Cummins · Engine speed sensors - SPN 612 FMI 2
Cummins Fault Code 115
Engine speed/position - both sensor signals lost
What does Cummins code 115 mean?
The ECM has lost both the crankshaft and the camshaft speed signals, so it no longer knows where the engine is in its cycle. Urgency: stop now - shut down and fix before working on. Check first: check whether it cranks and whether the tachometer reads engine speed during cranking.
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Check whether it cranks and whether the tachometer reads engine speed during cranking
Then 5 more checksWhere to read it
Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.
Checks
0 of 6 done
Causes
- Crankshaft position sensor failed or its tone wheel is damaged
- Camshaft position sensor failed or its tone wheel is damaged
- Harness damaged or chafed between both sensors and the ECM
- Connector near the gear housing or flywheel housing contaminated with oil or water
How it failed
You'll notice: The engine cranks but does not start, or it shuts down while running.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Crankshaft and camshaft speed and position sensors
- 115Engine speed/position - both sensor signals lostOtherStop now
- 234Engine speed too high (overspeed)Real conditionStop now
- 689Engine crankshaft speed/position - data erraticLost messageCheck soon
- 731Camshaft and crankshaft position out of alignmentOtherStop now
- 753Engine camshaft speed/position sensor - abnormal rate of changeErratic or implausibleCheck soon
- 778Camshaft speed/position sensor - data erraticLost messageCheck soon
- 2199Engine speed - abnormal rate of changeErratic or implausibleCheck soon
- 2321Engine crankshaft speed/position - data erratic or incorrectErratic or implausibleCheck soon
- 2322Engine camshaft speed/position sensor - data erratic or incorrectErratic or implausibleCheck soon
Show the other 5 codesHide the other codes
- 2468Engine crankshaft speed/position - above normal - moderately severeReal conditionCheck soon
- 3715Engine speed at idle - below normal - moderately severeReal conditionCheck soon
- 3716Engine speed at idle - below normal - moderately severeReal conditionCheck soon
- 6595Engine speed - root cause not knownOtherInformation
- 7234Engine speed at idle - below normal - least severeReal conditionInformation
Related on Equipments Finder
Source
Cummins ISX15 (2013-2018) Fault Codes List (Diesel Repair)
This source lists 115 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15/X15/ISB6.7/B6.7 engines (J1939 SPN 612, FMI 2); same code list used in trucks, buses and machines with these engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
