Detroit · Engine speed and position
Detroit Crankshaft and camshaft position sensors fault codes
The MCM times injection from the crankshaft and camshaft position sensors. Detroit logs open circuits, noisy or missing signals and a mismatch between the two as separate codes.
Where to read it
Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.
What do these codes mean?
Detroit codes SPN 636 FMI 1 to SPN 520322 FMI 31 are all about the crankshaft and camshaft position sensors. The most common failure type is erratic or implausible (6 of 13); none needs an immediate stop. Start with this check: check the sensor mounting, air gap and tip for metal fuzz or damage.
How urgent are they?
None of the 13 codes here means stop now; all 13 can wait until the shift ends, but find the cause before the next one.
- Check soon13
What should I check first?
Check the sensor mounting, air gap and tip for metal fuzz or damage.
Shared checks13 of 13
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Detroit SPN 636 FMI 1Crankshaft Position Sensor Signal Voltage Too Low
Detroit lists SPN 636 FMI 1 as "Crankshaft Position Sensor Signal Voltage Too Low". The MCM reports that the measured value itself is out of its normal range; the position sensor may be correct and a real condition may exist. The crankshaft position sensor reads the teeth on the flywheel or gear and gives the controller engine speed and the crank angle for injection timing.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the position sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the position sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 636 FMI 2No Match of Camshaft and Crankshaft Signals
Detroit lists SPN 636 FMI 2 as "No Match of Camshaft and Crankshaft Signals". The MCM judged the position sensor reading erratic or not plausible compared with other sensors or its own history. The crankshaft position sensor reads the teeth on the flywheel or gear and gives the controller engine speed and the crank angle for injection timing.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting position sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the position sensor reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 636 FMI 3Crankshaft Position Sensor Has an Open Circuit
Detroit lists SPN 636 FMI 3 as "Crankshaft Position Sensor Has an Open Circuit". The MCM saw the position sensor signal above its valid range. That usually means the signal wire is shorted to a supply voltage or is open at the sensor. The crankshaft position sensor reads the teeth on the flywheel or gear and gives the controller engine speed and the crank angle for injection timing.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to the 5 V supply or open between the position sensor and the MCM
- The position sensor has failed inside
Checks
- 1Unplug the position sensor and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
- 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 636 FMI 8Crankshaft Position Sensor Time Out
Detroit lists SPN 636 FMI 8 as "Crankshaft Position Sensor Time Out". The MCM judged the position sensor reading erratic or not plausible compared with other sensors or its own history. The crankshaft position sensor reads the teeth on the flywheel or gear and gives the controller engine speed and the crank angle for injection timing.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting position sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the position sensor reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 636 FMI 10Crankshaft Position Sensor Signal Erratic
Detroit lists SPN 636 FMI 10 as "Crankshaft Position Sensor Signal Erratic". The MCM judged the position sensor reading erratic or not plausible compared with other sensors or its own history. The crankshaft position sensor reads the teeth on the flywheel or gear and gives the controller engine speed and the crank angle for injection timing.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting position sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the position sensor reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 636 FMI 11Crankshaft Position Sensor - Sensor Failure
Detroit lists SPN 636 FMI 11 as "Crankshaft Position Sensor - Sensor Failure". The MCM judged the position sensor reading erratic or not plausible compared with other sensors or its own history. The crankshaft position sensor reads the teeth on the flywheel or gear and gives the controller engine speed and the crank angle for injection timing.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting position sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the position sensor reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 636 FMI 15No Match of Camshaft and Crankshaft Signals
Same failure as SPN 636 FMI 2 ("No Match of Camshaft and Crankshaft Signals") on a sibling part: Detroit lists SPN 636 FMI 15 as "No Match of Camshaft and Crankshaft Signals". The crankshaft position sensor reads the teeth on the flywheel or gear and gives the controller engine speed and the crank angle for injection timing.· Real conditionReal conditionCheck soonCauses
- The causes listed under SPN 636 FMI 2, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 636 FMI 2, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 723 FMI 8Camshaft Position Sensor Time Out
Same failure as SPN 636 FMI 8 ("Crankshaft Position Sensor Time Out") on a sibling part: Detroit lists SPN 723 FMI 8 as "Camshaft Position Sensor Time Out". The camshaft position sensor tells the controller which stroke the engine is on so it can phase the injection; it is read together with the crankshaft signal.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 636 FMI 8, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 636 FMI 8, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 723 FMI 10Camshaft Position Sensor Signal Erratic
Detroit lists SPN 723 FMI 10 as "Camshaft Position Sensor Signal Erratic". The MCM judged the position sensor reading erratic or not plausible compared with other sensors or its own history. The camshaft position sensor tells the controller which stroke the engine is on so it can phase the injection; it is read together with the crankshaft signal.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting position sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the position sensor reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 723 FMI 11Camshaft Position Sensor Failure
Detroit lists SPN 723 FMI 11 as "Camshaft Position Sensor Failure". The MCM judged the position sensor reading erratic or not plausible compared with other sensors or its own history. The camshaft position sensor tells the controller which stroke the engine is on so it can phase the injection; it is read together with the crankshaft signal.· Lost messageLost messageCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting position sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the position sensor reading with a second reference such as a gauge or another sensor on the engine.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Detroit SPN 723 FMI 31Backwards Running Engine Detected
Detroit lists SPN 723 FMI 31 as "Backwards Running Engine Detected". The MCM logged a condition on the position sensor; the title says what it measured. The camshaft position sensor tells the controller which stroke the engine is on so it can phase the injection; it is read together with the crankshaft signal.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the position sensor watches
- Sensor or wiring fault
Checks
- 1Read the live value and compare it with a reference.
- 2Check the connector and wiring.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 5444 FMI 1Engine Crankcase Breather Oil Separator Speed Too Low
Detroit lists SPN 5444 FMI 1 as "Engine Crankcase Breather Oil Separator Speed Too Low". The MCM reports that the measured value itself is out of its normal range; the position sensor may be correct and a real condition may exist. The crankcase breather oil separator is driven at a speed the MCM monitors; low speed means it is slowed or jammed.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the position sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the position sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 520322 FMI 31No Match of Camshaft and Crankshaft Signals - Engine Cold
Detroit lists SPN 520322 FMI 31 as "No Match of Camshaft and Crankshaft Signals - Engine Cold". The MCM logged a condition on the position sensor; the title says what it measured. The camshaft and crankshaft signals do not match while the engine is cold, which points to a timing or sensor problem.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the position sensor watches
- Sensor or wiring fault
Checks
- 1Read the live value and compare it with a reference.
- 2Check the connector and wiring.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Shared checks
Checks, in order
- 1Check the sensor mounting, air gap and tip for metal fuzz or damage.
- 2Inspect the connector and wiring for oil, chafing and pushed-back pins.
- 3Compare the engine speed readings from the crank and the cam in the tool while cranking.
- 4Inspect the flywheel or gear teeth and the cam gear for damage or missing teeth.
- 5Replace the sensor that fails the wiring and resistance checks and recheck the timing signals.
Causes
- Crankshaft or camshaft sensor damaged, loose or covered in metal debris
- Sensor connector or harness damaged near the flywheel housing or gear case
- Tone wheel or timing gear problem, such as a damaged reluctor
- Backwards running or kickback during starting
Most common here: erratic or implausible (6 of 13)
Watch the live value on the service tool while you flex the harness and tap the connector.
When to stop
You'll notice: Long cranking or no start, a stalled engine, an engine that runs rough or starts in limp mode.
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Detroit Diesel DD15 Gen 5 (2023) Fault Codes List, Diesel Repair (SPN/FMI with Detroit descriptions)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
