Thermo King · Maintenance reminders (SR-2/SR-3/SR-4)
Thermo King Run-time reminders and hourmeter limits fault codes
This page covers the service reminders: engine, electric and total run-time reminders and the hourmeter limits. The controller counts engine, electric and total run hours and tells the owner when a service is due.
More about these partsLess
Extra hourmeters on the controller can be set to remind the owner of a service.
Where this code shows
Press the alarm key or open the Alarms menu on the controller display to list active alarms.
What do these codes mean?
Thermo King codes 64 to 134 are all about the run-time reminders and hourmeter limits. The most common failure type is real condition (3 of 12); none needs an immediate stop. Start with this check: do the service that is due for the counter shown on the display.
How urgent are they?
None of the 12 codes here means stop now; 1 can wait until the shift ends, but find the cause before the next one; 11 are information only.
- Check soon1
- Info11
What should I check first?
Do the service that is due for the counter shown on the display
Shared checks12 of 12
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Thermo King 64Pretrip reminder
A reminder that a pretrip inspection is due based on the elapsed time since the last pretrip was completed.· OtherOtherInfoCauses
- Pretrip interval has expired
- Pretrip never run since the interval was set
- Hour meter threshold reached
Checks
- 1Run a pretrip test from the controller menu and watch each step through
- 2Clear the alarm after the pretrip completes, so the interval timer restarts
- 3Check the interval setting in the configuration
- 4Record the date of the pretrip in the maintenance log for the unit
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 70Hourmeter failure
The controller found an error in one of its hourmeter counters, so run-time records for service intervals may be wrong.· OtherOtherCheck soonCauses
- Memory fault inside the controller
- Controller reset after power loss
- Failed controller board
Checks
- 1Open the hourmeter display and compare with the unit service records
- 2Clear alarms and watch if the hours count normally
- 3Replace the controller if the meter keeps failing
- 4Re-enter the hour values if the service tool allows
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 71Hourmeter 4 exceeds set time limit
Hourmeter 4 has run past the time limit it was set to. It is a service reminder.· Real conditionReal conditionInfoCauses
- Maintenance interval reached
- Hourmeter not reset after service
Checks
- 1Do the service that hourmeter 4 tracks
- 2Reset the hourmeter after service
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Thermo King 72Hourmeter 5 exceeds set time limit
Hourmeter 5 has run past the time limit it was set to. It is a service reminder.· Real conditionReal conditionInfoCauses
- Maintenance interval reached
- Hourmeter not reset after service
Checks
- 1Do the service that hourmeter 5 tracks
- 2Reset the hourmeter after service
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Thermo King 73Hourmeter 6 exceeds set time limit
Hourmeter 6 has run past the time limit it was set to. It is a service reminder.· Real conditionReal conditionInfoCauses
- Maintenance interval reached
- Hourmeter not reset after service
Checks
- 1Do the service that hourmeter 6 tracks
- 2Reset the hourmeter after service
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Thermo King 128Engine run time maintenance reminder 1 / service due
The engine run time has reached the first maintenance interval, so the unit is due for its engine service.· OtherOtherInfoCauses
- Engine hours reached the service interval
- Hourmeter not reset after the last service
- Interval set shorter than needed
Checks
- 1Do the engine service: oil, filters and belt inspection per the service schedule
- 2Reset the maintenance hourmeter in the menu after the work is complete
- 3Check the interval setting is what the fleet intends and was not changed by mistake
- 4Record the service in the maintenance log with the hours
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 129Engine run time maintenance reminder 2
The second engine run-time service reminder has come due. It tells the owner that the engine hours for the next service have been reached.· OtherOtherInfoCauses
- Service interval reached
- Reminder not reset after the last service
Checks
- 1Do the service listed for reminder 2
- 2Reset the reminder in the maintenance menu
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 130Engine run time maintenance reminder 1
The first engine run-time service reminder has come due. It tells the owner that the engine hours for the next service have been reached.· OtherOtherInfoCauses
- Service interval reached
- Reminder not reset after the last service
Checks
- 1Do the service listed for reminder 1
- 2Reset the reminder in the maintenance menu
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 131Electric run time maintenance reminder 2
The second electric run-time service reminder has come due. It tracks the hours on electric standby rather than the diesel engine.· OtherOtherInfoCauses
- Service interval reached
- Reminder not reset
Checks
- 1Do the electric standby service
- 2Reset the reminder in the maintenance menu
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 132Total unit run time maintenance reminder 1
The first total unit run-time reminder has come due. It counts all running hours, diesel and electric together.· OtherOtherInfoCauses
- Service interval reached
- Reminder not reset
Checks
- 1Do the service for total run time
- 2Reset the reminder in the maintenance menu
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 133Total unit run time maintenance reminder 2
The second total unit run-time reminder has come due. It counts all running hours, diesel and electric together.· OtherOtherInfoCauses
- Service interval reached
- Reminder not reset
Checks
- 1Do the service for total run time
- 2Reset the reminder in the maintenance menu
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 134Controller power on hours
The controller power-on hours have reached a set limit. It is a time-based reminder rather than a fault.· OtherOtherInfoCauses
- Set hours reached
- Reminder not reset
Checks
- 1Do the service linked to the controller hours
- 2Reset the reminder after service
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Do the service that is due for the counter shown on the display
- 2Do the service tracked by the hourmeter that tripped
- 3Reset the reminder in the maintenance menu after the service
- 4Reset the hourmeter after the service is finished
- 5Check the interval settings in the controller
- 6Check the hourmeter limit settings in the controller menu
- 7Record the service in the unit log for the next visit
Causes
- Service interval reached
- Limit reached
- Reminder not reset
- Not reset after service
Most common here: real condition (3 of 12)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: A reminder alarm for the end-of-day report that does not affect running.
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
