EF Logo

Develon · Fuel system

Develon Injector drivers and misfire monitoring fault codes

Injector solenoid power stages, injector circuits and misfire counters for each cylinder, plus charge-circuit and injection monitoring. Cylinder numbers follow the table.

FaultCheckE000651Develon · Injector drivers and misfire monitoring
Code shows hereFAULTE000651

Where this code shows

Switch the key on and open the monitor fault or service menu on the gauge panel to see active codes.

What do these codes mean?

Develon codes E000651 to E520626 are all about the injector drivers and misfire monitoring. The most common failure type is open circuit (6 of 26); none needs an immediate stop. Start with this check: note the cylinder number in the code and compare its misfire count with the others.

How urgent are they?

None of the 26 codes here means stop now; all 26 can wait until the shift ends, but find the cause before the next one.

  • Check soon26

What should I check first?

Note the cylinder number in the code and compare its misfire count with the others.

Shared checks

26 of 26

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Develon E000651Injector solenoid driver cylinder 1 circuit

    Same failure as E000734 on the injector solenoid driver cylinder 1 circuit, a different part of the same kind as the solenoid powerstage 1 (cylinder 1).· Open circuit
    Check soon

    Causes

    • Fault in the injector solenoid driver cylinder 1 circuit or its wiring
    • Any cause listed under E000734

    Checks

    1. 1Check the injector solenoid driver cylinder 1 circuit connector and wiring first, then follow the checks listed under E000734.
    2. 2Clear the code and confirm whether E000651 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Develon E000652Injector solenoid driver cylinder 2 circuit

    Same failure as E000734 on the injector solenoid driver cylinder 2 circuit, a different part of the same kind as the solenoid powerstage 1 (cylinder 1).· Open circuit
    Check soon

    Causes

    • Fault in the injector solenoid driver cylinder 2 circuit or its wiring
    • Any cause listed under E000734

    Checks

    1. 1Check the injector solenoid driver cylinder 2 circuit connector and wiring first, then follow the checks listed under E000734.
    2. 2Clear the code and confirm whether E000652 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Develon E000653Injector solenoid driver cylinder 3 circuit

    Same failure as E000734 on the injector solenoid driver cylinder 3 circuit, a different part of the same kind as the solenoid powerstage 1 (cylinder 1).· Open circuit
    Check soon

    Causes

    • Fault in the injector solenoid driver cylinder 3 circuit or its wiring
    • Any cause listed under E000734

    Checks

    1. 1Check the injector solenoid driver cylinder 3 circuit connector and wiring first, then follow the checks listed under E000734.
    2. 2Clear the code and confirm whether E000653 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Develon E000654Injector solenoid driver cylinder 4 circuit

    Same failure as E000734 on the injector solenoid driver cylinder 4 circuit, a different part of the same kind as the solenoid powerstage 1 (cylinder 1).· Open circuit
    Check soon

    Causes

    • Fault in the injector solenoid driver cylinder 4 circuit or its wiring
    • Any cause listed under E000734

    Checks

    1. 1Check the injector solenoid driver cylinder 4 circuit connector and wiring first, then follow the checks listed under E000734.
    2. 2Clear the code and confirm whether E000654 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Develon E000655Injector solenoid driver cylinder 5 circuit

    Same failure as E000734 on the injector solenoid driver cylinder 5 circuit, a different part of the same kind as the solenoid powerstage 1 (cylinder 1).· Open circuit
    Check soon

    Causes

    • Fault in the injector solenoid driver cylinder 5 circuit or its wiring
    • Any cause listed under E000734

    Checks

    1. 1Check the injector solenoid driver cylinder 5 circuit connector and wiring first, then follow the checks listed under E000734.
    2. 2Clear the code and confirm whether E000655 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Develon E000656Injector solenoid driver cylinder 6 circuit

    Same failure as E000734 on the injector solenoid driver cylinder 6 circuit, a different part of the same kind as the solenoid powerstage 1 (cylinder 1).· Open circuit
    Check soon

    Causes

    • Fault in the injector solenoid driver cylinder 6 circuit or its wiring
    • Any cause listed under E000734

    Checks

    1. 1Check the injector solenoid driver cylinder 6 circuit connector and wiring first, then follow the checks listed under E000734.
    2. 2Clear the code and confirm whether E000656 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Develon E000734Solenoid powerstage 1 (Cylinder 1)

    A solenoid power stage for an injector cylinder is not working as commanded.· Other
    Check soon

    Causes

    • Open or shorted injector wiring or connector
    • Faulty injector coil
    • Driver fault in the controller

    Checks

    1. 1Check the injector connector for oil, corrosion and a loose pin.
    2. 2Measure injector coil resistance and compare with the manual.
    3. 3Run the cylinder cut-out test in the tool to confirm which cylinder is weak.
    4. 4Inspect the injector harness under the valve cover for rubbing.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E000735Solenoid powerstage 2 (Cylinder 5)

    Same failure as E000734 on the solenoid powerstage 2 (cylinder 5), a different part of the same kind as the solenoid powerstage 1 (cylinder 1).· Other
    Check soon

    Causes

    • Fault in the solenoid powerstage 2 (cylinder 5) or its wiring
    • Any cause listed under E000734

    Checks

    1. 1Check the solenoid powerstage 2 (cylinder 5) connector and wiring first, then follow the checks listed under E000734.
    2. 2Clear the code and confirm whether E000735 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E000736Solenoid powerstage 3 (Cylinder 3)

    Same failure as E000734 on the solenoid powerstage 3 (cylinder 3), a different part of the same kind as the solenoid powerstage 1 (cylinder 1).· Other
    Check soon

    Causes

    • Fault in the solenoid powerstage 3 (cylinder 3) or its wiring
    • Any cause listed under E000734

    Checks

    1. 1Check the solenoid powerstage 3 (cylinder 3) connector and wiring first, then follow the checks listed under E000734.
    2. 2Clear the code and confirm whether E000736 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E000737Solenoid powerstage 4 (Cylinder 6)

    Same failure as E000734 on the solenoid powerstage 4 (cylinder 6), a different part of the same kind as the solenoid powerstage 1 (cylinder 1).· Other
    Check soon

    Causes

    • Fault in the solenoid powerstage 4 (cylinder 6) or its wiring
    • Any cause listed under E000734

    Checks

    1. 1Check the solenoid powerstage 4 (cylinder 6) connector and wiring first, then follow the checks listed under E000734.
    2. 2Clear the code and confirm whether E000737 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E000738Solenoid powerstage 5 (Cylinder 2)

    Same failure as E000734 on the solenoid powerstage 5 (cylinder 2), a different part of the same kind as the solenoid powerstage 1 (cylinder 1).· Other
    Check soon

    Causes

    • Fault in the solenoid powerstage 5 (cylinder 2) or its wiring
    • Any cause listed under E000734

    Checks

    1. 1Check the solenoid powerstage 5 (cylinder 2) connector and wiring first, then follow the checks listed under E000734.
    2. 2Clear the code and confirm whether E000738 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E000739Solenoid powerstage 6 (Cylinder 4)

    Same failure as E000734 on the solenoid powerstage 6 (cylinder 4), a different part of the same kind as the solenoid powerstage 1 (cylinder 1).· Other
    Check soon

    Causes

    • Fault in the solenoid powerstage 6 (cylinder 4) or its wiring
    • Any cause listed under E000734

    Checks

    1. 1Check the solenoid powerstage 6 (cylinder 4) connector and wiring first, then follow the checks listed under E000734.
    2. 2Clear the code and confirm whether E000739 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E001322Monitoring Misfire detection multiple cylinder

    Same failure as E001323 on the monitoring misfire detection multiple cylinder, a different part of the same kind as the injection misfire detection cylinder 1.· Other
    Check soon

    Causes

    • Fault in the monitoring misfire detection multiple cylinder or its wiring
    • Any cause listed under E001323

    Checks

    1. 1Check the monitoring misfire detection multiple cylinder connector and wiring first, then follow the checks listed under E001323.
    2. 2Clear the code and confirm whether E001322 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E001323Injection Misfire detection cylinder 1

    The misfire monitor recorded combustion trouble in one cylinder.· Other
    Check soon

    Causes

    • Weak or sticking injector
    • Poor compression in that cylinder
    • Injector wiring fault
    • Fuel leak at that injector

    Checks

    1. 1Read the live misfire counts and compare the cylinders.
    2. 2Look for fuel leaks and injector return flow.
    3. 3Check the injector harness and connector.
    4. 4Check compression and valve condition if the misfire stays with the cylinder.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E001324Injection Misfire detection cylinder 5

    Same failure as E001323 on the injection misfire detection cylinder 5, a different part of the same kind as the injection misfire detection cylinder 1.· Other
    Check soon

    Causes

    • Fault in the injection misfire detection cylinder 5 or its wiring
    • Any cause listed under E001323

    Checks

    1. 1Check the injection misfire detection cylinder 5 connector and wiring first, then follow the checks listed under E001323.
    2. 2Clear the code and confirm whether E001324 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E001325Injection Misfire detection cylinder 3

    Same failure as E001323 on the injection misfire detection cylinder 3, a different part of the same kind as the injection misfire detection cylinder 1.· Other
    Check soon

    Causes

    • Fault in the injection misfire detection cylinder 3 or its wiring
    • Any cause listed under E001323

    Checks

    1. 1Check the injection misfire detection cylinder 3 connector and wiring first, then follow the checks listed under E001323.
    2. 2Clear the code and confirm whether E001325 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E001326Injection Misfire detection cylinder 6

    Same failure as E001323 on the injection misfire detection cylinder 6, a different part of the same kind as the injection misfire detection cylinder 1.· Other
    Check soon

    Causes

    • Fault in the injection misfire detection cylinder 6 or its wiring
    • Any cause listed under E001323

    Checks

    1. 1Check the injection misfire detection cylinder 6 connector and wiring first, then follow the checks listed under E001323.
    2. 2Clear the code and confirm whether E001326 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E001327Injection Misfire detection cylinder 2

    Same failure as E001323 on the injection misfire detection cylinder 2, a different part of the same kind as the injection misfire detection cylinder 1.· Other
    Check soon

    Causes

    • Fault in the injection misfire detection cylinder 2 or its wiring
    • Any cause listed under E001323

    Checks

    1. 1Check the injection misfire detection cylinder 2 connector and wiring first, then follow the checks listed under E001323.
    2. 2Clear the code and confirm whether E001327 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E001328Injection Misfire detection cylinder 4

    Same failure as E001323 on the injection misfire detection cylinder 4, a different part of the same kind as the injection misfire detection cylinder 1.· Other
    Check soon

    Causes

    • Fault in the injection misfire detection cylinder 4 or its wiring
    • Any cause listed under E001323

    Checks

    1. 1Check the injection misfire detection cylinder 4 connector and wiring first, then follow the checks listed under E001323.
    2. 2Clear the code and confirm whether E001328 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E010003Injection Nozzle Common 1 Drive System Fault

    Same failure as E000734 on the injection nozzle common 1 drive system fault, a different part of the same kind as the solenoid powerstage 1 (cylinder 1).· Other
    Check soon

    Causes

    • Fault in the injection nozzle common 1 drive system fault or its wiring
    • Any cause listed under E000734

    Checks

    1. 1Check the injection nozzle common 1 drive system fault connector and wiring first, then follow the checks listed under E000734.
    2. 2Clear the code and confirm whether E010003 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E010004Injection Nozzle Common 2 Drive System Fault

    Same failure as E000734 on the injection nozzle common 2 drive system fault, a different part of the same kind as the solenoid powerstage 1 (cylinder 1).· Other
    Check soon

    Causes

    • Fault in the injection nozzle common 2 drive system fault or its wiring
    • Any cause listed under E000734

    Checks

    1. 1Check the injection nozzle common 2 drive system fault connector and wiring first, then follow the checks listed under E000734.
    2. 2Clear the code and confirm whether E010004 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E010005Charge Circuit Fault Bank 1

    Same failure as E000734 on the charge circuit fault bank 1, a different part of the same kind as the solenoid powerstage 1 (cylinder 1).· Other
    Check soon

    Causes

    • Fault in the charge circuit fault bank 1 or its wiring
    • Any cause listed under E000734

    Checks

    1. 1Check the charge circuit fault bank 1 connector and wiring first, then follow the checks listed under E000734.
    2. 2Clear the code and confirm whether E010005 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E010006Charge Circuit Fault Bank 2

    Same failure as E000734 on the charge circuit fault bank 2, a different part of the same kind as the solenoid powerstage 1 (cylinder 1).· Other
    Check soon

    Causes

    • Fault in the charge circuit fault bank 2 or its wiring
    • Any cause listed under E000734

    Checks

    1. 1Check the charge circuit fault bank 2 connector and wiring first, then follow the checks listed under E000734.
    2. 2Clear the code and confirm whether E010006 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E010032QR Code Error

    Same failure as E000734 on the qr code error, a different part of the same kind as the solenoid powerstage 1 (cylinder 1).· Other
    Check soon

    Causes

    • Fault in the qr code error or its wiring
    • Any cause listed under E000734

    Checks

    1. 1Check the qr code error connector and wiring first, then follow the checks listed under E000734.
    2. 2Clear the code and confirm whether E010032 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E520624Monitoring of injection

    Same failure as E000734 on the monitoring of injection, a different part of the same kind as the solenoid powerstage 1 (cylinder 1).· Other
    Check soon

    Causes

    • Fault in the monitoring of injection or its wiring
    • Any cause listed under E000734

    Checks

    1. 1Check the monitoring of injection connector and wiring first, then follow the checks listed under E000734.
    2. 2Clear the code and confirm whether E520624 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E520626Injection bank

    Same failure as E000734 on the injection bank, a different part of the same kind as the solenoid powerstage 1 (cylinder 1).· Other
    Check soon

    Causes

    • Fault in the injection bank or its wiring
    • Any cause listed under E000734

    Checks

    1. 1Check the injection bank connector and wiring first, then follow the checks listed under E000734.
    2. 2Clear the code and confirm whether E520626 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Note the cylinder number in the code and compare its misfire count with the others.
  2. 2Inspect the injector harness and connector for oil, rub marks and corrosion.
  3. 3Run the cylinder cut-out or injector test, if the tool allows.
  4. 4Check compression and valve condition if the misfire stays with the cylinder.

Causes

  • Injector coil or wiring fault
  • Worn or sticking injector
  • Driver or charge-circuit fault in the controller

Most common here: open circuit (6 of 26)

Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

When to stop

You'll notice: Rough running, white or black smoke, noise and loss of power; the code usually names the cylinder.

Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.