EF Logo

Truck and excavator matching calculator: how many trucks per excavator

Match a fleet to its loader. Enter the bucket, the excavator’s cycle, the truck and the haul, and see how many trucks keep the excavator working without queues.

The formula

Trucks = truck cycle time ÷ load time. Passes = truck load ÷ (bucket × fill factor).

What it works out

Match the number of trucks to an excavator or loader from passes, load time and haul cycle.

Why it matters

Too few trucks leave the excavator waiting; too many queue at the face.

How to use it

  1. Enter the Bucket Capacity, the Bucket Fill Factor and the Excavator Cycle Time in seconds.
  2. Enter the Truck Body Volume, the Truck Payload and the Loose Density of the material. The load is the smaller of the body volume and the payload.
  3. Enter the One-way Haul Distance and the Loaded and Empty speeds.
  4. Enter the Dump and Turn Time, the time to Spot at the Loader, and the Job Efficiency.
  5. Read Trucks Needed, the passes to fill a truck, the load time, the truck cycle and the Fleet Output.

Quick reference

Printable chart

Trucks needed by haul distance (1.2 m³ bucket, 16 m³ tipper)

Haul (km, one way)Truck cycle (min)Trucks neededOutput (m³/h)
111.43 min2 trucks126.9 m³/hr
214.93 min3 trucks126.9 m³/hr
525.43 min5 trucks126.9 m³/hr
1042.93 min8 trucks126.9 m³/hr
1560.43 min11 trucks126.9 m³/hr
2077.93 min14 trucks126.9 m³/hr

A 1.2 m³ bucket with 22 s cycle, 16 m³ and 25 t tipper, 30 km/h loaded, 40 km/h empty.

The method

Passes per truck = the load that fits the truck ÷ (bucket × fill factor), rounded down so the truck is not overloaded. Load time = passes × excavator cycle + spot time. Truck cycle = load time + loaded haul + empty return + dump and turn. Trucks needed = truck cycle ÷ load time, rounded up. Fleet output is the loader’s rate, passes × bucket load per load time, times job efficiency.

Volume or weight decides the load

A truck is full when it reaches either its body volume or its legal payload, whichever comes first. Light material, such as dry sand or topsoil, fills the body first. Heavy material, like wet clay or rock, reaches the payload first, so the tool takes the smaller of the two. Use the loose density, not the density in the ground, because the bucket carries loose material.

A good match

Three to six passes per truck is a good match: fewer passes mean the bucket is too big for the truck and loading is hard on the tyres, more mean the loader is slow and the trucks wait. One truck too few leaves the excavator idle, one too many just makes a queue at the face. The result gives a whole number of trucks, so check the half-truck case: if the exact figure is, say, 4.1, the fifth truck is hardly used and a slightly larger bucket or truck may suit better. On a long haul, add a truck for breakdowns and refuelling.

Worked examples

  • A 1.2 m³ bucket loads a 16 m³ tipper in 14 passes and 5.93 min. With a 5 km haul the truck cycle is 25.43 min, so you need 4.29 trucks, which rounds to 5 trucks, for an output of 126.9 m³/hr.
  • Lengthening the haul to 15 km gives a 53.65 min cycle and needs 10 trucks, but the output stays at 126.9 m³/hr: the excavator is the limit, not the trucks.
  • A 2.4 m³ bucket on dense material (1.9 t/m³) loads 28.73 t in 7 passes for a 3 km haul, which needs 5 trucks and gives 209.2 m³/hr.

Frequently asked questions

How many trucks do I need per excavator?

Divide the truck’s full cycle time (load, haul, dump, return) by the time the excavator takes to load one truck, and round up.

How many bucket passes should fill a truck?

Three to six is a good match. Fewer means the bucket is too large, more means loading is slow.

What if the number is not a whole number?

Always round up. The result shows the exact figure too, so you can see how close the last truck is to being needed.

Why does the truck payload matter?

Heavy material reaches the payload limit before the body is full. The load is the smaller of the two.

Does this work for a wheel loader?

Yes. Enter the loader’s bucket, its cycle time and the same truck details.

Add this calculator to your website

Copy the code and paste it into your page. The calculator is free and works as it does here.

<iframe src="https://www.equipmentsfinder.com/embed/field-tools/truck-excavator-matching-calculator" title="Truck and excavator matching calculator: how many trucks per excavator" width="100%" height="620" style="border:0;max-width:720px" loading="lazy"></iframe>
<p style="font-size:12px"><a href="https://www.equipmentsfinder.com/field-tools/truck-excavator-matching-calculator">Truck and excavator matching calculator: how many trucks per excavator</a> by <a href="https://www.equipmentsfinder.com">EquipmentsFinder</a></p>
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.