J1939 · Cooling
SPN 110 Fault Code
Engine coolant temperature
What does SPN 110 mean?
Engine coolant temperature, read by a sensor in the thermostat housing or block. The ECM uses it for fan control, idle and cold-start strategy and overtemperature protection. How urgent it is depends on the FMI after SPN 110 - pick it below. Check first: compare the sensor reading with a clean infrared reading on the thermostat housing after a cold soak; they should be within a few degrees.
- SPN 110
- Engine coolant temperature
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 110 - pick it below.
What should I check first?
Compare the sensor reading with a clean infrared reading on the thermostat housing after a cold soak; they should be within a few degrees
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 110?
You'll notice: The temperature gauge reads cold or pegs hot, the radiator fan may run all the time or never, and the ECM can derate or shut the engine down on a false overheat reading.
Find the number shown after SPN 110 on your display. 5 of them have their own page with causes and checks.
- 0SPN 110 FMI 0: Value is above the normal range, most severe levelReal conditionCummins ISX15, Detroit DD15, Detroit DD13, Detroit DD13 Gen 5 and 4 more
- 2SPN 110 FMI 2: Data is erratic, intermittent or incorrectErratic or implausibleCummins ISX15, Detroit DD15, Mack MP8, Mack MP7 and 2 more
- 3SPN 110 FMI 3: Signal voltage is above normal, or the circuit is shorted to a high sourceShorted highCummins ISX15, Detroit DD15, Detroit DD13, PACCAR MX-13
- 4SPN 110 FMI 4: Signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowCummins ISX15, Detroit DD15, Detroit DD13, Detroit DD13 Gen 5 and 5 more
- 5SPN 110 FMI 5: Current is below normal, or the circuit is openOpen circuitMack MP8, Mack MP7, Volvo D13
- 9SPN 110 FMI 9: The coolant temperature message did not arrive over CANLost messageDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 10SPN 110 FMI 10: The value is changing at an abnormal rateErratic or implausibleMack MP8, Mack MP7, Volvo D13
- 12SPN 110 FMI 12: Coolant temperature data is unlikely or erratic, so the reading is not trustedPart or controllerPACCAR MX-13
- 13SPN 110 FMI 13: The value is out of calibrationPart or controllerMack MP8, Mack MP7, Volvo D13
- 14SPN 110 FMI 14: Coolant temperature disagrees with oil temperature, so the reading fails a plausibility checkErratic or implausibleDetroit DD15
- 15SPN 110 FMI 15: Value is above the normal range, least severe levelReal conditionCummins ISX15
- 16SPN 110 FMI 16: Value is above the normal range, moderately severe levelReal conditionCummins ISX15, Mack MP8, Mack MP7, PACCAR MX-13 and 1 more
- 17SPN 110 FMI 17: Value is below the normal range, least severe levelReal conditionMack MP8, Mack MP7, Volvo D13
- 18SPN 110 FMI 18: Value is below the normal range, moderately severe levelReal conditionCummins ISX15
- 20SPN 110 FMI 20: Coolant outlet temperature sensor failed the general plausibility checkErratic or implausibleDetroit DD13 Gen 5, Detroit DD15 Gen 5
- 31SPN 110 FMI 31: A condition exists: the ECM is flagging a defined state rather than a circuit failureReal conditionCummins ISX15
Checks
0 of 5 done
When to stop
Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.
How urgent SPN 110 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Reads cold: an open circuit or a short to supply in the coolant temperature sensor wiring, which the ECM reads as an extremely low temperature
- Reads hot: signal wire shorted to ground or the coolant temperature sensor element shorted, which the ECM reads as an extremely high temperature
- Real condition: low coolant or a stuck thermostat giving a real temperature that is too high or too low
- Real condition: fan clutch, fan drive or radiator airflow problem allowing real overheating
1 more causeFewer causes
- Sensor: air pocket or low coolant leaving the sensor tip dry, so the reading jumps as coolant sloshes
Other Cooling codes
Source
Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)
This list names SPN 110 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
