JLG · Platform / ground controls
JLG Fault Code 213
Footswitch faulty
What does JLG code 213 mean?
The two footswitch signals have been in the same state for too long, so the controller judges the footswitch faulty. Platform functions are locked out and the EMS must be recycled to clear the fault. Urgency: check soon - the machine may derate or limit a function. Check first: watch both footswitch inputs in the analyzer diagnostics; they should switch in opposite states as the pedal is pressed and released.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Watch both footswitch inputs in the analyzer diagnostics; they should switch in opposite states as the pedal is pressed and released
Then 4 more checksWhere this code shows
Turn the key on and watch the fault lamp or platform display.
Checks
0 of 5 done
Causes
- Footswitch contact stuck or worn so both signals match
- Footswitch cable pinched or broken inside the platform box
- Platform module connector corroded at the footswitch pins
- Water in the platform control box
1 more causeFewer causes
- Platform module input fault
How it failed
You'll notice: The footswitch is judged faulty and every platform function is locked out until EMS is recycled.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Footswitch, joysticks, steer switches and start sequence
- 2-3Boom function selection faultOtherCheck soon
- 2-4Steering digital inputs faultyOtherCheck soon
- 2-7Accelerator input faultyOtherCheck soon
- 0011Footswitch openOtherInformation
- 213Footswitch faultyOtherCheck soon
- 224Function problem - steer left permanently selectedOtherCheck soon
- 225Function problem - steer right permanently selectedOtherCheck soon
- 227Steer switches faultyReal conditionCheck soon
- 234Function switches faulty - check diagnostics/boomReal conditionCheck soon
Show the other 17 codesHide the other codes
- 2-1Footswitch or keyswitch faultReal conditionCheck soon
- 2-2Drive or steer selection faultOtherCheck soon
- 235Function switches locked - selected before aux powerOtherCheck soon
- 236Function switches locked - selected before start switchOtherCheck soon
- 237Start switch locked - selected before keyswitchOtherCheck soon
- 2211Footswitch interlock trippedReal conditionCheck soon
- 2212Drive locked - joystick moved before footswitchOtherCheck soon
- 2213Steer locked - selected before footswitchOtherCheck soon
- 2216Drive/steer joystick out of range highShorted highCheck soon
- 2217Drive/steer joystick centre tap badOtherCheck soon
- 2219Lift/swing joystick out of range highOtherCheck soon
- 2220Lift/swing joystick centre tap badOtherCheck soon
- 2221Lift/swing locked - joystick moved before footswitchOtherCheck soon
- 2222Waiting for footswitch to be openOtherInformation
- 2223Function switches locked - selected before enableOtherCheck soon
- 2224Footswitch selected before startOtherCheck soon
- 2310Function problem - ground enable permanently selectedOtherCheck soon
Related on Equipments Finder
Source
JLG 600S/660SJ Service and Maintenance Manual 3121298, section 6 (Table 6-8 Fault Code List)
This source lists 213 and its meaning. The guidance on this page is general, not taken from it.
The source covers: JLG 600S, 600SJ, 660SJ with newer module software; same DTC scheme on other JLG Control System booms, confirm in your manual.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
