
Other codes2 codes
Cummins 234Engine speed too high (overspeed)
The ECM measured engine speed above the allowed limit. Cummins engines will cut fuel to protect the engine when this happens.· Real conditionReal conditionStop nowCauses
- Driver or machine over-revving the engine, for example a missed or wrong downshift
- Runaway caused by oil or fuel being drawn into the intake
- Faulty speed signal making the ECM think the engine is faster than it is
Checks
- 1Read the freeze-frame data and see the engine speed when the code set
- 2Ask about the event: downshift, descent or a loss of load
- 3Check the turbo for oil leakage into the intake and the crankcase breather for oil
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Cummins 731Camshaft and crankshaft position out of alignment
The ECM sees the camshaft signal and the crankshaft signal out of the expected relationship. That means the timing has moved, a sensor is mounted wrongly, or a wheel is damaged.· OtherOtherStop nowCauses
- Timing gear or wheel moved or damaged
- Camshaft or crankshaft sensor loose or wrongly fitted after a repair
- Gear train backlash or damage
Checks
- 1Check whether it started after recent engine work or injector or gear train service
- 2Check both sensors are fully seated and bolted down
- 3Check the tone wheels on the crankshaft and camshaft for missing teeth or movement through the sensor holes
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Read engine speed while cranking: both sensors should give a signal, and a missing one points to that sensor or its wiring
- 2Inspect each sensor, its mounting and the tone wheel for damage, play and metal debris
- 3Check the connectors and harness for oil, corrosion and chafing, and wiggle them during cranking
- 4Check the sensor reference, return and signal at the connector for the correct voltage and continuity
- 5Confirm the mechanical timing and the wheel alignment if the codes appeared after an engine repair
- 6Compare against any engine overspeed or idle-speed codes to see whether a real speed problem exists
Causes
- Damaged or loose sensor, wrong air gap or contaminated tip
- Damaged or dirty tone wheel or a loose timing gear
- Harness damaged or connector corroded, or interference from a nearby high-current wire
- Failed sensor
Most common here: real condition (5 of 14)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: Hard or no start, rough running, loss of power or a sudden stall; if one sensor is lost the engine may keep running on the other with reduced performance.
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Cummins ISX15 (2013-2018) Fault Codes List (Diesel Repair)
- Cummins L9 (2024-2025) Fault Code List (Diesel Repair)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
