Detroit · Driver inputs
Detroit Accelerator pedal and idle speed fault codes
The accelerator pedal assembly has two position tracks and its own supply and return wires, read by the CPC5 and passed to the MCM. Detroit lists faults of the tracks, the supplies and the returns, and also the idle-position detection and learn faults.
Where to read it
Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.
What do these codes mean?
Detroit codes SPN 91 FMI 2 to SPN 524208 FMI 14 are all about the accelerator pedal and idle speed. The most common failure type is shorted high (6 of 29); none needs an immediate stop. Start with this check: read the two pedal channels in the tool and compare them while moving the pedal slowly from idle to full.
How urgent are they?
None of the 29 codes here means stop now; all 29 can wait until the shift ends, but find the cause before the next one.
- Check soon29
What should I check first?
Read the two pedal channels in the tool and compare them while moving the pedal slowly from idle to full.
Shared checks29 of 29
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Detroit SPN 91 FMI 2Accelerator Pedal Learn Error
Detroit lists SPN 91 FMI 2 as "Accelerator Pedal Learn Error". The CPC5 judged the accelerator pedal reading erratic or not plausible compared with other sensors or its own history. The accelerator pedal carries two position tracks so the controller can cross-check the driver request; a fault on one track often forces idle-only or limp operation.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting accelerator pedal or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the accelerator pedal reading with a second reference such as a gauge or another sensor on the engine.
- 3Redo the pedal learn procedure with the tool after the pedal assembly is replaced or its connector is disturbed.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 91 FMI 3Accelerator Pedal Sensor 1 Signal
Detroit lists SPN 91 FMI 3 as "Accelerator Pedal Sensor 1 Signal". The CPC5 saw the accelerator pedal signal above its valid range. That usually means the signal wire is shorted to a supply voltage or is open at the sensor. The accelerator pedal carries two position tracks so the controller can cross-check the driver request; a fault on one track often forces idle-only or limp operation.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to the 5 V supply or open between the accelerator pedal and the CPC5
- The accelerator pedal has failed inside
Checks
- 1Unplug the accelerator pedal and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
- 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
- 3Read pedal sensor 1 against sensor 2 in the tool; a reading that jumps while the other is smooth points to track 1 of the pedal.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 91 FMI 5Accelerator Pedal Sensor Signal
Detroit lists SPN 91 FMI 5 as "Accelerator Pedal Sensor Signal". The CPC5 detected an open circuit on the accelerator pedal line, so the signal floats or is missing. The accelerator pedal carries two position tracks so the controller can cross-check the driver request; a fault on one track often forces idle-only or limp operation.· Open circuitOpen circuitCheck soonCauses
- Broken wire or a pushed-out pin in the accelerator pedal connector
- Corroded terminal or a failed sensor
Checks
- 1Check continuity of every wire between the accelerator pedal connector and the CPC5 connector.
- 2Wiggle the harness and connector while watching the live value for dropouts.
- 3Check the pedal signal wire for an open circuit by wiggling the pedal connector while watching the track value.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Detroit SPN 91 FMI 72-Channel Accelerator Pedal Idle Not Recognized
Detroit lists SPN 91 FMI 7 as "2-Channel Accelerator Pedal Idle Not Recognized". The CPC5 judged the accelerator pedal reading erratic or not plausible compared with other sensors or its own history. The accelerator pedal carries two position tracks so the controller can cross-check the driver request; a fault on one track often forces idle-only or limp operation.· Part or controllerPart or controllerCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting accelerator pedal or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the accelerator pedal reading with a second reference such as a gauge or another sensor on the engine.
- 3Release the pedal fully and read the idle validation channel; if it does not change, check the pedal release and the idle channel wire.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 91 FMI 82-Channel Accelerator Pedal Signal 1 Missing
Detroit lists SPN 91 FMI 8 as "2-Channel Accelerator Pedal Signal 1 Missing". The CPC5 judged the accelerator pedal reading erratic or not plausible compared with other sensors or its own history. The accelerator pedal carries two position tracks so the controller can cross-check the driver request; a fault on one track often forces idle-only or limp operation.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting accelerator pedal or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the accelerator pedal reading with a second reference such as a gauge or another sensor on the engine.
- 3With sensor 1 missing the controller runs on one track only; check the connector pin for track 1 before replacing the pedal.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 91 FMI 12Accelerator Pedal Sensor Drifted Out of Learned Range
Detroit lists SPN 91 FMI 12 as "Accelerator Pedal Sensor Drifted Out of Learned Range". The CPC5 lost the accelerator pedal signal completely. The accelerator pedal carries two position tracks so the controller can cross-check the driver request; a fault on one track often forces idle-only or limp operation.· Part or controllerPart or controllerCheck soonCauses
- Signal path broken at the connector or the harness
- Failed sensor or module
Checks
- 1Check the connector and the power supply to the accelerator pedal.
- 2Check the signal wire to the CPC5 for an open.
- 3Look for a worn or bent pedal that no longer reaches the learned end positions and redo the learn.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 91 FMI 13Accelerator Pedal Incorrect Parameterization
Detroit lists SPN 91 FMI 13 as "Accelerator Pedal Incorrect Parameterization". The CPC5 found the accelerator pedal value drifted away from what the engine state says it should be. The accelerator pedal carries two position tracks so the controller can cross-check the driver request; a fault on one track often forces idle-only or limp operation.· Part or controllerPart or controllerCheck soonCauses
- Sensor aged, contaminated or out of calibration
- A real fault in the system being measured
Checks
- 1Compare the accelerator pedal reading with a reference gauge or thermometer with the engine off and cold.
- 2Check the system around the accelerator pedal for leaks, restrictions or contamination.
- 3Check that the pedal type configured in the CPC5 parameters matches the pedal that is fitted.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 188 FMI 31Idle Speed is higher than Targeted Idle Speed
Detroit lists SPN 188 FMI 31 as "Idle Speed is higher than Targeted Idle Speed". The CPC5 logged a condition on the accelerator pedal; the title says what it measured. Idle speed is regulated by the controller to a target; a reading well above it often follows a pedal, cruise or optimized idle fault.· Real conditionReal conditionCheck soonCauses
- A real fault in the system the accelerator pedal watches
- Sensor or wiring fault
Checks
- 1Read the live value and compare it with a reference.
- 2Check the connector and wiring.
- 3Check whether cruise, PTO or optimized idle is holding a raised idle speed target before looking for an engine fault.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 558 FMI 7Accelerator Pedal - Idle Position not Recognized
Detroit lists SPN 558 FMI 7 as "Accelerator Pedal - Idle Position not Recognized". The CPC5 judged the accelerator pedal reading erratic or not plausible compared with other sensors or its own history. The idle validation switch or channel tells the controller that the pedal is fully released; if it is not recognised, the engine may hold a raised idle.· Part or controllerPart or controllerCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting accelerator pedal or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the accelerator pedal reading with a second reference such as a gauge or another sensor on the engine.
- 3Compare the idle validation switch reading with the pedal position and check for a switch that does not release.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 2623 FMI 3Accelerator Pedal Sensor Signal
Same failure as SPN 91 FMI 5 ("Accelerator Pedal Sensor Signal") on a sibling part: Detroit lists SPN 2623 FMI 3 as "Accelerator Pedal Sensor Signal". The accelerator pedal signal is read by the CPC5 from the pedal sensor channels and is cross-checked between the two tracks.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 91 FMI 5, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 91 FMI 5, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 2623 FMI 4Accelerator Pedal Sensor Signal
Same failure as SPN 91 FMI 5 ("Accelerator Pedal Sensor Signal") on a sibling part: Detroit lists SPN 2623 FMI 4 as "Accelerator Pedal Sensor Signal". The accelerator pedal signal is read by the CPC5 from the pedal sensor channels and is cross-checked between the two tracks.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 91 FMI 5, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 91 FMI 5, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 2623 FMI 5Accelerator Pedal Sensor Signal
Same failure as SPN 91 FMI 5 ("Accelerator Pedal Sensor Signal") on a sibling part: Detroit lists SPN 2623 FMI 5 as "Accelerator Pedal Sensor Signal". The accelerator pedal signal is read by the CPC5 from the pedal sensor channels and is cross-checked between the two tracks.· Open circuitOpen circuitCheck soonCauses
- The causes listed under SPN 91 FMI 5, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 91 FMI 5, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Detroit SPN 2623 FMI 8Accelerator Pedal Sensor Signal
Same failure as SPN 91 FMI 5 ("Accelerator Pedal Sensor Signal") on a sibling part: Detroit lists SPN 2623 FMI 8 as "Accelerator Pedal Sensor Signal". The accelerator pedal signal is read by the CPC5 from the pedal sensor channels and is cross-checked between the two tracks.· Erratic or implausibleErratic or implausibleCheck soonCauses
- The causes listed under SPN 91 FMI 5, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 91 FMI 5, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 3512 FMI 3Accelerator Pedal Sensor Supply
Detroit lists SPN 3512 FMI 3 as "Accelerator Pedal Sensor Supply". The CPC5 saw the accelerator pedal signal above its valid range. That usually means the signal wire is shorted to a supply voltage or is open at the sensor. The accelerator pedal supply feeds the position sensor tracks and its fault is often shown together with the pedal tracks.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to the 5 V supply or open between the accelerator pedal and the CPC5
- The accelerator pedal has failed inside
Checks
- 1Unplug the accelerator pedal and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
- 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
- 3The pedal supply is shorted high; check the supply wire at the pedal connector for contact with a power wire.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 3512 FMI 4Accelerator Pedal Sensor Supply
Same failure as SPN 3512 FMI 3 ("Accelerator Pedal Sensor Supply") on a sibling part: Detroit lists SPN 3512 FMI 4 as "Accelerator Pedal Sensor Supply". The accelerator pedal supply feeds the position sensor tracks and its fault is often shown together with the pedal tracks.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 3512 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3512 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 3512 FMI 5Accelerator Pedal Sensor Supply
Same failure as SPN 3512 FMI 3 ("Accelerator Pedal Sensor Supply") on a sibling part: Detroit lists SPN 3512 FMI 5 as "Accelerator Pedal Sensor Supply". The accelerator pedal supply feeds the position sensor tracks and its fault is often shown together with the pedal tracks.· Open circuitOpen circuitCheck soonCauses
- The causes listed under SPN 3512 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3512 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Detroit SPN 3512 FMI 14Overtemp - Pin X3_20
Detroit lists SPN 3512 FMI 14 as "Overtemp - Pin X3_20". The CPC5 judged the accelerator pedal reading erratic or not plausible compared with other sensors or its own history. The accelerator pedal supply feeds the position sensor tracks and its fault is often shown together with the pedal tracks.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting accelerator pedal or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the accelerator pedal reading with a second reference such as a gauge or another sensor on the engine.
- 3The CPC5 pin X3/20 is overheated; find the load on this pin and look for a short.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Detroit SPN 3513 FMI 3Accelerator Pedal Sensor Supply
Same failure as SPN 3512 FMI 3 ("Accelerator Pedal Sensor Supply") on a sibling part: Detroit lists SPN 3513 FMI 3 as "Accelerator Pedal Sensor Supply". The second accelerator pedal supply line feeds the pedal tracks; an overtemperature entry points to an overloaded CPC5 pin.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 3512 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3512 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 3513 FMI 14CPC5 Overtemp - Pin X3_7
Same failure as SPN 3512 FMI 14 ("Overtemp - Pin X3_20") on a sibling part: Detroit lists SPN 3513 FMI 14 as "CPC5 Overtemp - Pin X3_7". The second accelerator pedal supply line feeds the pedal tracks; an overtemperature entry points to an overloaded CPC5 pin.· Real conditionReal conditionCheck soonCauses
- The causes listed under SPN 3512 FMI 14, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3512 FMI 14, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 5128 FMI 3Accelerator Pedal Sensor Signal Return
Detroit lists SPN 5128 FMI 3 as "Accelerator Pedal Sensor Signal Return". The CPC5 saw the accelerator pedal signal above its valid range. That usually means the signal wire is shorted to a supply voltage or is open at the sensor. The accelerator pedal sensor signal return is a ground path that the pedal tracks depend on.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to the 5 V supply or open between the accelerator pedal and the CPC5
- The accelerator pedal has failed inside
Checks
- 1Unplug the accelerator pedal and measure the signal pin; a reading near supply with the sensor off means the harness is shorted or open.
- 2Bridge the signal to the return with the sensor unplugged; the reading should fall away if the harness is good.
- 3The pedal signal return is shorted high; check the return wire for a short to supply.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 5128 FMI 4Accelerator Pedal Sensor Signal Return
Same failure as SPN 5128 FMI 3 ("Accelerator Pedal Sensor Signal Return") on a sibling part: Detroit lists SPN 5128 FMI 4 as "Accelerator Pedal Sensor Signal Return". The accelerator pedal sensor signal return is a ground path that the pedal tracks depend on.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 5128 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 5128 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 5128 FMI 5Accelerator Pedal Sensor Signal Return
Same failure as SPN 5128 FMI 3 ("Accelerator Pedal Sensor Signal Return") on a sibling part: Detroit lists SPN 5128 FMI 5 as "Accelerator Pedal Sensor Signal Return". The accelerator pedal sensor signal return is a ground path that the pedal tracks depend on.· Open circuitOpen circuitCheck soonCauses
- The causes listed under SPN 5128 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 5128 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Detroit SPN 5128 FMI 14CPC5 Overtemp - Pin X3_29
Same failure as SPN 3512 FMI 14 ("Overtemp - Pin X3_20") on a sibling part: Detroit lists SPN 5128 FMI 14 as "CPC5 Overtemp - Pin X3_29". The accelerator pedal sensor signal return is a ground path that the pedal tracks depend on.· Real conditionReal conditionCheck soonCauses
- The causes listed under SPN 3512 FMI 14, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3512 FMI 14, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 5129 FMI 3Accelerator Pedal Sensor Signal Return
Same failure as SPN 5128 FMI 3 ("Accelerator Pedal Sensor Signal Return") on a sibling part: Detroit lists SPN 5129 FMI 3 as "Accelerator Pedal Sensor Signal Return". The second accelerator pedal signal return is another ground path for the pedal tracks.· Shorted highShorted highCheck soonCauses
- The causes listed under SPN 5128 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 5128 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Detroit SPN 5129 FMI 4Accelerator Pedal Sensor Signal Return
Same failure as SPN 5128 FMI 3 ("Accelerator Pedal Sensor Signal Return") on a sibling part: Detroit lists SPN 5129 FMI 4 as "Accelerator Pedal Sensor Signal Return". The second accelerator pedal signal return is another ground path for the pedal tracks.· Shorted lowShorted lowCheck soonCauses
- The causes listed under SPN 5128 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 5128 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Detroit SPN 5129 FMI 5Accelerator Pedal Sensor Signal Return
Same failure as SPN 5128 FMI 3 ("Accelerator Pedal Sensor Signal Return") on a sibling part: Detroit lists SPN 5129 FMI 5 as "Accelerator Pedal Sensor Signal Return". The second accelerator pedal signal return is another ground path for the pedal tracks.· Open circuitOpen circuitCheck soonCauses
- The causes listed under SPN 5128 FMI 3, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 5128 FMI 3, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Detroit SPN 5129 FMI 14CPC5 Overtemp - Pin X3_43
Same failure as SPN 3512 FMI 14 ("Overtemp - Pin X3_20") on a sibling part: Detroit lists SPN 5129 FMI 14 as "CPC5 Overtemp - Pin X3_43". The second accelerator pedal signal return is another ground path for the pedal tracks.· Real conditionReal conditionCheck soonCauses
- The causes listed under SPN 3512 FMI 14, found on this part and its own connector and harness leg
- A fault that affects only this channel and not the part that the first code names
Checks
- 1Run the checks listed under SPN 3512 FMI 14, but at this part and on its own wires.
- 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Detroit SPN 524207 FMI 12Accelerator Pedal No Response
Detroit lists SPN 524207 FMI 12 as "Accelerator Pedal No Response". The CPC5 lost the accelerator pedal signal completely. Accelerator pedal no response.· Part or controllerPart or controllerCheck soonCauses
- Signal path broken at the connector or the harness
- Failed sensor or module
Checks
- 1Check the connector and the power supply to the accelerator pedal.
- 2Check the signal wire to the CPC5 for an open.
- 3The accelerator pedal does not respond; check the pedal wiring and the CPC5 input.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Detroit SPN 524208 FMI 14Accelerator Pedal - Idle Position Not Detected
Detroit lists SPN 524208 FMI 14 as "Accelerator Pedal - Idle Position Not Detected". The CPC5 judged the accelerator pedal reading erratic or not plausible compared with other sensors or its own history. Accelerator pedal idle position not detected.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Loose or corroded connector causing a noisy signal
- A drifting accelerator pedal or a related fault in the part it measures
Checks
- 1Watch the live value while wiggling the harness to find an intermittent connection.
- 2Compare the accelerator pedal reading with a second reference such as a gauge or another sensor on the engine.
- 3The pedal idle position was not detected; redo the idle learn.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Shared checks
Checks, in order
- 1Read the two pedal channels in the tool and compare them while moving the pedal slowly from idle to full.
- 2Check the pedal connector for corrosion, bent pins and spread terminals.
- 3Test the supply and return wires between the pedal and the CPC5 for continuity and shorts.
- 4Check that the idle validation and learn procedure completes with the pedal released.
- 5Replace the pedal assembly only after the wiring has tested good.
Causes
- Accelerator pedal assembly worn or out of calibration
- Connector or harness damage at the pedal or at the CPC5 connector
- Supply or return wire short to ground or to supply
- CPC5 pin output overtemperature or a faulty controller
Most common here: shorted high (6 of 29)
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
When to stop
You'll notice: The engine may idle high or only idle, or not respond to the pedal, and the check-engine lamp comes on.
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Detroit Diesel DD15 Gen 5 (2023) Fault Codes List, Diesel Repair (SPN/FMI with Detroit descriptions)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
