Cat · Fuel system
Cat Fault Code CID 1797 FMI 04
Fuel rail pressure sensor voltage low
What does Cat code CID 1797 FMI 04 mean?
The fuel rail pressure signal sat below 0.2 V for 0.6 seconds. The manual lists a harness shorted to ground, a shorted sensor, or the ECM. Urgency: stop now - shut down and fix before working on. Check first: start the engine with Cat ET connected and see whether 1797-4 is active.
- CID 1797
- Which component is at fault
- FMI 04
- Voltage below normal or shorted low
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Start the engine with Cat ET connected and see whether 1797-4 is active.
Then 4 more checksWhere this code shows
Turn the key on and check the cluster or monitor for a warning lamp.
Checks
0 of 5 done
Causes
- Harness signal wire shorted to ground
- Shorted fuel rail pressure sensor
- Engine ECM
How it failed
You'll notice: Hard starting, stalling or no-start, and the ECM may limit fuel because it thinks rail pressure is zero.
Shorted lowRead from FMI 4: voltage below normal or shorted low
The signal sits at or near zero volts - less than a working sensor can send.
- Meter test
- Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
- Good result
- Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
When to stop
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Fuel rail pressure and injectors
3 other codes on this part are also shorted low (CID 1 FMI 06, CID 4 FMI 06, CID 6 FMI 06). When they show together, start at the wiring and connector they share.
- CID 6 FMI 02Fuel injector 6 data incorrectErratic or implausibleCheck soon
- CID 6 FMI 05Fuel injector 6 current lowOpen circuitCheck soon
- CID 6 FMI 06Fuel injector 6 current highShorted lowCheck soon
- E396High fuel rail pressureOtherStop now
- E398Low fuel rail pressureOtherStop now
- CID 526 FMI 05Wastegate solenoid current lowOpen circuitCheck soon
- CID 1779 FMI 05Fuel rail pressure valve solenoid current lowOpen circuitStop now
- CID 1797 FMI 03Fuel rail pressure sensor voltage highShorted highStop now
- CID 1797 FMI 04Fuel rail pressure sensor voltage lowShorted lowStop now
Show the other 10 codesHide the other codes
- CID 1 FMI 02Fuel injector 1 data incorrectErratic or implausibleCheck soon
- CID 1 FMI 05Fuel injector 1 current lowOpen circuitCheck soon
- CID 1 FMI 06Fuel injector 1 current highShorted lowCheck soon
- CID 1 FMI 07Fuel injector 1 mechanical system not respondingPart or controllerCheck soon
- CID 2 FMI 02Fuel injector 2 data incorrectErratic or implausibleCheck soon
- CID 2 FMI 05Fuel injector 2 current lowOpen circuitCheck soon
- CID 3 FMI 02Fuel injector 3 data incorrectErratic or implausibleCheck soon
- CID 3 FMI 05Fuel injector 3 current lowOpen circuitCheck soon
- CID 4 FMI 05Fuel injector 4 current lowOpen circuitCheck soon
- CID 4 FMI 06Fuel injector 4 current highShorted lowCheck soon
Related on Equipments Finder
Source
This source lists CID 1797 FMI 04 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Cat 924H wheel loader with C6.6 engine (engine ECM), per the 924H field maintenance manual; the same CID-FMI scheme is used on other Cat machines with C-series ECMs.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
