EF Logo

Gravel and sand calculator (tons, m³ and truckloads)

How much gravel do I need? Enter the length, width and depth of the area and pick the material to get cubic metres, tons and the number of 20-ton truckloads to order.

The formula

Volume = length × width × depth; tons = volume × density.

What it works out

How much gravel, sand or aggregate an area needs, in m³ and tons.

Why it matters

Order the right amount and the right number of trucks.

How to use it

  1. Under Material, pick gravel, sand, crushed stone, road base, topsoil, fill or asphalt. Each one sets its typical density in t/m³.
  2. Enter the Length and Width of the area in metres.
  3. Enter the Depth in centimetres: the thickness of the layer once it is spread.
  4. Set Extra for Settling (%) for compaction, spreading loss and uneven ground. The default is 10%.
  5. Read Area, Volume, Weight and 20-ton Truckloads. Use Weight and truckloads when you order.

Quick reference

Printable chart

Gravel needed by layer depth (10 m × 4 m, gravel, 10% extra)

Depth (cm)Volume (m³)Weight (t)20-ton loads
52.2 m³3.7 t1 loads
104.4 m³7.39 t1 loads
156.6 m³11.09 t1 loads
208.8 m³14.78 t1 loads
3013.2 m³22.18 t2 loads
4017.6 m³29.57 t2 loads
5022 m³36.96 t2 loads

A 10 m × 4 m area in gravel at 1.68 t/m³ with 10% extra. For another size or material, change the inputs above.

The formula

Area = length × width. Volume = area × depth (in metres) × (1 + extra ÷ 100). Weight in tons = volume × density. Truckloads are the weight divided by 20 tons, rounded up to a whole load.

What changes the result

Density is the big one. The calculator uses typical loose figures: gravel 1.68 t/m³, dry sand 1.6, crushed stone 1.6, road base 2.0, topsoil 1.25, fill 1.5 and asphalt 2.4. Wet sand or a graded road base can be heavier, so ask the supplier for the figure on their ticket. Depth matters as much as area: a few extra centimetres over a large yard adds up to several truckloads. The 10% allowance covers compaction and uneven ground; use less on a flat, well-prepared base.

Ordering on UAE sites

Suppliers in Dubai, Abu Dhabi and Sharjah usually sell sand and aggregate by the ton or by the tipper load, so the weight is the number to quote. A standard tipper carries about 20 to 30 tons, but the legal axle load and the access to your site decide how much can be delivered at once. Order the surface layer separately from the sub-base, since they use different materials and densities.

Worked examples

  • A 10 m × 4 m path with 10 cm of gravel is 40 m². Order 4.4 m³, which weighs 7.39 t: 1 loads of 20 tons.
  • A 25 m × 12 m yard with 15 cm of dry sand needs 49.5 m³, about 79.2 t, or 4 loads of 20 tons.
  • A 200 m × 7 m access road with 20 cm of road base and 5% extra is 294 m³, or 588 t.

Frequently asked questions

How much gravel do I need?

Multiply the length by the width by the depth (all in metres) to get cubic metres, add 5 to 10% for settling, then multiply by the density to get tons. The calculator above does all of this in one step.

How many tons of gravel are in a cubic metre?

Loose gravel is about 1.6 to 1.7 tons per cubic metre. This tool uses 1.68 t/m³ for gravel; check the figure with your supplier.

How do I use a sand calculator?

Choose Sand, dry, enter the area and the depth of the layer, and read the weight in tons. Wet sand weighs more per cubic metre, so ask the supplier if it is delivered damp.

How many truckloads of gravel do I need?

Divide the total weight by the payload of the truck. The calculator shows the number of 20-ton loads; a larger tipper needs fewer trips.

How deep should a gravel layer be?

It depends on the use. A path or drainage layer is often 5 to 10 cm, while a driveway or yard base is commonly 15 to 30 cm or more. Follow the engineer’s specification for roads and slabs.

Add this calculator to your website

Copy the code and paste it into your page. The calculator is free and works as it does here.

<iframe src="https://www.equipmentsfinder.com/embed/field-tools/gravel-sand-calculator" title="Gravel and sand calculator (tons, m³ and truckloads)" width="100%" height="620" style="border:0;max-width:720px" loading="lazy"></iframe>
<p style="font-size:12px"><a href="https://www.equipmentsfinder.com/field-tools/gravel-sand-calculator">Gravel and sand calculator (tons, m³ and truckloads)</a> by <a href="https://www.equipmentsfinder.com">EquipmentsFinder</a></p>
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.