JCB · Engine ECU (Dieselmax / Ecomax) - aftertreatment
JCB Fault Code P1471
DPF regeneration defective
What does JCB code P1471 mean?
The diesel particulate filter is not regenerating properly. Soot builds up and power may drop or limp mode starts. Urgency: check soon - the machine may derate or limit a function. Check first: read the soot load and the regeneration status live with the diagnostic tool.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Read the soot load and the regeneration status live with the diagnostic tool
Then 5 more checksWhere this code shows
Switch the key on and note any warning lamp or fault icon on the cluster.
Checks
0 of 6 done
Causes
- Machine used at low load and temperature for long periods so passive regeneration cannot occur
- Regeneration interrupted too often by the operator switching the engine off
- Faulty exhaust temperature sensor or differential pressure sensor misleading the ECU
- Fuel injection or EGR fault leaving too much soot
1 more causeFewer causes
- Blocked or damaged DPF
How it failed
You'll notice: The DPF lamp comes on, soot builds up and the engine loses power, then goes to limp mode if the filter cannot regenerate.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: DPF pressure, regeneration and exhaust temperature sensors
- P242B-17Catalyst temperature sensor plausibility above maximum thresholdLost messageCheck soon
- P242D-17T4 exhaust catalyst temperature voltage signal above maximumShorted highCheck soon
- P242B-23T4 exhaust catalyst temperature signal below minimumOtherCheck soon
- P1455DPF particulate over limitOtherCheck soon
- P1471DPF regeneration defectiveOtherCheck soon
- P2080Exhaust gas temperature sensor range/performanceOtherCheck soon
- P2428Exhaust gas temperature too highLost messageCheck soon
- P2428-17Exhaust catalyst temperature T4 signal above maximum limitOtherCheck soon
- P2452DPF differential pressure too lowReal conditionCheck soon
Show the other 13 codesHide the other codes
- P242FDPF soot load high due to ash buildupOtherCheck soon
- P242B-00SCR catalyst upstream temperature sensor plausibility errorErratic or implausibleCheck soon
- P242B-16Catalyst temperature sensor plausibility below minimum thresholdErratic or implausibleCheck soon
- P242C-16T4 exhaust catalyst temperature voltage signal below minimumOtherCheck soon
- P2453DPF differential pressure too highReal conditionCheck soon
- P2454DPF differential pressure sensor voltage too lowShorted lowCheck soon
- P2455DPF differential pressure sensor voltage highShorted highCheck soon
- P2456DPF differential pressure sensor zero-point learning failureErratic or implausibleCheck soon
- P2458DPF regeneration timeouts too frequentLost messageCheck soon
- P3419-87Error for particulate inlet pressureOtherCheck soon
- P3420-87Data length error for PROSCR3 regeneration frameOtherCheck soon
- P3421-87Timeout error for PROSCR3 regeneration frameLost messageCheck soon
- P3422-87Erroneous soot load message signalOtherCheck soon
Related on Equipments Finder
Source
Partao JCB fault code P1471 page
This source lists P1471 and its meaning. The guidance on this page is general, not taken from it.
The source covers: 406-409 SV, telehandlers, backhoe loaders, tracked and wheeled excavators.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
