JCB · Engine ECU (Dieselmax / Ecomax) - speed sensors
JCB Fault Code P0340
Camshaft position sensor circuit fault
What does JCB code P0340 mean?
The ECU gets no valid camshaft signal. It uses it for injection timing, so starting and running can suffer. Urgency: check soon - the machine may derate or limit a function. Check first: crank the engine and look at the live cam signal in the diagnostic tool.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Crank the engine and look at the live cam signal in the diagnostic tool
Then 5 more checksWhere this code shows
Switch the key on and note any warning lamp or fault icon on the cluster.
Checks
0 of 6 done
Causes
- Camshaft position sensor failed or its signal weak
- Broken wire or loose pin in the cam sensor connector
- Sensor tip dirty or oil contaminated
- Camshaft or cam gear damaged so the trigger signal is wrong
1 more causeFewer causes
- Cam sensor harness damaged near the front of the engine
How it failed
You'll notice: The engine may start but take longer to catch, and it can lose power or idle rough, because the ECU has no cam signal to know which cylinder is on compression.
Lost messageRead from how the source describes the code
A module stopped hearing another on the data link, or the data came late or garbled.
- Meter test
- Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
- Good result
- About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Engine speed and timing sensors, oil pressure and oil level
3 other codes on this part are also lost message (P250B, P0335, P0336). When they show together, start at the wiring and connector they share.
- P0325Accelerometer fault (signal to noise ratio too low at idle)Real conditionCheck soon
- P0330Knock sensor 1 circuit faultOtherCheck soon
- P0335Crankshaft position sensor circuit faultLost messageStop now
- P0336Crankshaft sensor signal faultLost messageStop now
- P0340Camshaft position sensor circuit faultLost messageCheck soon
- P0341Camshaft position sensor A range/performanceErratic or implausibleCheck soon
- P0371Excessive pulses on crankshaft sensor signal AOtherCheck soon
- P0372Too few pulses on crankshaft sensor signal AOtherCheck soon
- P0374No pulses on crankshaft sensor signal AOpen circuitCheck soon
Show the other 6 codesHide the other codes
- P0016Crank and cam position correlation faultOtherCheck soon
- P250BEngine oil level low at key-onLost messageCheck soon
- P0520Low oil pressure warning lamp control circuit faultOtherInformation
- P0521Engine oil pressure sensor or switch range/performanceErratic or implausibleCheck soon
- P0522High oil pressureOtherCheck soon
- P0523Low oil pressureShorted highStop now
Related on Equipments Finder
Source
Partao JCB fault code P0340 page
This source lists P0340 and its meaning. The guidance on this page is general, not taken from it.
The source covers: 3CX, 4CX, JS130-JS230, TM220, telehandlers.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
