Bobcat · Drive
Bobcat Fault Code M2006
Two-speed primary solenoid short to ground
What does Bobcat code M2006 mean?
The two-speed primary solenoid output is shorted to ground, so the coil will not energise correctly. Urgency: check soon - the machine may derate or limit a function. Check first: with the plug off, test the two-speed solenoid output wire to chassis ground; a reading near zero shows a harness short to ground.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
With the plug off, test the two-speed solenoid output wire to chassis ground; a reading near zero shows a harness short to ground
Then 5 more checksWhere this code shows
On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.
Checks
0 of 6 done
Causes
- Moisture inside the two-speed solenoid connector
- Coil insulation breakdown
- Chafed output wire touching the frame on the drive speed valve at the hydrostatic pumps
- Harness crushed at a bracket or clamp
1 more causeFewer causes
- Speed valve spool slow to move because of dirty oil
How it failed
You'll notice: The two-speed solenoid output reads grounded, which stops the controller driving the coil.
Shorted lowRead from how the source describes the code
The signal sits at or near zero volts - less than a working sensor can send.
- Meter test
- Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
- Good result
- Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Brakes, two-speed and drive speed sensors
8 other codes on this part are also shorted low (37-03, C1032-11, C1033-11, C1034-11 and more). When they show together, start at the wiring and connector they share.
- C1051-12Two speed solenoid short to batteryShorted highCheck soon
- C1051-13Two speed solenoid open circuitOpen circuitCheck soon
- C1051-19Two speed solenoid overcurrentReal conditionCheck soon
- M2005Two-speed primary solenoid short to batteryShorted highCheck soon
- M2006Two-speed primary solenoid short to groundShorted lowCheck soon
- M2007Two-speed primary solenoid open circuitOpen circuitCheck soon
- M2032Two-speed primary overcurrentOtherCheck soon
- M3705Two speed secondary short to batteryShorted highCheck soon
- M3706Two speed secondary short to groundShorted lowCheck soon
Show the other 33 codesHide the other codes
- 20-02Two-speed solenoid error ONOtherCheck soon
- 20-03Two-speed solenoid error OFFOtherCheck soon
- 37-02Two-speed secondary error onShorted highCheck soon
- 37-03Two-speed secondary error offShorted lowCheck soon
- C1030-00Two speed shift not allowedOtherCheck soon
- C1032-11Brake pull output short to groundShorted lowCheck soon
- C1032-12Brake pull output short to batteryShorted highCheck soon
- C1032-13Brake pull output open circuitOpen circuitCheck soon
- C1033-11Left brake hold output short to groundShorted lowCheck soon
- C1033-12Left brake hold output short to batteryShorted highCheck soon
- C1033-13Left brake hold output open circuitOpen circuitCheck soon
- C1034-11Right brake hold output short to groundShorted lowCheck soon
- C1034-12Right brake hold output short to batteryShorted highCheck soon
- C1034-13Right brake hold output open circuitOpen circuitCheck soon
- C1035-16Left brake pull relay error offShorted lowCheck soon
- C1035-17Left brake pull relay error onShorted highCheck soon
- C1036-16Right brake pull relay error offShorted lowCheck soon
- C1036-17Right brake pull relay error onShorted highCheck soon
- C1051-11Two speed solenoid short to groundShorted lowCheck soon
- M3707Two speed secondary open circuitOpen circuitCheck soon
- M3732Two speed secondary overcurrentReal conditionCheck soon
- D7511Drive left speed sensor not connectedOpen circuitCheck soon
- D7512Drive right speed sensor not connectedOpen circuitCheck soon
- D7574Drive right wheel speed uncommanded motionOtherCheck soon
- D7575Drive left wheel speed uncommanded motionOtherCheck soon
- D7577Drive left speed sensor out of range highOtherCheck soon
- D7578Drive right speed sensor out of range highOtherCheck soon
- D7579Drive left speed sensor out of range lowOtherCheck soon
- D7580Drive right speed sensor out of range lowOtherCheck soon
- D7593Drive unresponsive right speed sensorOtherCheck soon
- D7594Drive unresponsive left speed sensorOtherCheck soon
- D7595Drive left speed sensor reverse directionOtherCheck soon
- D7596Drive right speed sensor reverse directionOtherCheck soon
Other Bobcat codes: Drive
Related on Equipments Finder
Source
Bobcat Service Code List (rev. 10-20, M-Series/R-Series loaders and M-Series excavators)
This source lists M2006 and its meaning. The guidance on this page is general, not taken from it.
The source covers: M-Series loaders (S450-S850, T450-T870) and M-Series excavators (E26-E85).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
