Detroit · Electrical
Detroit Battery voltage, ignition and starter fault codes
The MCM monitors battery voltage, the ignition circuit and the starter relay. Detroit logs low and high voltage, erratic ignition and starter relay circuit faults.
Where to read it
Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.
What do these codes mean?
Detroit codes SPN 158 FMI 2 to SPN 677 FMI 31 are all about the battery voltage, ignition and starter. The most common failure type is real condition (4 of 9); none needs an immediate stop. Start with this check: test the batteries and the charging voltage with the engine running before touching the wiring.
How urgent are they?
None of the 9 codes here means stop now; all 9 can wait until the shift ends, but find the cause before the next one.
- Check soon9
What should I check first?
Test the batteries and the charging voltage with the engine running before touching the wiring.
Shared checks9 of 9
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Detroit SPN 158 FMI 2Ignition Switch Not Plausible
Detroit lists SPN 158 FMI 2 as "Ignition Switch Not Plausible". The MCM judged the battery and starter circuit reading erratic or not plausible compared with other sensors or its own history. The ignition switch input tells the controller the key position and wakes it up; a bad signal can make the engine run on after key-off or refuse to start.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting battery and starter circuit or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the battery and starter circuit reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 168 FMI 0Battery Voltage High
Detroit lists SPN 168 FMI 0 as "Battery Voltage High". The MCM reports that the measured value itself is out of its normal range; the battery and starter circuit may be correct and a real condition may exist. Battery voltage is read at the controller power pins; a weak battery or a bad charge circuit shows up here and sets many other codes.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the battery and starter circuit measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the battery and starter circuit.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 168 FMI 1Battery Voltage Low
Detroit lists SPN 168 FMI 1 as "Battery Voltage Low". The MCM reports that the measured value itself is out of its normal range; the battery and starter circuit may be correct and a real condition may exist. Battery voltage is read at the controller power pins; a weak battery or a bad charge circuit shows up here and sets many other codes.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the battery and starter circuit measures
- Sensor reading skewed by a wiring or connector problem
Checks
- 1Confirm the real value with a mechanical gauge or an independent reading before replacing the battery and starter circuit.
- 2Check the system for the condition the code describes and fix it first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 168 FMI 2Ignition Circuit Voltage Erratic
Detroit lists SPN 168 FMI 2 as "Ignition Circuit Voltage Erratic". The MCM judged the battery and starter circuit reading erratic or not plausible compared with other sensors or its own history. Battery voltage is read at the controller power pins; a weak battery or a bad charge circuit shows up here and sets many other codes.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting battery and starter circuit or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the battery and starter circuit reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 168 FMI 14Optimized Idle - Charging System or Battery Failure
Detroit lists SPN 168 FMI 14 as "Optimized Idle - Charging System or Battery Failure". The MCM judged the battery and starter circuit reading erratic or not plausible compared with other sensors or its own history. Battery voltage is read at the controller power pins; a weak battery or a bad charge circuit shows up here and sets many other codes.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting battery and starter circuit or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the battery and starter circuit reading with a second reference such as a gauge or another sensor on the engine.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 168 FMI 18Battery Voltage Low
Same failure as SPN 168 FMI 1 ("Battery Voltage Low") on a sibling part: Detroit lists SPN 168 FMI 18 as "Battery Voltage Low". Battery voltage is read at the controller power pins; a weak battery or a bad charge circuit shows up here and sets many other codes.· Real conditionReal conditionCheck soonCauses
- The causes listed under SPN 168 FMI 1, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 168 FMI 1, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 677 FMI 3Engine Starter Relay Shorted to High Source
Detroit lists SPN 677 FMI 3 as "Engine Starter Relay Shorted to High Source". The MCM saw the battery and starter circuit signal above its valid range. That usually means the signal wire is shorted to a supply voltage or is open at the sensor. The starter relay output is switched by the controller; faults here keep the engine from cranking or leave the starter engaged.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to the 5 V supply or open between the battery and starter circuit and the MCM
- The battery and starter circuit has failed inside
Checks
- 1Unplug the battery and starter circuit and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
- 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 677 FMI 5Engine Starter Relay Open Circuit
Detroit lists SPN 677 FMI 5 as "Engine Starter Relay Open Circuit". The MCM detected an open circuit on the battery and starter circuit line, so the signal floats or is missing. The starter relay output is switched by the controller; faults here keep the engine from cranking or leave the starter engaged.· Open circuitOpen circuitCheck soonCauses
- Broken wire or a pushed-out pin in the battery and starter circuit connector
- Corroded terminal or a failed sensor
Checks
- 1Check continuity of every wire between the battery and starter circuit connector and the MCM connector.
- 2Wiggle the harness and connector while watching the live value for dropouts.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Detroit SPN 677 FMI 31Starter Jammed (Tooth to Tooth Jam)
Detroit lists SPN 677 FMI 31 as "Starter Jammed (Tooth to Tooth Jam)". The MCM logged a condition on the battery and starter circuit; the title says what it measured. The starter relay output is switched by the controller; faults here keep the engine from cranking or leave the starter engaged.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the battery and starter circuit watches
- Sensor or wiring fault
Checks
- 1Read the live value and compare it with a reference.
- 2Check the connector and wiring.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Shared checks
Checks, in order
- 1Test the batteries and the charging voltage with the engine running before touching the wiring.
- 2Check the battery cables and engine grounds for tightness and corrosion.
- 3Inspect the ignition and starter relay circuits for loose pins and heat damage.
- 4Check the MCM supply and ground pins for voltage drop under load.
Causes
- Weak or sulphated batteries
- Charging system fault
- Loose or corroded battery or ground connections
- Starter relay or its wiring faulty
Most common here: real condition (4 of 9)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: Hard starting, no crank or a dim dash, and a check-engine lamp.
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Detroit Diesel DD15 Gen 5 (2023) Fault Codes List, Diesel Repair (SPN/FMI with Detroit descriptions)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
