Genie · Switch and joystick faults at startup (U)
Genie Ground and platform control switches fault codes
At power-up the ECM reads every switch on both control stations and flags any that is already closed. The ground controls (GCON) carry a main function enable switch, up and down directional switches, a deck enable switch and four LCD menu keys.
More about these partsLess
The platform controls carry drive enable, steer, horn and speed switches, a drive mode switch, lift speed, up, down, function enable and lift mode switches and, on the GS-3232, outrigger switches. One code also catches the ground and platform key positions both being selected.
Where this code shows
Scissors: read the code on the platform LED display or the ground control LCD.
What do these codes mean?
Genie codes U001 to U046 are all about the ground and platform control switches. The most common failure type is real condition (7 of 23); 1 needs an immediate stop. Start with this check: release every switch at the station named by the code, cycle the key and see whether the code returns; a code on a free switch points at the switch or its wire.
How urgent are they?
1 of 23 codes here means stop now; the other 22 can wait until the shift ends, but find the cause before the next one.
- Stop now1
- Check soon22
What should I check first?
Release every switch at the station named by the code, cycle the key and see whether the code returns; a code on a free switch points at the switch or its wire.
Shared checks23 of 23
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Genie U001GCON main function enable switch shorted at startup
The GCON main function enable switch was closed at start-up. All GCON functions are inhibited.· OtherOtherCheck soonCauses
- Enable toggle on the ground box was held over or jammed when the key was turned on
- Enable switch contacts burned together after an earlier short
Checks
- 1Cycle the key with your hands clear of the ground box; if U001 stays, work the enable toggle both ways and meter it, because this one switch gates every ground function.
- 2Unplug the enable switch wires; reading closed with no wires on means replace the switch, reading open means look for a shorted wire inside the ground box.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie U002GCON up directional switch shorted at startup
The GCON up directional switch was closed at start-up. All GCON functions are inhibited except platform down.· OtherOtherCheck soonCauses
- Up contact of the ground up/down toggle stuck closed
- Up signal wire pinched against the supply feed inside the ground box
Checks
- 1Cycle the key with the toggle centred; platform down should still work, which confirms the up side is the closed one.
- 2Meter the up contact of the toggle: open at rest, closed only while pushed up.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie U003GCON down directional switch shorted at startup
The GCON down directional switch was closed at start-up. All GCON functions are inhibited except platform up.· OtherOtherCheck soonCauses
- Down contact of the ground up/down toggle stuck closed
- Down signal wire pinched against the supply feed inside the ground box
Checks
- 1Cycle the key with the toggle centred; platform up should still work, which confirms the down side is the closed one.
- 2Meter the down contact of the toggle: open at rest, closed only while pushed down, and compare it with the up contact of the same toggle.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie U004GCON LCD scroll up switch shorted at startup
The GCON LCD scroll up switch was closed at start-up. All GCON LCD menu functions are inhibited.· OtherOtherCheck soonCauses
- Scroll up key under the ground LCD jammed by dirt or a swollen rubber boot
- Scroll up key held down by the lid or a stray object inside the ground box
Checks
- 1Press and release the scroll up key a few times and listen for it clicking back; a mushy key is stuck closed.
- 2Scroll the menu with the other three LCD keys; if only scroll up is dead, the code is the key and not the display.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie U005GCON LCD scroll down switch shorted at startup
The GCON LCD scroll down switch was closed at start-up. All GCON LCD menu functions are inhibited.· OtherOtherCheck soonCauses
- Scroll down key under the ground LCD jammed or corroded
- Scroll down key contacts shorted by water in the ground box
Checks
- 1Press scroll down repeatedly and check it springs back each time; a key that stays down also freezes menu movement.
- 2Meter the scroll down key contacts with the wires off; closed at rest means replace the key.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie U006GCON LCD enter switch shorted at startup
The GCON LCD enter switch was closed at start-up. All GCON LCD menu functions are inhibited.· OtherOtherCheck soonCauses
- Enter key on the ground LCD held in when power was applied
- Enter key contacts welded by corrosion
Checks
- 1Release the enter key, cycle the key switch and note whether the menu opens by itself; if it does, the enter contact is closed.
- 2Meter the enter key contacts at rest and while pressed; a reading that never opens means replace the key.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie U007GCON LCD escape switch shorted at startup
The GCON LCD escape switch was closed at start-up. All GCON LCD menu functions are inhibited.· OtherOtherCheck soonCauses
- Escape key on the ground LCD jammed or held in at power-up
- Escape key wire shorted in the ground box harness
Checks
- 1Press escape once and watch the menu back out; a key that does not release leaves the LCD locked on the last screen.
- 2Open the ground box and trace the escape wire for a pinched strand before replacing the key.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie U014PCON drive enable switch shorted at startup
The PCON drive enable switch was closed at start-up. All PCON drive and steer functions are inhibited.· OtherOtherCheck soonCauses
- Drive enable switch held in by the operator or taped down at power-up
- Drive enable contacts failed closed
Checks
- 1Cycle the key with the drive enable released; drive and steer should come back only if the switch was being held.
- 2Meter the drive enable switch at rest in the platform box; it must be open, and a closed reading with its wires removed means the switch has failed.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie U015PCON steer left switch shorted at startup
The PCON steer left switch was closed at start-up. All PCON drive and steer functions are inhibited.· OtherOtherCheck soonCauses
- Steer left contact of the platform steer switch stuck closed
- Steer left wire rubbed to supply in the platform cable
Checks
- 1Cycle the key with the steer switch centred and compare the left and right contacts; only one side should ever close.
- 2Check the steer left wire between the switch and the platform box board for a pinched or rubbed spot.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie U016PCON steer right switch shorted at startup
The PCON steer right switch was closed at start-up. All PCON drive and steer functions are inhibited.· OtherOtherCheck soonCauses
- Steer right contact of the platform steer switch stuck closed
- Steer right wire rubbed to supply in the platform cable
Checks
- 1Cycle the key with the steer switch centred and compare the right and left contacts of the same switch.
- 2Check the steer right wire between the switch and the platform box board for a pinched or rubbed spot.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie U017PCON horn switch shorted at startup
The PCON horn switch was closed at start-up. The PCON horn switch function is inhibited.· OtherOtherCheck soonCauses
- Horn button held down by something resting on the platform controls
- Horn switch contacts shorted by water or corrosion
Checks
- 1Look for an object wedged against the horn button, then press and release it and listen for the click back.
- 2Meter the horn switch at rest; it must be open. This code does not stop the machine, so the horn is the only function lost.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie U018PCON low drive speed switch shorted at startup
The PCON low drive speed switch was closed at start-up. The machine is limited to low drive speed.· OtherOtherCheck soonCauses
- Low drive speed switch stuck in the low position when the key was turned on
- Speed selector contacts welded or shorted in the platform box
Checks
- 1Move the drive speed selector to each position and cycle the key; if the machine stays limited to low speed, the low contact is closed.
- 2Meter the low drive speed contact in each selector position; it should close only in the low position.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie U019PCON low lift speed switch shorted at startup
The PCON low lift speed switch was closed at start-up. PCON platform up and down functions are inhibited.· OtherOtherCheck soonCauses
- Low lift speed switch stuck closed at power-up
- Lift speed selector contacts shorted by moisture
Checks
- 1Cycle the key with the lift speed selector in high; platform up and down from the platform stay blocked while the low contact is closed.
- 2Meter the low lift speed contact in each selector position and compare it with the high lift speed contact.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie U020PCON high lift speed switch shorted at startup
The high lift speed switch on the platform controls was closed when the machine powered up. Platform up and down from the platform are blocked until it is released and power is cycled.· Real conditionReal conditionCheck soonCauses
- PCON high lift speed switch stuck closed or held in at start-up
- Switch contacts burned together or contaminated by moisture
- Wire between the switch and the platform box circuit board shorted
Checks
- 1Release the high lift speed switch, cycle the key and see whether the code returns; a code on a free switch points at the switch.
- 2Meter the switch contacts: they should be open when released and close only when pressed.
- 3Open the platform control box and check the switch wiring for a loose strand touching its neighbour.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Genie U021PCON up switch shorted at startup
The platform up direction was active at power-up. Platform up from the platform is blocked until the lift toggle is released and power is cycled.· Real conditionReal conditionCheck soonCauses
- Platform up toggle stuck or held up at start-up
- Lift toggle contacts failed closed
- Short between the up signal wire and the supply in the platform control cable
Checks
- 1Release the platform lift toggle and cycle the key; if the code stays, the switch or its wires are closed on their own.
- 2Meter the up contact of the lift switch: it should be open at rest and close when the toggle moves up.
- 3Compare the up and down contacts of the same toggle; only one should close at a time.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Genie U022PCON down switch shorted at startup
The platform down direction was active at power-up. Platform down from the platform is blocked until the lift toggle is released and power is cycled.· Real conditionReal conditionCheck soonCauses
- Platform down toggle stuck or held down at start-up
- Lift toggle down contact welded or contaminated
- Platform cable shorted between the down signal wire and supply
Checks
- 1Release the toggle fully and cycle the key; if the code returns, the down contact is closed by itself.
- 2Meter the down contact of the lift switch; it should be open at rest.
- 3Use the ground controls to lower the platform if it was raised when the code set, then test the platform controls again.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Genie U023PCON outrigger enable switch shorted at startup
The PCON outrigger enable switch was closed at start-up. All outrigger functions are inhibited.· OtherOtherCheck soonCauses
- Outrigger enable switch stuck closed on the platform controls
- Outrigger enable wire shorted to supply in the platform cable
Checks
- 1Cycle the key with the outrigger enable released; outrigger functions return only if it was being held.
- 2Meter the outrigger enable contacts at rest; closed with the wires off means replace the switch. This switch exists only on machines with outriggers.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie U036GCON and PCON key switch wiring fault
The ECM sees the ground and platform key positions selected at the same time. All functions are blocked until the key switch circuit is corrected.· Real conditionReal conditionStop nowCauses
- Key switch wired wrongly or contacts shorted so ground and platform are on together
- Key switch contacts failed
- Harness short between the ground and platform select wires
- GCON select input damaged
Checks
- 1Turn the key to each position and meter the key switch contacts; only one of ground or platform should close.
- 2Disconnect the key switch and check whether the code clears.
- 3Check the select wires between the key switch and the GCON for a short to each other.
- 4Inspect the key switch connector and the wiring behind it for water.
- 5Replace the key switch if both contacts close at once.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Genie U041GCON deck enable switch stuck
The ground control deck-enable switch is stuck closed or was held at start-up. All functions are blocked until it is released and power is cycled.· Real conditionReal conditionCheck soonCauses
- GCON deck enable switch stuck closed
- Switch held down while the key was turned on
- Wire from the switch shorted to supply
Checks
- 1Release the deck enable switch and cycle the key; if the code stays, the switch is stuck.
- 2Meter the switch at rest; it should read open.
- 3Check the switch moves freely at the ground control box and is not seized by corrosion.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Genie U042PCON drive mode switch stuck
The platform drive mode switch is stuck or was held when the machine started. Drive functions are blocked until it is released and power is cycled.· Real conditionReal conditionCheck soonCauses
- Drive mode switch stuck closed
- Switch pressed while power was applied
- Wire from the switch pinched against ground or supply in the platform box
Checks
- 1Release the drive mode switch, cycle the key and see whether the code returns.
- 2Meter the switch in the released position; open is correct.
- 3Check for water or corrosion inside the platform control box.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Genie U043PCON outrigger mode switch stuck at startup
The PCON outrigger mode switch was stuck closed or pressed at start-up. Outrigger extend and retract functions are inhibited.· OtherOtherCheck soonCauses
- Outrigger mode switch stuck in an extend or retract position at power-up
- Outrigger mode switch contacts bridged by moisture
Checks
- 1Return the outrigger mode switch to its centre position and cycle the key; extend and retract only come back if the switch was off centre.
- 2Meter each side of the outrigger mode switch; both sides must be open at rest.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie U045PCON function enable switch stuck
The function enable switch on the platform controls is stuck or was held at start-up. Drive and steer are blocked until it is released and power is cycled.· Real conditionReal conditionCheck soonCauses
- Function enable switch stuck closed or jammed
- Switch held in when the key was turned on
- Corrosion inside the platform control box
Checks
- 1Release the function enable switch fully and cycle the key.
- 2Meter the switch contacts; they should be open at rest and close only while pressed.
- 3Open the platform box and look for water, green corrosion or a stuck rubber boot.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Genie U046PCON lift mode switch stuck
The lift mode switch is stuck or was held at start-up. Everything works except platform up and down until it is released and power is cycled.· OtherOtherCheck soonCauses
- Lift mode switch stuck closed or jammed
- Switch pressed at power-up
- Moisture in the platform box bridging the switch contacts
Checks
- 1Release the lift mode switch and cycle the key; check whether the code returns.
- 2Meter the lift mode switch at rest; the contacts must be open.
- 3Inspect the platform control box for water and corrosion.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Release every switch at the station named by the code, cycle the key and see whether the code returns; a code on a free switch points at the switch or its wire.
- 2Meter the contacts of the named switch with its wires off: open when released, closed only while pressed.
- 3Open the ground or platform box and look for water, green corrosion and loose wire strands touching a neighbour.
- 4Replace the switch if it reads closed with its wires removed.
- 5If the platform was raised when the code set, lower it from the ground controls before testing the platform switches.
Causes
- Switch held in or stuck closed at power-up
- Switch contacts burned together or bridged by water
- Wire between the switch and the control box board shorted to supply
- ECM input damaged (rare)
Most common here: real condition (7 of 23)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: The function behind the stuck switch is limited or blocked until the switch is freed and the key is cycled: a ground control function or the LCD menu for a ground code, or drive, steer, lift or outrigger from the platform for a platform code.
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
