Detroit · Engine sensors and levels
Detroit Engine oil pressure sensor and low oil pressure fault codes
The MCM reads the engine oil pressure sensor in the oil gallery and compares the value with what it expects for the engine speed and oil temperature. Detroit uses SPN 100 for the real low-pressure warnings and the derate, and for sensor, plausibility and parameter faults.
Where to read it
Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.
What do these codes mean?
Detroit codes SPN 100 FMI 0 to SPN 521136 FMI 5 are all about the engine oil pressure sensor and low oil pressure. The most common failure type is real condition (9 of 23); 3 need an immediate stop. Start with this check: check the oil level and condition on the dipstick before anything electrical, and look for fuel or coolant in the oil.
How urgent are they?
3 of 23 codes here mean stop now; the other 20 can wait until the shift ends, but find the cause before the next one.
- Stop now3
- Check soon20
What should I check first?
Check the oil level and condition on the dipstick before anything electrical, and look for fuel or coolant in the oil.
Shared checks23 of 23
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Detroit SPN 100 FMI 0Oil Pressure Stuck
Detroit lists SPN 100 FMI 0 as "Oil Pressure Stuck". The MCM reports that the measured value itself is out of its normal range; the engine oil pressure sensor may be correct and a real condition may exist. The oil pressure sensor screws into the main oil gallery; the controller compares its reading with a model of expected pressure at the present speed and oil temperature.· Real conditionReal conditionStop nowCauses
- A real fault in the system the engine oil pressure sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the engine oil pressure sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 100 FMI 1Low Engine Oil Pressure
The MCM measured the engine oil pressure below the minimum it allows for the current engine speed. Detroit treats this as a real protection fault, so the engine may be derated or shut down after a warning.· Real conditionReal conditionStop nowCauses
- Oil level too low, or oil thinned by fuel or coolant
- Worn oil pump, worn main or rod bearings, or a stuck open relief valve
- Blocked oil filter or a cooler passage restricted
- Oil pressure sensor reading wrongly because of corrosion or wiring damage
Checks
- 1Stop the engine and check the oil level and condition on the dipstick; look for a fuel smell and milky oil.
- 2Fit a mechanical gauge at the oil gallery port and compare it with the live value in the diagnostic tool at idle and at high idle.
- 3If the gauge shows good pressure but the tool does not, inspect the oil pressure sensor connector and wiring for oil and corrosion.
- 4Check the oil and filter service history and the oil grade used.
- 5If the gauge also reads low, stop running the engine and investigate the pump, bearings and relief valve.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 100 FMI 3Engine Oil Pressure Sensor Circuit Failed High
Detroit lists SPN 100 FMI 3 as "Engine Oil Pressure Sensor Circuit Failed High". The MCM saw the engine oil pressure sensor signal above its valid range. That usually means the signal wire is shorted to a supply voltage or is open at the sensor. The oil pressure sensor screws into the main oil gallery; the controller compares its reading with a model of expected pressure at the present speed and oil temperature.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to the 5 V supply or open between the engine oil pressure sensor and the MCM
- The engine oil pressure sensor has failed inside
Checks
- 1Unplug the engine oil pressure sensor and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
- 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 100 FMI 4Engine Oil Pressure Sensor Circuit Failed Low
Detroit lists SPN 100 FMI 4 as "Engine Oil Pressure Sensor Circuit Failed Low". The MCM saw the engine oil pressure sensor signal below its valid range. That usually means the signal wire is shorted to ground or the sensor has failed. The oil pressure sensor screws into the main oil gallery; the controller compares its reading with a model of expected pressure at the present speed and oil temperature.· Shorted lowShorted lowCheck soonCauses
- Signal wire chafed against the engine and shorted to ground
- The engine oil pressure sensor has failed inside or its supply wire is open
Checks
- 1Unplug the engine oil pressure sensor and check whether the signal rises; if it stays low the harness is shorted to ground.
- 2Check the sensor supply at the connector with the key on and trace it back to the MCM if it is missing.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 100 FMI 10Low Oil Pressure Derate
Detroit lists SPN 100 FMI 10 as "Low Oil Pressure Derate". The MCM judged the engine oil pressure sensor reading erratic or not plausible compared with other sensors or its own history. The oil pressure sensor screws into the main oil gallery; the controller compares its reading with a model of expected pressure at the present speed and oil temperature.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting engine oil pressure sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the engine oil pressure sensor reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 100 FMI 13Parameterization for OPC Is Incorrect
Detroit lists SPN 100 FMI 13 as "Parameterization for OPC Is Incorrect". The MCM found the engine oil pressure sensor value drifted away from what the engine state says it should be. The oil pressure sensor screws into the main oil gallery; the controller compares its reading with a model of expected pressure at the present speed and oil temperature.· Part or controllerPart or controllerCheck soonCauses
- Sensor aged, contaminated or out of calibration
- A real fault in the system being measured
Checks
- 1Compare the engine oil pressure sensor reading with a reference gauge or thermometer with the engine off and cold.
- 2Check the system around the engine oil pressure sensor for leaks, restrictions or contamination.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 100 FMI 14Engine Oil Pressure Sensor Plausibility Check Error
Detroit lists SPN 100 FMI 14 as "Engine Oil Pressure Sensor Plausibility Check Error". The MCM judged the engine oil pressure sensor reading erratic or not plausible compared with other sensors or its own history. The oil pressure sensor screws into the main oil gallery; the controller compares its reading with a model of expected pressure at the present speed and oil temperature.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting engine oil pressure sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the engine oil pressure sensor reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 100 FMI 15Engine Oil Pressure Rationality Error High
Same failure as SPN 100 FMI 14 ("Engine Oil Pressure Sensor Plausibility Check Error") on a sibling part: Detroit lists SPN 100 FMI 15 as "Engine Oil Pressure Rationality Error High". The oil pressure sensor screws into the main oil gallery; the controller compares its reading with a model of expected pressure at the present speed and oil temperature.· Real conditionReal conditionCheck soonCauses
- The causes listed under SPN 100 FMI 14, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 100 FMI 14, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 100 FMI 17Oil Pressure Very Low
Detroit lists SPN 100 FMI 17 as "Oil Pressure Very Low". The MCM reports that the measured value itself is out of its normal range; the engine oil pressure sensor may be correct and a real condition may exist. The oil pressure sensor screws into the main oil gallery; the controller compares its reading with a model of expected pressure at the present speed and oil temperature.· Real conditionReal conditionStop nowCauses
- A real fault in the system the engine oil pressure sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the engine oil pressure sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 100 FMI 20Oil Pressure too High
Detroit lists SPN 100 FMI 20 as "Oil Pressure too High". The MCM found the engine oil pressure sensor value drifted away from what the engine state says it should be. The oil pressure sensor screws into the main oil gallery; the controller compares its reading with a model of expected pressure at the present speed and oil temperature.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Sensor aged, contaminated or out of calibration
- A real fault in the system being measured
Checks
- 1Compare the engine oil pressure sensor reading with a reference gauge or thermometer with the engine off and cold.
- 2Check the system around the engine oil pressure sensor for leaks, restrictions or contamination.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 100 FMI 21Oil Pressure too Low
Detroit lists SPN 100 FMI 21 as "Oil Pressure too Low". The MCM found the engine oil pressure sensor value drifted away from what the engine state says it should be. The oil pressure sensor screws into the main oil gallery; the controller compares its reading with a model of expected pressure at the present speed and oil temperature.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Sensor aged, contaminated or out of calibration
- A real fault in the system being measured
Checks
- 1Compare the engine oil pressure sensor reading with a reference gauge or thermometer with the engine off and cold.
- 2Check the system around the engine oil pressure sensor for leaks, restrictions or contamination.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 100 FMI 31Engine Oil Pressure Rationality Error Low
Same failure as SPN 100 FMI 14 ("Engine Oil Pressure Sensor Plausibility Check Error") on a sibling part: Detroit lists SPN 100 FMI 31 as "Engine Oil Pressure Rationality Error Low". The oil pressure sensor screws into the main oil gallery; the controller compares its reading with a model of expected pressure at the present speed and oil temperature.· Real conditionReal conditionCheck soonCauses
- The causes listed under SPN 100 FMI 14, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 100 FMI 14, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 175 FMI 0Oil Temperature High Warning
Detroit lists SPN 175 FMI 0 as "Oil Temperature High Warning". The MCM reports that the measured value itself is out of its normal range; the engine oil pressure sensor may be correct and a real condition may exist. Engine oil temperature is read in the oil gallery area and is used to correct oil pressure limits and protect the engine from hot oil.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the engine oil pressure sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the engine oil pressure sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 175 FMI 2Engine Oil Temperature Sensor General Temperature Plausibility Error
Same failure as SPN 100 FMI 14 ("Engine Oil Pressure Sensor Plausibility Check Error") on a sibling part: Detroit lists SPN 175 FMI 2 as "Engine Oil Temperature Sensor General Temperature Plausibility Error". Engine oil temperature is read in the oil gallery area and is used to correct oil pressure limits and protect the engine from hot oil.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 100 FMI 14, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 100 FMI 14, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 175 FMI 3Short to Voltage or Open on Engine Oil Temperature Sensor Circuit
Same failure as SPN 100 FMI 3 ("Engine Oil Pressure Sensor Circuit Failed High") on a sibling part: Detroit lists SPN 175 FMI 3 as "Short to Voltage or Open on Engine Oil Temperature Sensor Circuit". Engine oil temperature is read in the oil gallery area and is used to correct oil pressure limits and protect the engine from hot oil.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 100 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 100 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 175 FMI 4Engine Oil Temperature Circuit Failed Low
Same failure as SPN 100 FMI 4 ("Engine Oil Pressure Sensor Circuit Failed Low") on a sibling part: Detroit lists SPN 175 FMI 4 as "Engine Oil Temperature Circuit Failed Low". Engine oil temperature is read in the oil gallery area and is used to correct oil pressure limits and protect the engine from hot oil.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 100 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 100 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 175 FMI 15Engine Oil Temperature High Pre Warning
Detroit lists SPN 175 FMI 15 as "Engine Oil Temperature High Pre Warning". The MCM reports that the measured value itself is out of its normal range; the engine oil pressure sensor may be correct and a real condition may exist. Engine oil temperature is read in the oil gallery area and is used to correct oil pressure limits and protect the engine from hot oil.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the engine oil pressure sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the engine oil pressure sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 175 FMI 18Engine Oil Temperature Rises Too Slow or Not At All
Detroit lists SPN 175 FMI 18 as "Engine Oil Temperature Rises Too Slow or Not At All". The MCM reports that the measured value itself is out of its normal range; the engine oil pressure sensor may be correct and a real condition may exist. Engine oil temperature is read in the oil gallery area and is used to correct oil pressure limits and protect the engine from hot oil.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the engine oil pressure sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the engine oil pressure sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 175 FMI 20Engine Oil Temperature Signal Not Plausible
Same failure as SPN 100 FMI 14 ("Engine Oil Pressure Sensor Plausibility Check Error") on a sibling part: Detroit lists SPN 175 FMI 20 as "Engine Oil Temperature Signal Not Plausible". Engine oil temperature is read in the oil gallery area and is used to correct oil pressure limits and protect the engine from hot oil.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 100 FMI 14, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 100 FMI 14, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 5527 FMI 16OPC Inductor Temperature too High
Detroit lists SPN 5527 FMI 16 as "OPC Inductor Temperature too High". The MCM reports that the measured value itself is out of its normal range; the engine oil pressure sensor may be correct and a real condition may exist. The oil pressure control inductor is a part of the oil pressure regulation; too high a temperature there shows an overload.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the engine oil pressure sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the engine oil pressure sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 521136 FMI 3Oil Pressure Control Circuit Failed High
Same failure as SPN 100 FMI 3 ("Engine Oil Pressure Sensor Circuit Failed High") on a sibling part: Detroit lists SPN 521136 FMI 3 as "Oil Pressure Control Circuit Failed High". The oil pressure control circuit is driven by the MCM; high, low or open entries are electrical.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 100 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 100 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 521136 FMI 4Oil Pressure Control Circuit Failed Low
Same failure as SPN 100 FMI 4 ("Engine Oil Pressure Sensor Circuit Failed Low") on a sibling part: Detroit lists SPN 521136 FMI 4 as "Oil Pressure Control Circuit Failed Low". The oil pressure control circuit is driven by the MCM; high, low or open entries are electrical.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 100 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 100 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 521136 FMI 5Oil Pressure Control Circuit Failed Open
Detroit lists SPN 521136 FMI 5 as "Oil Pressure Control Circuit Failed Open". The MCM detected an open circuit on the engine oil pressure sensor line, so the signal floats or is missing. The oil pressure control circuit is driven by the MCM; high, low or open entries are electrical.· Open circuitOpen circuitCheck soonCauses
- Broken wire or a pushed-out pin in the engine oil pressure sensor connector
- Corroded terminal or a failed sensor
Checks
- 1Check continuity of every wire between the engine oil pressure sensor connector and the MCM connector.
- 2Wiggle the harness and connector while watching the live value for dropouts.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Shared checks
Checks, in order
- 1Check the oil level and condition on the dipstick before anything electrical, and look for fuel or coolant in the oil.
- 2Read the live oil pressure in the diagnostic tool at idle and at high idle and compare it with a mechanical gauge at the gallery port.
- 3Unplug the oil pressure sensor and inspect the connector for oil, bent pins and green corrosion.
- 4Check the sensor supply, return and signal wires back to the MCM for chafing and for continuity.
- 5Replace the sensor only after the mechanical gauge proves the pressure is right and the wiring tests good.
Causes
- Genuinely low oil level or low oil pressure from a worn pump, bearings or a stuck relief valve
- Oil pressure sensor or its connector damaged by oil, heat or vibration
- Chafed sensor wiring shorting to ground or to the 5 V supply
- Wrong oil grade or fuel-diluted oil behind a plausibility code
Most common here: real condition (9 of 23)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: The low-oil-pressure or stop-engine lamp may come on, and the engine may be derated or shut down if the pressure is genuinely low.
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Detroit Diesel DD15 Gen 5 (2023) Fault Codes List, Diesel Repair (SPN/FMI with Detroit descriptions)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
