EF Logo

J1939 · Cooling

SPN 4193 Fault Code

Engine coolant inlet temperature

What does SPN 4193 mean?

Temperature of the coolant entering the engine, read by a sensor in the inlet pipe and used for cooling and fan control. How urgent it is depends on the FMI after SPN 4193 - pick it below. Check first: compare the inlet temperature with the outlet temperature after a cold soak; they should match within a few degrees.

FaultActiveSPN 4193FMI --J1939 engine ECU
SPN 4193
Engine coolant inlet temperature
FMI ?
How it failed - the number after the SPN

Can I keep running with it?

Depends on the FMI

How urgent it is depends on the FMI after SPN 4193 - pick it below.

What should I check first?

Compare the inlet temperature with the outlet temperature after a cold soak; they should match within a few degrees

Then 4 more checks
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect a J1939-capable scan tool to the 9-pin diagnostic port.

Which FMI shows after SPN 4193?

You'll notice: The ECM may run the fan at full speed or derate because it cannot trust the coolant inlet reading.

Find the number shown after SPN 4193 on your display.

  • 2SPN 4193 FMI 2: Engine coolant inlet temperature data is erratic, intermittent or incorrectErratic or implausibleDetroit DD15
  • 3SPN 4193 FMI 3: Engine coolant inlet temperature signal voltage is above normal, or the circuit is shorted to a high sourceShorted highDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
  • 4SPN 4193 FMI 4: Engine coolant inlet temperature signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
  • 10SPN 4193 FMI 10: Engine coolant inlet temperature is changing at an abnormal rateErratic or implausibleDetroit DD15
  • 14SPN 4193 FMI 14: Special-instruction fault for the Engine coolant inlet temperature; the maker lists a dedicated procedure for itOtherDetroit DD13 Gen 5, Detroit DD15 Gen 5
  • 17SPN 4193 FMI 17: Engine coolant inlet temperature is below the normal range, least severe levelReal conditionDetroit DD15
  • 20SPN 4193 FMI 20: Engine coolant inlet temperature has drifted highErratic or implausibleDetroit DD13 Gen 5, Detroit DD15 Gen 5

Checks

0 of 5 done

When to stop

Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.

How urgent SPN 4193 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Causes

  • Sensor element drifted
  • Connector filled with coolant vapour and corrosion
  • Thermostat stuck open so the inlet reads colder than modelled
  • Harness open or shorted

Source

Detroit Diesel DD15 2014-2016 fault codes list (Diesel Laptops)

This list names SPN 4193 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.

The source covers: Detroit DD13, Detroit DD15; same SPN on other J1939 engines.

Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.