Detroit · Cooling system
Detroit Coolant temperature, level and thermostat fault codes
The MCM watches the coolant outlet temperature, the coolant inlet temperature and the coolant level sensor in the surge tank. Detroit also logs thermostat behaviour here, because a thermostat that stays open shows up as coolant that warms too slowly.
Where to read it
Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.
What do these codes mean?
Detroit codes SPN 110 FMI 0 to SPN 4193 FMI 20 are all about the coolant temperature, level and thermostat. The most common failure type is real condition (7 of 20); 2 need an immediate stop. Start with this check: check the coolant level cold, the surge tank cap and look for external leaks, oil in the coolant and white deposits at joints.
How urgent are they?
2 of 20 codes here mean stop now; the other 18 can wait until the shift ends, but find the cause before the next one.
- Stop now2
- Check soon18
What should I check first?
Check the coolant level cold, the surge tank cap and look for external leaks, oil in the coolant and white deposits at joints.
Shared checks20 of 20
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Detroit SPN 110 FMI 0Coolant Temperature High
Detroit lists SPN 110 FMI 0 as "Coolant Temperature High". The MCM reports that the measured value itself is out of its normal range; the coolant sensor may be correct and a real condition may exist. Coolant outlet temperature is read near the thermostat housing and drives the derate, the fan and the thermostat monitoring.· Real conditionReal conditionStop nowCauses
- A real fault in the system the coolant sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the coolant sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 110 FMI 3Engine Coolant Outlet Temperature Circuit Short to Voltage or Open
Detroit lists SPN 110 FMI 3 as "Engine Coolant Outlet Temperature Circuit Short to Voltage or Open". The MCM saw the coolant sensor signal above its valid range. That usually means the signal wire is shorted to a supply voltage or is open at the sensor. Coolant outlet temperature is read near the thermostat housing and drives the derate, the fan and the thermostat monitoring.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to the 5 V supply or open between the coolant sensor and the MCM
- The coolant sensor has failed inside
Checks
- 1Unplug the coolant sensor and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
- 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 110 FMI 4Engine Coolant Outlet Temperature Circuit Failed Low
Detroit lists SPN 110 FMI 4 as "Engine Coolant Outlet Temperature Circuit Failed Low". The MCM saw the coolant sensor signal below its valid range. That usually means the signal wire is shorted to ground or the sensor has failed. Coolant outlet temperature is read near the thermostat housing and drives the derate, the fan and the thermostat monitoring.· Shorted lowShorted lowCheck soonCauses
- Signal wire chafed against the engine and shorted to ground
- The coolant sensor has failed inside or its supply wire is open
Checks
- 1Unplug the coolant sensor and check whether the signal rises; if it stays low the harness is shorted to ground.
- 2Check the sensor supply at the connector with the key on and trace it back to the MCM if it is missing.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 110 FMI 9Coolant Temperature Signal Not Available via Controller Area Network (CAN)
Detroit lists SPN 110 FMI 9 as "Coolant Temperature Signal Not Available via Controller Area Network (CAN)". The MCM lost the coolant sensor signal completely. Coolant outlet temperature is read near the thermostat housing and drives the derate, the fan and the thermostat monitoring.· Lost messageLost messageCheck soonCauses
- Signal path broken at the connector or the harness
- Failed sensor or module
Checks
- 1Check the connector and the power supply to the coolant sensor.
- 2Check the signal wire to the MCM for an open.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Detroit SPN 110 FMI 16Coolant Temperature High Alarm
Detroit lists SPN 110 FMI 16 as "Coolant Temperature High Alarm". The MCM reports that the measured value itself is out of its normal range; the coolant sensor may be correct and a real condition may exist. Coolant outlet temperature is read near the thermostat housing and drives the derate, the fan and the thermostat monitoring.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the coolant sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the coolant sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 110 FMI 18Failed Coolant Thermostat (Coolant Heat Up Too Slow Compared to Modeled Coolant Temperature)
Detroit lists SPN 110 FMI 18 as "Failed Coolant Thermostat (Coolant Heat Up Too Slow Compared to Modeled Coolant Temperature)". The MCM reports that the measured value itself is out of its normal range; the coolant sensor may be correct and a real condition may exist. Coolant outlet temperature is read near the thermostat housing and drives the derate, the fan and the thermostat monitoring.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the coolant sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the coolant sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 110 FMI 20Engine Coolant Outlet Temperature Sensor General Temperature Plausibility Error
Detroit lists SPN 110 FMI 20 as "Engine Coolant Outlet Temperature Sensor General Temperature Plausibility Error". The MCM found the coolant sensor value drifted away from what the engine state says it should be. Coolant outlet temperature is read near the thermostat housing and drives the derate, the fan and the thermostat monitoring.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Sensor aged, contaminated or out of calibration
- A real fault in the system being measured
Checks
- 1Compare the coolant sensor reading with a reference gauge or thermometer with the engine off and cold.
- 2Check the system around the coolant sensor for leaks, restrictions or contamination.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 111 FMI 1Coolant Level Very Low
The MCM sees the coolant level very low in the surge tank. This is a protection fault, because low coolant can overheat and damage the engine.· Real conditionReal conditionStop nowCauses
- Coolant leak from a hose, the radiator or the water pump
- Air in the system
- Coolant level sensor fault
Checks
- 1Stop the engine and check the coolant level when it is cold, not when it is hot.
- 2Look for leaks at hoses, the radiator, the heater circuit and the water pump.
- 3Check the level sensor connector in the surge tank for corrosion.
- 4Top up with the right coolant and bleed air from the system, then recheck the level.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 111 FMI 3Coolant Level Circuit Failed High
Same failure as SPN 110 FMI 3 ("Engine Coolant Outlet Temperature Circuit Short to Voltage or Open") on a sibling part: Detroit lists SPN 111 FMI 3 as "Coolant Level Circuit Failed High". The coolant level sensor sits in the surge tank and only reports a low level once the tank is nearly empty, so a low reading means a real loss or an air pocket.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 110 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 110 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 111 FMI 4Coolant level Sensor Circuit Failed Low
Same failure as SPN 110 FMI 4 ("Engine Coolant Outlet Temperature Circuit Failed Low") on a sibling part: Detroit lists SPN 111 FMI 4 as "Coolant level Sensor Circuit Failed Low". The coolant level sensor sits in the surge tank and only reports a low level once the tank is nearly empty, so a low reading means a real loss or an air pocket.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 110 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 110 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 111 FMI 14Coolant Level Signal Erratic Data
Detroit lists SPN 111 FMI 14 as "Coolant Level Signal Erratic Data". The MCM judged the coolant sensor reading erratic or not plausible compared with other sensors or its own history. The coolant level sensor sits in the surge tank and only reports a low level once the tank is nearly empty, so a low reading means a real loss or an air pocket.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting coolant sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the coolant sensor reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 111 FMI 18Coolant Level Low
Detroit lists SPN 111 FMI 18 as "Coolant Level Low". The MCM reports that the measured value itself is out of its normal range; the coolant sensor may be correct and a real condition may exist. The coolant level sensor sits in the surge tank and only reports a low level once the tank is nearly empty, so a low reading means a real loss or an air pocket.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the coolant sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the coolant sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 1637 FMI 2Coolant Out Temperature Signal Not Plausible
Same failure as SPN 110 FMI 20 ("Engine Coolant Outlet Temperature Sensor General Temperature Plausibility Error") on a sibling part: Detroit lists SPN 1637 FMI 2 as "Coolant Out Temperature Signal Not Plausible". A second coolant outlet reading is compared with the main coolant temperature signal to check it is believable.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 110 FMI 20, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 110 FMI 20, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 1659 FMI 7Thermostat Cool Down
Detroit lists SPN 1659 FMI 7 as "Thermostat Cool Down". The MCM judged the coolant sensor reading erratic or not plausible compared with other sensors or its own history. The coolant temperature is watched after start to see whether the thermostat opens at the right time and the engine warms normally.· Part or controllerPart or controllerCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting coolant sensor or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the coolant sensor reading with a second reference such as a gauge or another sensor on the engine.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 1659 FMI 17Coolant Temperature Low Pre Fail
Detroit lists SPN 1659 FMI 17 as "Coolant Temperature Low Pre Fail". The MCM reports that the measured value itself is out of its normal range; the coolant sensor may be correct and a real condition may exist. The coolant temperature is watched after start to see whether the thermostat opens at the right time and the engine warms normally.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the coolant sensor measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the coolant sensor.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 1659 FMI 31Thermostat Cool Down
Same failure as SPN 1659 FMI 7 ("Thermostat Cool Down") on a sibling part: Detroit lists SPN 1659 FMI 31 as "Thermostat Cool Down". The coolant temperature is watched after start to see whether the thermostat opens at the right time and the engine warms normally.· Real conditionReal conditionCheck soonCauses
- The causes listed under SPN 1659 FMI 7, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 1659 FMI 7, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 4193 FMI 3Engine Coolant Inlet Temperature Circuit Failed High
Same failure as SPN 110 FMI 3 ("Engine Coolant Outlet Temperature Circuit Short to Voltage or Open") on a sibling part: Detroit lists SPN 4193 FMI 3 as "Engine Coolant Inlet Temperature Circuit Failed High". The coolant inlet temperature sensor reads the coolant returning to the engine and helps the MCM monitor cooling performance.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 110 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 110 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 4193 FMI 4Engine Coolant Inlet Temperature Circuit Failed Low
Same failure as SPN 110 FMI 4 ("Engine Coolant Outlet Temperature Circuit Failed Low") on a sibling part: Detroit lists SPN 4193 FMI 4 as "Engine Coolant Inlet Temperature Circuit Failed Low". The coolant inlet temperature sensor reads the coolant returning to the engine and helps the MCM monitor cooling performance.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 110 FMI 4, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 110 FMI 4, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 4193 FMI 14Engine Coolant Inlet Temperature Circuit Failed High
Same failure as SPN 110 FMI 3 ("Engine Coolant Outlet Temperature Circuit Short to Voltage or Open") on a sibling part: Detroit lists SPN 4193 FMI 14 as "Engine Coolant Inlet Temperature Circuit Failed High". The coolant inlet temperature sensor reads the coolant returning to the engine and helps the MCM monitor cooling performance.· OtherOtherCheck soonCauses
- The causes listed under SPN 110 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 110 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Detroit SPN 4193 FMI 20Coolant Inlet Temperature Signal Not Plausible
Same failure as SPN 110 FMI 20 ("Engine Coolant Outlet Temperature Sensor General Temperature Plausibility Error") on a sibling part: Detroit lists SPN 4193 FMI 20 as "Coolant Inlet Temperature Signal Not Plausible". The coolant inlet temperature sensor reads the coolant returning to the engine and helps the MCM monitor cooling performance.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 110 FMI 20, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 110 FMI 20, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Shared checks
Checks, in order
- 1Check the coolant level cold, the surge tank cap and look for external leaks, oil in the coolant and white deposits at joints.
- 2Compare the tool reading for coolant temperature with an infrared thermometer on the outlet housing at running temperature.
- 3Inspect the coolant temperature and level sensor connectors for pushed-back pins, moisture and corrosion.
- 4Measure the signal and return wires to the MCM for continuity and for shorts to ground or to the sensor supply.
- 5Confirm the fan engages at the right temperature and the thermostat opens before replacing any sensor.
Causes
- Low coolant from a leak, a loose cap or an air pocket after service
- Thermostat stuck open or closed, or an engine that warms too slowly
- Coolant temperature or level sensor connector corroded or wiring chafed
- Plugged radiator, failed fan or weak water pump behind a real overtemperature
Most common here: real condition (7 of 20)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: A coolant temperature or coolant level warning may show on the dash, and the engine may derate or shut down if the coolant is really hot or low.
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Detroit Diesel DD15 Gen 5 (2023) Fault Codes List, Diesel Repair (SPN/FMI with Detroit descriptions)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
