EF Logo

J1939 · Air intake

SPN 108 Fault Code

Barometric pressure

What does SPN 108 mean?

Outside air pressure, read by a sensor in the ECM or on the engine. The ECM uses it to correct fuelling, boost and aftertreatment control for altitude. How urgent it is depends on the FMI after SPN 108 - pick it below. Check first: key on, engine off: compare the barometric reading with the intake manifold pressure; the two should be almost equal.

FaultActiveSPN 108FMI --J1939 engine ECU
SPN 108
Barometric pressure
FMI ?
How it failed - the number after the SPN

Can I keep running with it?

Depends on the FMI

How urgent it is depends on the FMI after SPN 108 - pick it below.

What should I check first?

Key on, engine off: compare the barometric reading with the intake manifold pressure; the two should be almost equal

Then 4 more checks
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect a J1939-capable scan tool to the 9-pin diagnostic port.

Which FMI shows after SPN 108?

You'll notice: Barometric (ambient) pressure is misread, so the ECM miscalculates air density.

Find the number shown after SPN 108 on your display.

  • 2SPN 108 FMI 2: Data is erratic, intermittent or incorrectErratic or implausibleCummins ISX15, Mack MP8, Mack MP7, PACCAR MX-13 and 1 more
  • 3SPN 108 FMI 3: Signal voltage is above normal, or the circuit is shorted to a high sourceShorted highCummins ISX15, Detroit DD15, Detroit DD13 Gen 5, Detroit DD15 Gen 5 and 4 more
  • 4SPN 108 FMI 4: Signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowCummins ISX15, Detroit DD15, Detroit DD13, Detroit DD13 Gen 5 and 5 more
  • 10SPN 108 FMI 10: The value is changing at an abnormal rateErratic or implausiblePACCAR MX-13
  • 13SPN 108 FMI 13: Ambient pressure was not received over the CAN data linkPart or controllerDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5

Checks

0 of 5 done

When to stop

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

How urgent SPN 108 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Causes

  • Circuit (reads high or open): signal wire open or shorted to the 5 V reference at the barometric sensor or ECM-internal sensor connector
  • Circuit (reads low): signal shorted to ground or 5 V reference lost at the sensor
  • Sensor port blocked with dirt, water or insects, giving a stuck reading
  • Barometric data coming over the data link from another module that is itself faulty

Source

Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)

This list names SPN 108 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.

The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.

Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.