Genie · Controls and ECM faults (C)
Genie Fault Code C058
Drive controller voltage out of range (DCON type 04)
What does Genie code C058 mean?
The drive controller sees battery voltage out of range, either too high or too low. All functions are blocked until the voltage is back in range. Urgency: stop now - shut down and fix before working on. Check first: unplug the charger from the machine, then cycle the key switch and see if the code clears.
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Unplug the charger from the machine, then cycle the key switch and see if the code clears.
Then 4 more checksWhere this code shows
Scissors: read the code on the platform LED display or the ground control LCD.
Checks
0 of 5 done
Causes
- Charger connected to the machine
- Batteries too low or over-charged
- Loose or corroded battery or controller terminals
- Drive controller internal fault
How it failed
You'll notice: Every function is blocked because the drive controller sees battery voltage out of range.
Real conditionRead from how the source describes the code
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Controllers, link, calibration and ECM self-checks
10 other codes on this part are also real condition (C004, C005, C006, C010 and more). When they show together, start at the wiring and connector they share.
- C029Outrigger sensor not calibratedPart or controllerCheck soon
- C053PCON-GCON software mismatchPart or controllerStop now
- C055Drive controller hardware failure (DCON type 01)Real conditionStop now
- C056Drive controller setup failure (DCON type 02)Real conditionStop now
- C058Drive controller voltage out of range (DCON type 04)Real conditionStop now
- C059Drive controller capacitor charge failure (DCON type 05)Real conditionStop now
- C061Drive controller key switch or B+/B- open (DCON type 07)Real conditionStop now
- C063Drive controller CAN fault (DCON type 09)Lost messageStop now
- C064Drive controller thermal sensor (DCON type 10)Real conditionStop now
Show the other 15 codesHide the other codes
- C001GCON ECM CRC errorPart or controllerStop now
- C004GCON master switch errorReal conditionStop now
- C005GCON safety switch errorReal conditionStop now
- C006GCON input redundancy errorReal conditionStop now
- C007GCON inter-processor communication errorLost messageStop now
- C009GCON ECM fault type 9Part or controllerStop now
- C010Secondary processor not programmedReal conditionStop now
- C021PCON not detectedLost messageStop now
- C023Machine model faultReal conditionStop now
- C025Platform overload not calibratedPart or controllerStop now
- C028Service override mode onOtherCheck soon
- H067Motor controller enable: short to battery negativeShorted highStop now
- H069Motor controller enable: short to battery positiveShorted highStop now
- H070Motor controller throttle: short to battery negativeShorted highStop now
- H072Motor controller throttle: short to battery positiveShorted highStop now
Related on Equipments Finder
Source
This source lists C058 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Genie GS-1530/1532/1930/1932/2032/2632 slab scissors with SmartLink (GSDS) controls.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
