JCB · Engine ECU (Dieselmax / Ecomax) - speed sensors
JCB Fault Code P0335
Crankshaft position sensor circuit fault
What does JCB code P0335 mean?
The ECU is not getting a valid crankshaft signal. The engine may not start, may stall or lose torque; on Ecomax a crank overspeed fault can stop the engine. Urgency: stop now - shut down and fix before working on. Check first: look at the live engine speed in the diagnostic tool while cranking and confirm a reading appears.
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Look at the live engine speed in the diagnostic tool while cranking and confirm a reading appears
Then 5 more checksWhere this code shows
Switch the key on and note any warning lamp or fault icon on the cluster.
Checks
0 of 6 done
Causes
- Crankshaft speed sensor failed or its signal weak
- Damaged or loose sensor connector, or a broken wire to the ECU
- Metal debris or oil sludge on the sensor tip
- Sensor air gap changed because it is loose in the housing
1 more causeFewer causes
- Damaged or missing teeth on the crank trigger wheel
How it failed
You'll notice: The engine cranks but may not start, or it stalls, runs with a hunting idle and loses torque.
Lost messageRead from how the source describes the code
A module stopped hearing another on the data link, or the data came late or garbled.
- Meter test
- Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
- Good result
- About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Engine speed and timing sensors, oil pressure and oil level
3 other codes on this part are also lost message (P250B, P0336, P0340). When they show together, start at the wiring and connector they share.
- P0016Crank and cam position correlation faultOtherCheck soon
- P250BEngine oil level low at key-onLost messageCheck soon
- P0325Accelerometer fault (signal to noise ratio too low at idle)Real conditionCheck soon
- P0330Knock sensor 1 circuit faultOtherCheck soon
- P0335Crankshaft position sensor circuit faultLost messageStop now
- P0336Crankshaft sensor signal faultLost messageStop now
- P0340Camshaft position sensor circuit faultLost messageCheck soon
- P0341Camshaft position sensor A range/performanceErratic or implausibleCheck soon
- P0371Excessive pulses on crankshaft sensor signal AOtherCheck soon
Show the other 6 codesHide the other codes
- P0372Too few pulses on crankshaft sensor signal AOtherCheck soon
- P0374No pulses on crankshaft sensor signal AOpen circuitCheck soon
- P0520Low oil pressure warning lamp control circuit faultOtherInformation
- P0521Engine oil pressure sensor or switch range/performanceErratic or implausibleCheck soon
- P0522High oil pressureOtherCheck soon
- P0523Low oil pressureShorted highStop now
Related on Equipments Finder
Source
Partao JCB fault code P0335 page
This source lists P0335 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Dieselmax / Ecomax engines (3CX, 4CX, JS, Loadall).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
