EF Logo

Detroit · Engine sensors and levels

Detroit Engine oil pressure sensor and low oil pressure fault codes

The MCM reads the engine oil pressure sensor in the oil gallery and compares the value with what it expects for the engine speed and oil temperature. Detroit uses SPN 100 for the real low-pressure warnings and the derate, and for sensor, plausibility and parameter faults.

FaultStopSPN 100FMI 1Detroit · Engine oil pressure sensor and low oil pressure
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.

What do these codes mean?

Detroit codes SPN 100 FMI 0 to SPN 521136 FMI 5 are all about the engine oil pressure sensor and low oil pressure. The most common failure type is real condition (9 of 23); 3 need an immediate stop. Start with this check: check the oil level and condition on the dipstick before anything electrical, and look for fuel or coolant in the oil.

How urgent are they?

3 of 23 codes here mean stop now; the other 20 can wait until the shift ends, but find the cause before the next one.

  • Stop now3
  • Check soon20

What should I check first?

Check the oil level and condition on the dipstick before anything electrical, and look for fuel or coolant in the oil.

Shared checks

23 of 23

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Detroit SPN 100 FMI 0Oil Pressure Stuck

    Detroit lists SPN 100 FMI 0 as "Oil Pressure Stuck".· Real condition
    Stop now

    Causes

    • A real fault in the system the engine oil pressure sensor measures
    • Sensor reading skewed by a wiring or connector problem

    Checks

    1. 1Confirm the real value with a mechanical gauge or an independent reading before replacing the engine oil pressure sensor.
    2. 2Check the system for the condition the code describes and fix it first.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 100 FMI 1Low Engine Oil Pressure

    The MCM measured the engine oil pressure below the minimum it allows for the current engine speed.· Real condition
    Stop now

    Causes

    • Oil level too low, or oil thinned by fuel or coolant
    • Worn oil pump, worn main or rod bearings, or a stuck open relief valve
    • Blocked oil filter or a cooler passage restricted
    • Oil pressure sensor reading wrongly because of corrosion or wiring damage

    Checks

    1. 1Stop the engine and check the oil level and condition on the dipstick; look for a fuel smell and milky oil.
    2. 2Fit a mechanical gauge at the oil gallery port and compare it with the live value in the diagnostic tool at idle and at high idle.
    3. 3If the gauge shows good pressure but the tool does not, inspect the oil pressure sensor connector and wiring for oil and corrosion.
    4. 4Check the oil and filter service history and the oil grade used.
    5. 5If the gauge also reads low, stop running the engine and investigate the pump, bearings and relief valve.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 100 FMI 3Engine Oil Pressure Sensor Circuit Failed High

    Detroit lists SPN 100 FMI 3 as "Engine Oil Pressure Sensor Circuit Failed High".· Shorted high
    Check soon

    Causes

    • Signal wire shorted to the 5 V supply or open between the engine oil pressure sensor and the MCM
    • The engine oil pressure sensor has failed inside

    Checks

    1. 1Unplug the engine oil pressure sensor and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
    2. 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 100 FMI 4Engine Oil Pressure Sensor Circuit Failed Low

    Detroit lists SPN 100 FMI 4 as "Engine Oil Pressure Sensor Circuit Failed Low".· Shorted low
    Check soon

    Causes

    • Signal wire chafed against the engine and shorted to ground
    • The engine oil pressure sensor has failed inside or its supply wire is open

    Checks

    1. 1Unplug the engine oil pressure sensor and check whether the signal rises; if it stays low the harness is shorted to ground.
    2. 2Check the sensor supply at the connector with the key on and trace it back to the MCM if it is missing.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 100 FMI 10Low Oil Pressure Derate

    Detroit lists SPN 100 FMI 10 as "Low Oil Pressure Derate".· Erratic or implausible
    Check soon

    Causes

    • Loose or corroded connector causing a noisy signal
    • A drifting engine oil pressure sensor or a related fault in the part it measures

    Checks

    1. 1Watch the live value while wiggling the harness to find an intermittent connection.
    2. 2Compare the engine oil pressure sensor reading with a second reference such as a gauge or another sensor on the engine.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 100 FMI 13Parameterization for OPC Is Incorrect

    Detroit lists SPN 100 FMI 13 as "Parameterization for OPC Is Incorrect".· Part or controller
    Check soon

    Causes

    • Sensor aged, contaminated or out of calibration
    • A real fault in the system being measured

    Checks

    1. 1Compare the engine oil pressure sensor reading with a reference gauge or thermometer with the engine off and cold.
    2. 2Check the system around the engine oil pressure sensor for leaks, restrictions or contamination.
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Detroit SPN 100 FMI 14Engine Oil Pressure Sensor Plausibility Check Error

    Detroit lists SPN 100 FMI 14 as "Engine Oil Pressure Sensor Plausibility Check Error".· Erratic or implausible
    Check soon

    Causes

    • Loose or corroded connector causing a noisy signal
    • A drifting engine oil pressure sensor or a related fault in the part it measures

    Checks

    1. 1Watch the live value while wiggling the harness to find an intermittent connection.
    2. 2Compare the engine oil pressure sensor reading with a second reference such as a gauge or another sensor on the engine.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 100 FMI 15Engine Oil Pressure Rationality Error High

    Same failure as SPN 100 FMI 14 ("Engine Oil Pressure Sensor Plausibility Check Error") on a sibling part: Detroit lists SPN 100 FMI 15 as "Engine Oil Pressure Rationality Error High".· Real condition
    Check soon

    Causes

    • The causes listed under SPN 100 FMI 14, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 100 FMI 14, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 100 FMI 17Oil Pressure Very Low

    Detroit lists SPN 100 FMI 17 as "Oil Pressure Very Low".· Real condition
    Stop now

    Causes

    • A real fault in the system the engine oil pressure sensor measures
    • Sensor reading skewed by a wiring or connector problem

    Checks

    1. 1Confirm the real value with a mechanical gauge or an independent reading before replacing the engine oil pressure sensor.
    2. 2Check the system for the condition the code describes and fix it first.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 100 FMI 20Oil Pressure too High

    Detroit lists SPN 100 FMI 20 as "Oil Pressure too High".· Erratic or implausible
    Check soon

    Causes

    • Sensor aged, contaminated or out of calibration
    • A real fault in the system being measured

    Checks

    1. 1Compare the engine oil pressure sensor reading with a reference gauge or thermometer with the engine off and cold.
    2. 2Check the system around the engine oil pressure sensor for leaks, restrictions or contamination.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 100 FMI 21Oil Pressure too Low

    Detroit lists SPN 100 FMI 21 as "Oil Pressure too Low".· Erratic or implausible
    Check soon

    Causes

    • Sensor aged, contaminated or out of calibration
    • A real fault in the system being measured

    Checks

    1. 1Compare the engine oil pressure sensor reading with a reference gauge or thermometer with the engine off and cold.
    2. 2Check the system around the engine oil pressure sensor for leaks, restrictions or contamination.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 100 FMI 31Engine Oil Pressure Rationality Error Low

    Same failure as SPN 100 FMI 14 ("Engine Oil Pressure Sensor Plausibility Check Error") on a sibling part: Detroit lists SPN 100 FMI 31 as "Engine Oil Pressure Rationality Error Low".· Real condition
    Check soon

    Causes

    • The causes listed under SPN 100 FMI 14, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 100 FMI 14, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 175 FMI 0Oil Temperature High Warning

    Detroit lists SPN 175 FMI 0 as "Oil Temperature High Warning".· Real condition
    Check soon

    Causes

    • A real fault in the system the engine oil pressure sensor measures
    • Sensor reading skewed by a wiring or connector problem

    Checks

    1. 1Confirm the real value with a mechanical gauge or an independent reading before replacing the engine oil pressure sensor.
    2. 2Check the system for the condition the code describes and fix it first.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 175 FMI 2Engine Oil Temperature Sensor General Temperature Plausibility Error

    Same failure as SPN 100 FMI 14 ("Engine Oil Pressure Sensor Plausibility Check Error") on a sibling part: Detroit lists SPN 175 FMI 2 as "Engine Oil Temperature Sensor General Temperature Plausibility Error".· Erratic or implausible
    Check soon

    Causes

    • The causes listed under SPN 100 FMI 14, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 100 FMI 14, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 175 FMI 3Short to Voltage or Open on Engine Oil Temperature Sensor Circuit

    Same failure as SPN 100 FMI 3 ("Engine Oil Pressure Sensor Circuit Failed High") on a sibling part: Detroit lists SPN 175 FMI 3 as "Short to Voltage or Open on Engine Oil Temperature Sensor Circuit".· Shorted high
    Check soon

    Causes

    • The causes listed under SPN 100 FMI 3, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 100 FMI 3, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 175 FMI 4Engine Oil Temperature Circuit Failed Low

    Same failure as SPN 100 FMI 4 ("Engine Oil Pressure Sensor Circuit Failed Low") on a sibling part: Detroit lists SPN 175 FMI 4 as "Engine Oil Temperature Circuit Failed Low".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 100 FMI 4, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 100 FMI 4, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 175 FMI 15Engine Oil Temperature High Pre Warning

    Detroit lists SPN 175 FMI 15 as "Engine Oil Temperature High Pre Warning".· Real condition
    Check soon

    Causes

    • A real fault in the system the engine oil pressure sensor measures
    • Sensor reading skewed by a wiring or connector problem

    Checks

    1. 1Confirm the real value with a mechanical gauge or an independent reading before replacing the engine oil pressure sensor.
    2. 2Check the system for the condition the code describes and fix it first.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 175 FMI 18Engine Oil Temperature Rises Too Slow or Not At All

    Detroit lists SPN 175 FMI 18 as "Engine Oil Temperature Rises Too Slow or Not At All".· Real condition
    Check soon

    Causes

    • A real fault in the system the engine oil pressure sensor measures
    • Sensor reading skewed by a wiring or connector problem

    Checks

    1. 1Confirm the real value with a mechanical gauge or an independent reading before replacing the engine oil pressure sensor.
    2. 2Check the system for the condition the code describes and fix it first.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 175 FMI 20Engine Oil Temperature Signal Not Plausible

    Same failure as SPN 100 FMI 14 ("Engine Oil Pressure Sensor Plausibility Check Error") on a sibling part: Detroit lists SPN 175 FMI 20 as "Engine Oil Temperature Signal Not Plausible".· Erratic or implausible
    Check soon

    Causes

    • The causes listed under SPN 100 FMI 14, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 100 FMI 14, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 5527 FMI 16OPC Inductor Temperature too High

    Detroit lists SPN 5527 FMI 16 as "OPC Inductor Temperature too High".· Real condition
    Check soon

    Causes

    • A real fault in the system the engine oil pressure sensor measures
    • Sensor reading skewed by a wiring or connector problem

    Checks

    1. 1Confirm the real value with a mechanical gauge or an independent reading before replacing the engine oil pressure sensor.
    2. 2Check the system for the condition the code describes and fix it first.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 521136 FMI 3Oil Pressure Control Circuit Failed High

    Same failure as SPN 100 FMI 3 ("Engine Oil Pressure Sensor Circuit Failed High") on a sibling part: Detroit lists SPN 521136 FMI 3 as "Oil Pressure Control Circuit Failed High".· Shorted high
    Check soon

    Causes

    • The causes listed under SPN 100 FMI 3, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 100 FMI 3, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 521136 FMI 4Oil Pressure Control Circuit Failed Low

    Same failure as SPN 100 FMI 4 ("Engine Oil Pressure Sensor Circuit Failed Low") on a sibling part: Detroit lists SPN 521136 FMI 4 as "Oil Pressure Control Circuit Failed Low".· Shorted low
    Check soon

    Causes

    • The causes listed under SPN 100 FMI 4, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 100 FMI 4, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 521136 FMI 5Oil Pressure Control Circuit Failed Open

    Detroit lists SPN 521136 FMI 5 as "Oil Pressure Control Circuit Failed Open".· Open circuit
    Check soon

    Causes

    • Broken wire or a pushed-out pin in the engine oil pressure sensor connector
    • Corroded terminal or a failed sensor

    Checks

    1. 1Check continuity of every wire between the engine oil pressure sensor connector and the MCM connector.
    2. 2Wiggle the harness and connector while watching the live value for dropouts.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

Shared checks

Checks, in order

  1. 1Check the oil level and condition on the dipstick before anything electrical, and look for fuel or coolant in the oil.
  2. 2Read the live oil pressure in the diagnostic tool at idle and at high idle and compare it with a mechanical gauge at the gallery port.
  3. 3Unplug the oil pressure sensor and inspect the connector for oil, bent pins and green corrosion.
  4. 4Check the sensor supply, return and signal wires back to the MCM for chafing and for continuity.
  5. 5Replace the sensor only after the mechanical gauge proves the pressure is right and the wiring tests good.

Causes

  • Genuinely low oil level or low oil pressure from a worn pump, bearings or a stuck relief valve
  • Oil pressure sensor or its connector damaged by oil, heat or vibration
  • Chafed sensor wiring shorting to ground or to the 5 V supply
  • Wrong oil grade or fuel-diluted oil behind a plausibility code

Most common here: real condition (9 of 23)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: The low-oil-pressure or stop-engine lamp may come on, and the engine may be derated or shut down if the pressure is genuinely low.

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.