Detroit · Controller faults
Detroit CPC5 internal faults and overtemperature pins fault codes
The Common Powertrain Controller (CPC5) handles the vehicle side of the engine controls. These codes cover its memory checksums, clock, internal hardware faults and output pins that overheat or short.
Where to read it
Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.
What do these codes mean?
Detroit codes SPN 629 FMI 12 to SPN 524206 FMI 14 are all about the cPC5 internal faults and overtemperature pins. The most common failure type is part or controller (6 of 15); none needs an immediate stop. Start with this check: read the code detail in the tool and see which pin or area it names.
How urgent are they?
None of the 15 codes here means stop now; all 15 can wait until the shift ends, but find the cause before the next one.
- Check soon15
What should I check first?
Read the code detail in the tool and see which pin or area it names.
Shared checks15 of 15
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Detroit SPN 629 FMI 12Controller #1 Bad Intelligent Device Or Component
Detroit lists SPN 629 FMI 12 as "Controller #1 Bad Intelligent Device Or Component". The CPC5 logged an internal check or configuration fault on the CPC5. Controller number 1 is the device the engine control unit treats as the bad intelligent component in the network.· Part or controllerPart or controllerCheck soonCauses
- Low supply voltage or a bad ground
- Software or data mismatch
Checks
- 1Check the supply and the ground of the CPC5.
- 2Check the software and parameters in the tool.
- 3Read which controller the tool flags as the bad device and check that module power, ground and software.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 630 FMI 2CPC Internal - Checksum Error in Nonvolatile Memory
Detroit lists SPN 630 FMI 2 as "CPC Internal - Checksum Error in Nonvolatile Memory". The CPC5 logged an internal check or configuration fault on the CPC5. The CPC5 checks its own memory with checksums at start-up; a mismatch means stored data is damaged or the software does not match the hardware.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Low supply voltage or a bad ground
- Software or data mismatch
Checks
- 1Check the supply and the ground of the CPC5.
- 2Check the software and parameters in the tool.
- 3Reload the CPC5 software with the tool and see whether the nonvolatile memory checksum clears.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 630 FMI 13CPC Internal - Checksum Error in Production Data Coding Area
Same failure as SPN 630 FMI 2 ("CPC Internal - Checksum Error in Nonvolatile Memory") on a sibling part: Detroit lists SPN 630 FMI 13 as "CPC Internal - Checksum Error in Production Data Coding Area". The CPC5 checks its own memory with checksums at start-up; a mismatch means stored data is damaged or the software does not match the hardware.· Part or controllerPart or controllerCheck soonCauses
- The causes listed under SPN 630 FMI 2, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 630 FMI 2, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 630 FMI 14CPC Internal - Software vs. Hardware Variant Mismatch
Detroit lists SPN 630 FMI 14 as "CPC Internal - Software vs. Hardware Variant Mismatch". The CPC5 logged an internal check or configuration fault on the CPC5. The CPC5 checks its own memory with checksums at start-up; a mismatch means stored data is damaged or the software does not match the hardware.· Part or controllerPart or controllerCheck soonCauses
- Low supply voltage or a bad ground
- Software or data mismatch
Checks
- 1Check the supply and the ground of the CPC5.
- 2Check the software and parameters in the tool.
- 3Check the CPC5 part number against the vehicle build; a hardware variant that does not match the software needs the correct software.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 705 FMI 3Malfunction Indicator Lamp Indicates a Short to Power/open Circuit on Pin 13 of the Common Powertrain Controller #1Connector
Detroit lists SPN 705 FMI 3 as "Malfunction Indicator Lamp Indicates a Short to Power/open Circuit on Pin 13 of the Common Powertrain Controller #1Connector". The CPC5 logged an internal check or configuration fault on the CPC5. The malfunction indicator lamp is driven from a CPC5 output pin; a short or open on that pin stops the lamp from working correctly.· Shorted highShorted highCheck soonCauses
- Low supply voltage or a bad ground
- Software or data mismatch
Checks
- 1Check the supply and the ground of the CPC5.
- 2Check the software and parameters in the tool.
- 3Check the MIL lamp wire on CPC5 pin 13 for a short to power or an open between the cluster and the controller.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 710 FMI 3Digital Output 4 06 Circuit Failed High
Detroit lists SPN 710 FMI 3 as "Digital Output 4 06 Circuit Failed High". The CPC5 logged an internal check or configuration fault on the CPC5. A spare digital output of the CPC5 is monitored for a short; the code names the pin group so you can find the connected load.· Shorted highShorted highCheck soonCauses
- Low supply voltage or a bad ground
- Software or data mismatch
Checks
- 1Check the supply and the ground of the CPC5.
- 2Check the software and parameters in the tool.
- 3Find the load on digital output 4 pin 06 and check its wire for a short to supply.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 710 FMI 4Digital Output 4 06 Circuit Failed Low
Detroit lists SPN 710 FMI 4 as "Digital Output 4 06 Circuit Failed Low". The CPC5 logged an internal check or configuration fault on the CPC5. A spare digital output of the CPC5 is monitored for a short; the code names the pin group so you can find the connected load.· Shorted lowShorted lowCheck soonCauses
- Low supply voltage or a bad ground
- Software or data mismatch
Checks
- 1Check the supply and the ground of the CPC5.
- 2Check the software and parameters in the tool.
- 3Find the load on digital output 4 pin 06 and check its wire for a short to ground.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 961 FMI 2CPC Clock Data Invalid
Detroit lists SPN 961 FMI 2 as "CPC Clock Data Invalid". The CPC5 logged an internal check or configuration fault on the CPC5. The CPC5 keeps a real-time clock for timers and logging; an invalid clock reading can come from a battery interruption.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Low supply voltage or a bad ground
- Software or data mismatch
Checks
- 1Check the supply and the ground of the CPC5.
- 2Check the software and parameters in the tool.
- 3Check the battery connection history, since a power loss can leave the CPC5 clock invalid until the time is set.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 3514 FMI 14CPC5 Overtemp - Pin X3/33
Detroit lists SPN 3514 FMI 14 as "CPC5 Overtemp - Pin X3/33". The CPC5 logged an internal check or configuration fault on the CPC5. This CPC5 pin is monitored for overtemperature, which is typically caused by a shorted load or a damaged wire.· Real conditionReal conditionCheck soonCauses
- Low supply voltage or a bad ground
- Software or data mismatch
Checks
- 1Check the supply and the ground of the CPC5.
- 2Check the software and parameters in the tool.
- 3The CPC5 pin X3/33 is overheated; find the load on this pin and look for a short.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 522222 FMI 2CPC5 Internal EEPROM Checksum Error
Same failure as SPN 630 FMI 2 ("CPC Internal - Checksum Error in Nonvolatile Memory") on a sibling part: Detroit lists SPN 522222 FMI 2 as "CPC5 Internal EEPROM Checksum Error". CPC5 internal EEPROM checksum or data verification error.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 630 FMI 2, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 630 FMI 2, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 522222 FMI 13CPC Internal - EEPROM Data Verification
Detroit lists SPN 522222 FMI 13 as "CPC Internal - EEPROM Data Verification". The CPC5 logged an internal check or configuration fault on the CPC5. CPC5 internal EEPROM checksum or data verification error.· Part or controllerPart or controllerCheck soonCauses
- Low supply voltage or a bad ground
- Software or data mismatch
Checks
- 1Check the supply and the ground of the CPC5.
- 2Check the software and parameters in the tool.
- 3The CPC EEPROM verification failed; reload the data.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 522222 FMI 14CPC5 Internal EEPROM Checksum Error DDEC Reports
Same failure as SPN 630 FMI 2 ("CPC Internal - Checksum Error in Nonvolatile Memory") on a sibling part: Detroit lists SPN 522222 FMI 14 as "CPC5 Internal EEPROM Checksum Error DDEC Reports". CPC5 internal EEPROM checksum or data verification error.· Part or controllerPart or controllerCheck soonCauses
- The causes listed under SPN 630 FMI 2, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 630 FMI 2, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 524200 FMI 14CPC Internal Hardware Defect
Detroit lists SPN 524200 FMI 14 as "CPC Internal Hardware Defect". The CPC5 logged an internal check or configuration fault on the CPC5. CPC internal hardware defect.· OtherOtherCheck soonCauses
- Low supply voltage or a bad ground
- Software or data mismatch
Checks
- 1Check the supply and the ground of the CPC5.
- 2Check the software and parameters in the tool.
- 3A CPC internal hardware defect; replace the CPC5 if the supply is good.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Detroit SPN 524205 FMI 12CPC5 PMC Internal Error
Detroit lists SPN 524205 FMI 12 as "CPC5 PMC Internal Error". The CPC5 logged an internal check or configuration fault on the CPC5. CPC5 PMC internal error.· Part or controllerPart or controllerCheck soonCauses
- Low supply voltage or a bad ground
- Software or data mismatch
Checks
- 1Check the supply and the ground of the CPC5.
- 2Check the software and parameters in the tool.
- 3A CPC5 PMC internal error; reload the software and replace the CPC5 if it persists.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 524206 FMI 14PMC: Double Storage Error
Detroit lists SPN 524206 FMI 14 as "PMC: Double Storage Error". The CPC5 logged an internal check or configuration fault on the CPC5. PMC double storage error.· OtherOtherCheck soonCauses
- Low supply voltage or a bad ground
- Software or data mismatch
Checks
- 1Check the supply and the ground of the CPC5.
- 2Check the software and parameters in the tool.
- 3A PMC double storage error; reload the data in the CPC5.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Read the code detail in the tool and see which pin or area it names.
- 2Check the load and the wiring on the named CPC5 pin.
- 3Reflash the CPC5 software if the tool allows.
- 4Replace the CPC5 only after wiring and software are ruled out.
Causes
- CPC5 internal memory or hardware fault
- Overloaded output pin
- Corrupted software
- Connector damage
Most common here: part or controller (6 of 15)
Check power and ground at the module connector with the key on, then its fuses.
When to stop
You'll notice: The vehicle may lose cruise, throttle response or lamps, and the check-engine lamp comes on.
Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Detroit Diesel DD15 Gen 5 (2023) Fault Codes List, Diesel Repair (SPN/FMI with Detroit descriptions)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
