Cat · Engine speed
Cat Fault Code CID 190 FMI 08
Engine speed sensor signal abnormal
What does Cat code CID 190 FMI 08 mean?
The ECM lost the primary speed/timing signal, intermittently or fully, for two seconds. The manual lists an open harness, a faulty primary (crank) speed sensor, or the ECM. Urgency: stop now - shut down and fix before working on. Check first: connect Cat ET, try to start the engine and confirm 190-8 is active.
- CID 190
- Which component is at fault
- FMI 08
- Abnormal frequency, pulse width or period
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Connect Cat ET, try to start the engine and confirm 190-8 is active.
Then 4 more checksWhere this code shows
Turn the key on and check the cluster or monitor for a warning lamp.
Checks
0 of 5 done
Causes
- Open in the engine control harness to the crank sensor
- Faulty primary speed (crankshaft) sensor
- Engine ECM
How it failed
You'll notice: The engine may crank but not start, stall suddenly, or run rough, and the tachometer can jump or drop.
Erratic or implausibleRead from FMI 8: abnormal frequency, pulse width or period
The reading jumps, drifts or disagrees with the sensors around it.
- Meter test
- Watch the live value on the service tool while you flex the harness and tap the connector.
- Good result
- A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Engine speed sensors, ECM data and data link
4 other codes on this part are also erratic or implausible (CID 253 FMI 02, CID 268 FMI 02, CID 342 FMI 08, CID 549 FMI 02). When they show together, start at the wiring and connector they share.
- E172High air filter restrictionReal conditionCheck soon
- CID 190 FMI 08Engine speed sensor signal abnormalErratic or implausibleStop now
- E236Return hydraulic oil filter pluggedOtherCheck soon
- CID 247 FMI 09J1939 data link abnormal update rateLost messageCheck soon
- CID 253 FMI 02Personality module incorrectErratic or implausibleCheck soon
- CID 261 FMI 11Engine timing not identifiableOtherCheck soon
- CID 268 FMI 02Engine control module data incorrectErratic or implausibleCheck soon
- E329Transmission filter pluggedReal conditionCheck soon
- CID 342 FMI 08Secondary engine speed sensor signal abnormalErratic or implausibleCheck soon
- E362Engine overspeedReal conditionCheck soon
- CID 549 FMI 02Throttle lock mode switch data erraticErratic or implausibleCheck soon
Related on Equipments Finder
Source
This source lists CID 190 FMI 08 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Cat 924H wheel loader with C6.6 engine (engine ECM), per the 924H field maintenance manual; the same CID-FMI scheme is used on other Cat machines with C-series ECMs.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
