EF Logo

Bobcat · Drive

Bobcat Drive+ steering pressure, wheel angle sensors and steer valves fault codes

Drive+ machines steer the wheels with a hydraulic steering circuit that has a wheel angle sensor and a steer valve at each wheel, left and right, front and rear, plus a system pressure and calibration check. A code names the wheel and the part and how the circuit failed.

FaultCheckD7506Bobcat · Drive+ steering pressure, wheel angle sensors and steer valves
Code shows hereFAULTD7506

Where this code shows

On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.

What do these codes mean?

Bobcat codes D7506 to D7584 are all about the drive+ steering pressure, wheel angle sensors and steer valves. The most common failure type is shorted high (10 of 32); none needs an immediate stop. Start with this check: steer lock to lock and watch the four wheel angle values on the service screen; the wheel that is off or frozen is the one to test.

How urgent are they?

None of the 32 codes here means stop now; all 32 can wait until the shift ends, but find the cause before the next one.

  • Check soon32

What should I check first?

Steer lock to lock and watch the four wheel angle values on the service screen; the wheel that is off or frozen is the one to test.

Shared checks

32 of 32

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Bobcat D7506Drive+ steering valve cartridge stuck

    The controller sees no movement on the steering valve cartridge signal while the machine moves, so the reading is judged stuck and that wheel does not steer in that direction.· Other
    Check soon

    Causes

    • Sensor linkage loose or broken
    • Sensor failed with a frozen output
    • Connector or wiring fault holding the signal fixed

    Checks

    1. 1Move the machine and watch the steering valve cartridge reading; a value that never changes confirms the stuck signal.
    2. 2Check the sensor linkage and mounting for a loose or broken part.
    3. 3Check the connector at the steer valve connector and measure the signal voltage while moving.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7513Drive+ right front wheel angle sensor stuck

    The controller sees no movement on the wheel angle sensor signal while the machine moves, so the reading is judged stuck and that wheel angle is not known to the controller, so steering is limited.· Other
    Check soon

    Causes

    • Sensor linkage loose or broken
    • Sensor failed with a frozen output
    • Connector or wiring fault holding the signal fixed

    Checks

    1. 1Move the machine and watch the wheel angle sensor reading; a value that never changes confirms the stuck signal.
    2. 2Check the sensor linkage and mounting for a loose or broken part.
    3. 3Check the connector at the wheel angle sensor plug at the hub and measure the signal voltage while moving.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7514Drive+ left front wheel angle sensor stuck

    Drive+ left front wheel angle sensor stuck: same fault as D7513 (the signal does not change when it should), here on the left front wheel angle sensor.· Other
    Check soon

    Causes

    • Sensor linkage loose or broken
    • Sensor failed with a frozen output

    Checks

    1. 1Move the machine and watch whether the left front wheel angle sensor value changes.
    2. 2Test steps: see D7513.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7515Drive+ right rear wheel angle sensor stuck

    Drive+ right rear wheel angle sensor stuck: same fault as D7513 (the signal does not change when it should), here on the right rear wheel angle sensor.· Other
    Check soon

    Causes

    • Sensor linkage loose or broken
    • Sensor failed with a frozen output

    Checks

    1. 1Move the machine and watch whether the right rear wheel angle sensor value changes.
    2. 2Test steps: see D7513.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7516Drive+ left rear wheel angle sensor stuck

    Drive+ left rear wheel angle sensor stuck: same fault as D7513 (the signal does not change when it should), here on the left rear wheel angle sensor.· Other
    Check soon

    Causes

    • Sensor linkage loose or broken
    • Sensor failed with a frozen output

    Checks

    1. 1Move the machine and watch whether the left rear wheel angle sensor value changes.
    2. 2Test steps: see D7513.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7523Drive+ right front wheel angle sensor out of range high

    The controller reads the wheel angle sensor wheel angle signal above its normal range, which is usually a wire shorted to supply or a sensor that has failed high, so that wheel angle is not known to the controller, so steering is limited.· Shorted high
    Check soon

    Causes

    • Signal wire shorted to the 5 V or battery supply
    • Sensor failed with its output pinned high
    • Ground wire open so the signal floats high
    • Water in the connector bridging signal to supply

    Checks

    1. 1Unplug the wheel angle sensor and measure the signal wire with the key on; a high voltage with the sensor removed means a short in the harness.
    2. 2Check the sensor ground at the plug; an open ground drives the signal high.
    3. 3Measure the 5 V reference at the wheel angle sensor plug to confirm it is not above 5 V.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat D7524Drive+ left front wheel angle sensor out of rane high

    Drive+ left front wheel angle sensor out of rane high: same fault as D7523 (the signal is above its normal range), here on the left front wheel angle sensor out of rane.· Other
    Check soon

    Causes

    • Signal wire shorted to the 5 V or battery supply
    • Sensor failed with its output pinned high

    Checks

    1. 1Unplug the left front wheel angle sensor out of rane and measure the signal wire for a short to supply.
    2. 2Test steps: see D7523.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7525Drive+ right rear wheel angle sensor out of range high

    Drive+ right rear wheel angle sensor out of range high: same fault as D7523 (the signal is above its normal range), here on the right rear wheel angle sensor.· Other
    Check soon

    Causes

    • Signal wire shorted to the 5 V or battery supply
    • Sensor failed with its output pinned high

    Checks

    1. 1Unplug the right rear wheel angle sensor and measure the signal wire for a short to supply.
    2. 2Test steps: see D7523.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7526Drive+ left rear wheel angle sensor out of range high

    Drive+ left rear wheel angle sensor out of range high: same fault as D7523 (the signal is above its normal range), here on the left rear wheel angle sensor.· Other
    Check soon

    Causes

    • Signal wire shorted to the 5 V or battery supply
    • Sensor failed with its output pinned high

    Checks

    1. 1Unplug the left rear wheel angle sensor and measure the signal wire for a short to supply.
    2. 2Test steps: see D7523.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7533Drive+ right front wheel angle sensor out of range low

    The controller reads the wheel angle sensor wheel angle signal below its normal range, typically a wire shorted to ground, an open supply or a sensor failed low, so that wheel angle is not known to the controller, so steering is limited.· Shorted low
    Check soon

    Causes

    • Signal wire shorted to ground
    • Supply wire to the sensor open or the sensor not powered
    • Sensor failed with its output pinned low
    • Pin backed out of the connector

    Checks

    1. 1Measure the 5 V reference at the wheel angle sensor plug; no reference means the fault is in the supply wire, not the sensor.
    2. 2Unplug the sensor and measure the signal wire to ground for a short.
    3. 3Check the connector at the wheel angle sensor plug at the hub for a backed-out pin.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat D7534Drive+ left front wheel angle sensor out of range low

    Drive+ left front wheel angle sensor out of range low: same fault as D7533 (the signal is below its normal range), here on the left front wheel angle sensor.· Other
    Check soon

    Causes

    • Signal wire shorted to ground
    • Supply wire to the sensor open or the sensor not powered

    Checks

    1. 1Measure the 5 V reference and the signal wire to ground at the left front wheel angle sensor plug.
    2. 2Test steps: see D7533.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7535Drive+ right rear wheel angle sensor out of range low

    Drive+ right rear wheel angle sensor out of range low: same fault as D7533 (the signal is below its normal range), here on the right rear wheel angle sensor.· Other
    Check soon

    Causes

    • Signal wire shorted to ground
    • Supply wire to the sensor open or the sensor not powered

    Checks

    1. 1Measure the 5 V reference and the signal wire to ground at the right rear wheel angle sensor plug.
    2. 2Test steps: see D7533.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7536Drive+ left rear wheel angle sensor out of range low

    Drive+ left rear wheel angle sensor out of range low: same fault as D7533 (the signal is below its normal range), here on the left rear wheel angle sensor.· Other
    Check soon

    Causes

    • Signal wire shorted to ground
    • Supply wire to the sensor open or the sensor not powered

    Checks

    1. 1Measure the 5 V reference and the signal wire to ground at the left rear wheel angle sensor plug.
    2. 2Test steps: see D7533.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7547Drive+ right front steer extend short to battery

    The controller reads the steer extend valve circuit tied to battery voltage when it should only be switched by the controller.· Shorted high
    Check soon

    Causes

    • Output wire rubbed through at the steer valve connector and touching a live supply wire
    • Water or corrosion in the plug bridging a pin to a power pin
    • Controller output stage failed shorted to supply

    Checks

    1. 1Unplug the steer extend valve at the steer valve connector and check its output wire for voltage with the key on; any voltage with the load removed is a short to supply.
    2. 2Trace the wire back from the steer valve coil for chafing next to live supply wires and for melted insulation.
    3. 3Replace the steer valve coil only if the wire reads clean and the part itself reads shorted.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat D7548Drive+ left front steer extend short to battery

    Drive+ left front steer extend short to battery: same fault as D7547 (the circuit reads tied to battery voltage), here on the left front steer extend.· Shorted high
    Check soon

    Causes

    • Output wire rubbed through
    • Water or corrosion in the plug bridging a pin to a power pin

    Checks

    1. 1Unplug the left front steer extend and look for voltage on its output wire with the key on.
    2. 2Test steps: see D7547.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat D7549Drive+ right rear steer extend short to battery

    Drive+ right rear steer extend short to battery: same fault as D7547 (the circuit reads tied to battery voltage), here on the right rear steer extend.· Shorted high
    Check soon

    Causes

    • Output wire rubbed through
    • Water or corrosion in the plug bridging a pin to a power pin

    Checks

    1. 1Unplug the right rear steer extend and look for voltage on its output wire with the key on.
    2. 2Test steps: see D7547.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat D7550Drive+ left rear steer extend short to battery

    Drive+ left rear steer extend short to battery: same fault as D7547 (the circuit reads tied to battery voltage), here on the left rear steer extend.· Shorted high
    Check soon

    Causes

    • Output wire rubbed through
    • Water or corrosion in the plug bridging a pin to a power pin

    Checks

    1. 1Unplug the left rear steer extend and look for voltage on its output wire with the key on.
    2. 2Test steps: see D7547.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat D7551Drive+ steer pressure short to battery

    The controller reads the steer pressure circuit tied to battery voltage when it should only be switched by the controller.· Shorted high
    Check soon

    Causes

    • Output wire rubbed through at the steer valve connector and touching a live supply wire
    • Water or corrosion in the plug bridging a pin to a power pin
    • Controller output stage failed shorted to supply

    Checks

    1. 1Unplug the steer pressure at the steer valve connector and check its output wire for voltage with the key on; any voltage with the load removed is a short to supply.
    2. 2Trace the wire back from the steer valve coil for chafing next to live supply wires and for melted insulation.
    3. 3Replace the steer valve coil only if the wire reads clean and the part itself reads shorted.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat D7557Drive+ right front steer extend short to ground

    The controller reads the steer extend valve circuit pulled to ground, so it cannot drive the load.· Shorted low
    Check soon

    Causes

    • Wire chafed against the frame or a bracket at the steer valve connector
    • The steer valve coil shorted to its housing
    • Water in the connector or a pin touching the shell

    Checks

    1. 1With the plug off, test the steer extend valve output wire to chassis ground; a reading near zero shows a harness short.
    2. 2Measure from each pin of the steer valve coil to its body; any continuity means the part itself is shorted.
    3. 3Look for harness sections crushed under clamps or cut by sharp edges at the steer valve connector.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat D7558Drive+ right front steer retract short to ground

    The controller reads the steer retract valve circuit pulled to ground, so it cannot drive the load.· Shorted low
    Check soon

    Causes

    • Wire chafed against the frame or a bracket at the steer valve connector
    • The steer valve coil shorted to its housing
    • Water in the connector or a pin touching the shell

    Checks

    1. 1With the plug off, test the steer retract valve output wire to chassis ground; a reading near zero shows a harness short.
    2. 2Measure from each pin of the steer valve coil to its body; any continuity means the part itself is shorted.
    3. 3Look for harness sections crushed under clamps or cut by sharp edges at the steer valve connector.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat D7559Drive+ left front steer extend short to ground

    Drive+ left front steer extend short to ground: same fault as D7557 (the circuit reads pulled to ground), here on the left front steer extend.· Shorted low
    Check soon

    Causes

    • Wire chafed against the frame or a bracket
    • The steer valve coil shorted to its housing

    Checks

    1. 1Test the left front steer extend output wire to chassis ground with the plug off.
    2. 2Test steps: see D7557.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat D7560Drive+ left front steer retract short to ground

    Drive+ left front steer retract short to ground: same fault as D7558 (the circuit reads pulled to ground), here on the left front steer retract.· Shorted low
    Check soon

    Causes

    • Wire chafed against the frame or a bracket
    • The steer valve coil shorted to its housing

    Checks

    1. 1Test the left front steer retract output wire to chassis ground with the plug off.
    2. 2Test steps: see D7558.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat D7561Drive+ right rear steer extend short to ground

    Drive+ right rear steer extend short to ground: same fault as D7557 (the circuit reads pulled to ground), here on the right rear steer extend.· Shorted low
    Check soon

    Causes

    • Wire chafed against the frame or a bracket
    • The steer valve coil shorted to its housing

    Checks

    1. 1Test the right rear steer extend output wire to chassis ground with the plug off.
    2. 2Test steps: see D7557.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat D7562Drive+ right rear steer retract short to ground

    Drive+ right rear steer retract short to ground: same fault as D7558 (the circuit reads pulled to ground), here on the right rear steer retract.· Shorted low
    Check soon

    Causes

    • Wire chafed against the frame or a bracket
    • The steer valve coil shorted to its housing

    Checks

    1. 1Test the right rear steer retract output wire to chassis ground with the plug off.
    2. 2Test steps: see D7558.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat D7563Drive+ left rear steer extend short to ground

    Drive+ left rear steer extend short to ground: same fault as D7557 (the circuit reads pulled to ground), here on the left rear steer extend.· Shorted low
    Check soon

    Causes

    • Wire chafed against the frame or a bracket
    • The steer valve coil shorted to its housing

    Checks

    1. 1Test the left rear steer extend output wire to chassis ground with the plug off.
    2. 2Test steps: see D7557.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat D7564Drive+ left rear steer retract short to ground

    Drive+ left rear steer retract short to ground: same fault as D7558 (the circuit reads pulled to ground), here on the left rear steer retract.· Shorted low
    Check soon

    Causes

    • Wire chafed against the frame or a bracket
    • The steer valve coil shorted to its housing

    Checks

    1. 1Test the left rear steer retract output wire to chassis ground with the plug off.
    2. 2Test steps: see D7558.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat D7565Drive+ steer pressure short to ground

    The controller reads the steer pressure circuit pulled to ground, so it cannot drive the load.· Shorted low
    Check soon

    Causes

    • Wire chafed against the frame or a bracket at the steer valve connector
    • The steer valve coil shorted to its housing
    • Water in the connector or a pin touching the shell

    Checks

    1. 1With the plug off, test the steer pressure output wire to chassis ground; a reading near zero shows a harness short.
    2. 2Measure from each pin of the steer valve coil to its body; any continuity means the part itself is shorted.
    3. 3Look for harness sections crushed under clamps or cut by sharp edges at the steer valve connector.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat D7568Drive+ angle sensors not calibrated

    The wheel angle sensor needs a calibration before it can run normally, so that wheel angle is not known to the controller, so steering is limited.· Lost message
    Check soon

    Causes

    • Controller or sensor replaced
    • Calibration lost after a reset or reprogramming

    Checks

    1. 1Run the wheel angle sensor calibration from the service menu.
    2. 2Check the machine is warm and on level ground as the procedure requires.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Bobcat D7581Drive+ right front steer retract short to battery

    The controller reads the steer retract valve circuit tied to battery voltage when it should only be switched by the controller.· Shorted high
    Check soon

    Causes

    • Output wire rubbed through at the steer valve connector and touching a live supply wire
    • Water or corrosion in the plug bridging a pin to a power pin
    • Controller output stage failed shorted to supply

    Checks

    1. 1Unplug the steer retract valve at the steer valve connector and check its output wire for voltage with the key on; any voltage with the load removed is a short to supply.
    2. 2Trace the wire back from the steer valve coil for chafing next to live supply wires and for melted insulation.
    3. 3Replace the steer valve coil only if the wire reads clean and the part itself reads shorted.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat D7582Drive+ left front steer retract short to battery

    Drive+ left front steer retract short to battery: same fault as D7581 (the circuit reads tied to battery voltage), here on the left front steer retract.· Shorted high
    Check soon

    Causes

    • Output wire rubbed through
    • Water or corrosion in the plug bridging a pin to a power pin

    Checks

    1. 1Unplug the left front steer retract and look for voltage on its output wire with the key on.
    2. 2Test steps: see D7581.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat D7583Drive+ right rear steer retract short to battery

    Drive+ right rear steer retract short to battery: same fault as D7581 (the circuit reads tied to battery voltage), here on the right rear steer retract.· Shorted high
    Check soon

    Causes

    • Output wire rubbed through
    • Water or corrosion in the plug bridging a pin to a power pin

    Checks

    1. 1Unplug the right rear steer retract and look for voltage on its output wire with the key on.
    2. 2Test steps: see D7581.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat D7584Drive+ left rear steer retract short to battery

    Drive+ left rear steer retract short to battery: same fault as D7581 (the circuit reads tied to battery voltage), here on the left rear steer retract.· Shorted high
    Check soon

    Causes

    • Output wire rubbed through
    • Water or corrosion in the plug bridging a pin to a power pin

    Checks

    1. 1Unplug the left rear steer retract and look for voltage on its output wire with the key on.
    2. 2Test steps: see D7581.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

Shared checks

Checks, in order

  1. 1Steer lock to lock and watch the four wheel angle values on the service screen; the wheel that is off or frozen is the one to test.
  2. 2Measure the coil resistance of the named steer valve with the plug off and compare it with the other three wheels.
  3. 3Check the angle sensor mounting and connector at the named wheel.
  4. 4Run the Drive+ steering calibration after replacing a sensor or valve.
  5. 5Look at the harness at the wheel pivots for chafing, which breaks wires only when the wheel turns.

Causes

  • Wheel angle sensor failed, loose on its linkage or out of calibration
  • Steer valve coil open, shorted or sticking
  • Harness chafed at the wheel hub or steering pivot
  • Low steering pressure from an oil or pump problem

Most common here: shorted high (10 of 32)

Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

When to stop

You'll notice: Steering is weak, slow or off-centre on one wheel, or the machine will not steer straight, and a steering code shows.

Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.