EF Logo

Genie · Control system fault codes (ALC-500 red/yellow LED)

Genie ALC-500 boom, rotate and drive valves fault codes

Each ALC-500 function has a directional valve and a proportional flow valve: primary up/down (error sources 22 and 23), secondary up/down (32 and 33), turntable rotate (42 and 43), and the drive flow valve or EDC that sets pump displacement (53). The controller flags a valve that is working outside its limits, a value too high or too low, or a threshold that was never calibrated.

FaultCheck22-21Genie · ALC-500 boom, rotate and drive valves
Code shows hereFAULT22-21

Where this code shows

Scissors: read the code on the platform LED display or the ground control LCD.

What do these codes mean?

Genie codes 22-21 to 53-17 are all about the aLC-500 boom, rotate and drive valves. Most are real condition faults; none needs an immediate stop. Start with this check: command the function slowly from the platform and listen for the valve; no click or a late response points at its coil or the wiring to it.

How urgent are they?

None of the 15 codes here means stop now; 11 can wait until the shift ends, but find the cause before the next one; 4 are information only.

  • Check soon11
  • Info4

What should I check first?

Command the function slowly from the platform and listen for the valve; no click or a late response points at its coil or the wiring to it.

Shared checks

15 of 15

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Genie 22-21Primary up/down directional valves fault

    A primary up/down directional valve is working outside its limits and the alarm sounds.· Other
    Check soon

    Causes

    • Up or down directional solenoid open circuit or shorted
    • Wiring or connector fault at the directional valve block
    • Spool stuck in the directional valve

    Checks

    1. 1Check the up and down directional valve coils and their plugs for corrosion and loose pins.
    2. 2Measure the coil resistance; the manual lists 5 to 7 ohm for the 10 V three-position valves, plus or minus 30 percent.
    3. 3Inspect the harness for chafing near the valve manifold.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie 23-12Primary up/down flow valve value too high

    The primary up/down flow valve is working outside its limits and the alarm sounds.· Real condition
    Check soon

    Causes

    • Proportional flow coil open or shorted
    • Spool contaminated by dirty oil
    • Controller output damaged

    Checks

    1. 1Measure the proportional coil resistance against the coil table in the manual, about 4 to 6 ohm for the 12 V proportional valves.
    2. 2Check the flow valve coil plug for corrosion and a loose fit.
    3. 3Inspect the manifold harness for crush damage.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Genie 23-15Primary up/down flow valve value too low

    The primary up/down flow valve is operating outside its limits with a value that is too low.· Real condition
    Check soon

    Causes

    • Valve wiring open or coil damaged
    • Controller output fault

    Checks

    1. 1Check the valve coil and wiring.
    2. 2Cycle power off and on after repair.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Genie 23-17Primary up/down flow valve not calibrated

    The primary up/down flow valve has no threshold calibration.· Part or controller
    Info

    Causes

    • Primary up and down flow valve or coil replaced without calibrating the threshold
    • Controller reset cleared the stored threshold
    • Flow valve coil connector loose

    Checks

    1. 1Run the primary up and down valve threshold calibration from the service menu.
    2. 2Lift the boom slowly and check the movement starts gently, not with a jerk.
    3. 3Check the flow valve coil plug is fully seated on the manifold.
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Genie 32-21Secondary up/down directional valves fault

    The secondary up/down directional valves are operating outside their limits.· Other
    Check soon

    Causes

    • Valve coil or connector damaged
    • Valve wiring shorted or open

    Checks

    1. 1Measure the valve coil resistance and check the wiring.
    2. 2Cycle power off and on after repair.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie 33-12Secondary up/down flow valve value too high

    The secondary up/down flow valve is operating outside its limits with a value that is too high.· Real condition
    Check soon

    Causes

    • Valve wiring shorted or coil damaged
    • Controller output fault

    Checks

    1. 1Check the valve coil and wiring.
    2. 2Cycle power off and on after repair.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Genie 33-15Secondary up/down flow valve value too low

    The secondary up/down flow valve is operating outside its limits with a value that is too low.· Real condition
    Check soon

    Causes

    • Valve wiring open or coil damaged
    • Controller output fault

    Checks

    1. 1Check the valve coil and wiring.
    2. 2Cycle power off and on after repair.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Genie 33-17Secondary up/down flow valve not calibrated

    The secondary up/down flow valve threshold has not been calibrated.· Other
    Info

    Causes

    • Valve replaced or controller reprogrammed
    • Calibration lost after a reset

    Checks

    1. 1Calibrate the valve threshold.
    2. 2Cycle power and confirm the code is gone.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie 42-21Turntable rotate directional valves fault

    The turntable rotate directional valves are operating outside their limits.· Other
    Check soon

    Causes

    • Valve coil or connector damaged
    • Valve wiring shorted or open

    Checks

    1. 1Measure the valve coil resistance and check the wiring.
    2. 2Cycle power off and on after repair.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie 43-12Turntable rotate flow valve value too high

    The turntable rotate flow valve is operating outside its limits with a value that is too high.· Real condition
    Check soon

    Causes

    • Valve wiring shorted or coil damaged
    • Controller output fault

    Checks

    1. 1Check the valve coil and wiring.
    2. 2Cycle power off and on after repair.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Genie 43-15Turntable rotate flow valve value too low

    The turntable rotate flow valve is operating outside its limits with a value that is too low.· Real condition
    Check soon

    Causes

    • Valve wiring open or coil damaged
    • Controller output fault

    Checks

    1. 1Check the valve coil and wiring.
    2. 2Cycle power off and on after repair.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Genie 43-17Turntable rotate flow valve not calibrated

    The turntable rotate flow valve threshold has not been calibrated.· Other
    Info

    Causes

    • Valve replaced or controller reprogrammed
    • Calibration lost after a reset

    Checks

    1. 1Calibrate the valve threshold.
    2. 2Cycle power and confirm the code is gone.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie 53-12Drive flow valve (EDC) value too high

    The drive flow valve (EDC) is operating outside its limits with a value that is too high.· Real condition
    Check soon

    Causes

    • Valve wiring shorted or coil damaged
    • Controller output fault

    Checks

    1. 1Check the valve coil and wiring.
    2. 2Cycle power off and on after repair.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Genie 53-15Drive flow valve (EDC) value too low

    The drive flow valve (EDC) is operating outside its limits with a value that is too low.· Real condition
    Check soon

    Causes

    • Valve wiring open or coil damaged
    • Controller output fault

    Checks

    1. 1Check the valve coil and wiring.
    2. 2Cycle power off and on after repair.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Genie 53-17Drive flow valve (EDC) not calibrated

    The drive flow valve (EDC) has no threshold calibration.· Part or controller
    Info

    Causes

    • EDC drive flow valve or coil replaced without calibration
    • Controller reset cleared the drive valve threshold
    • EDC valve connector loose or damaged

    Checks

    1. 1Run the drive flow valve (EDC) threshold calibration from the service menu.
    2. 2Check the machine moves off smoothly from standstill after calibrating.
    3. 3Check the EDC coil connector on the drive pump is seated and dry.
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

Shared checks

Checks, in order

  1. 1Command the function slowly from the platform and listen for the valve; no click or a late response points at its coil or the wiring to it.
  2. 2Measure the valve coil resistance and compare it with the coil table in the manual or with a good coil.
  3. 3Check the valve harness for chafing and the plug for corrosion.
  4. 4Run the valve threshold calibration from the service menu after replacing a coil or valve, then cycle the key switch.

Causes

  • Valve coil or wiring shorted or open
  • Valve threshold never calibrated after replacement
  • Valve spool dirty or sticking at small openings
  • ALC-500 output stage damaged (rare)

Most codes here: real condition (8 of 15)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: The function is erratic, limited or frozen at neutral and the alarm sounds.

Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.