Hyundai · Machine codes (MCU, HCESPN)
Hyundai Fault Code 101‑3
Hydraulic oil temperature sensor circuit voltage above normal
What does Hyundai code 101-3 mean?
The MCU sees the hydraulic oil temperature signal at a voltage above the normal window, which it takes as a short to a high source or an open signal wire. Urgency: check soon - the machine may derate or limit a function. Check first: check the oil temperature reading on the cluster and compare it with an infrared reading on the hydraulic tank.
- 101
- Which machine signal is at fault
- FMI 3
- Voltage above normal or shorted high
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Check the oil temperature reading on the cluster and compare it with an infrared reading on the hydraulic tank
Then 4 more checksWhere this code shows
Turn the key on and open the fault code or diagnosis menu on the cluster.
Checks
0 of 5 done
Causes
- Hydraulic oil temperature sensor unplugged or connector pin pushed back
- Signal wire broken or shorted to a supply wire
- Sensor failed open
- MCU input damaged
How it failed
You'll notice: The hydraulic oil temperature reads off scale or reads zero and the fan may run harder than needed.
Shorted highRead from how the source describes the code
The signal sits at or near the supply voltage - more than a working sensor can send.
- Meter test
- Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
- Good result
- Open circuit (OL) between them. Any low reading is the short.
When to stop
Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Cooling fan, coolant and hydraulic oil temperature circuits
1 other code on this part is also shorted high (304-3). When they show together, start at the wiring and connector they share.
- 101-3Hydraulic oil temperature sensor circuit voltage above normalShorted highCheck soon
- 101-4Hydraulic oil temperature sensor circuit voltage below normalShorted lowCheck soon
- 145-5Engine cooling fan EPPR valve circuit current below normal or openOpen circuitCheck soon
- 145-6Engine cooling fan EPPR valve circuit current above normalShorted lowCheck soon
- 181-4Engine cooling fan reverse solenoid circuit voltage below normal, shorted to low source or openShorted lowCheck soon
- 181-6Engine cooling fan reverse solenoid circuit current above normalShorted lowCheck soon
- 183-4Engine cooling fan reverse driving status signal circuit voltage below normal, shorted to low source or openShorted lowCheck soon
- 183-6Engine cooling fan reverse driving status signal circuit current above normalShorted lowCheck soon
- 304-3Engine coolant temperature sensor circuit voltage above normalShorted highCheck soon
- 304-4Engine coolant temperature sensor circuit voltage below normalShorted lowCheck soon
- 318-8Engine cooling fan speed signal error, abnormal frequency or pulse widthErratic or implausibleCheck soon
Other Hyundai codes: Machine codes (MCU, HCESPN)
- 172-4Boom up lever detent solenoid circuit voltage below normal, shorted to low source or open
- 172-6Boom up lever detent solenoid circuit current above normal
- 173-4Boom down lever detent solenoid circuit voltage below normal, shorted to low source or open
- 173-6Boom down lever detent solenoid circuit current above normal
- 174-4Bucket lever detent solenoid circuit voltage below normal, shorted to low source or open
Related on Equipments Finder
Source
This source lists 101-3 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Hyundai HL757-9 wheel loader (manual covers the MCU machine table and the TCU transmission table).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
