Genie · Controls and ECM faults (C)
Genie Fault Code C025
Platform overload not calibrated
What does Genie code C025 mean?
The platform overload system has no calibration, so all functions are blocked until the overload calibration is performed. It usually follows an ECM or transducer replacement. Urgency: stop now - shut down and fix before working on. Check first: run the platform overload calibration with the platform empty and stowed, then with the test weight as the procedure requires.
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Run the platform overload calibration with the platform empty and stowed, then with the test weight as the procedure requires.
Then 3 more checksWhere this code shows
Scissors: read the code on the platform LED display or the ground control LCD.
Checks
0 of 4 done
Causes
- New or reset ECM
- New overload pressure transducer
- Calibration lost after a software update
- Transducer connector or wiring fault
How it failed
You'll notice: Every function is blocked until the platform overload system is calibrated.
Part or controllerRead from how the source describes the code
The controller reports a part, module or its software as faulty or not responding.
- Meter test
- Check power and ground at the module connector with the key on, then its fuses.
- Good result
- Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Controllers, link, calibration and ECM self-checks
4 other codes on this part are also part or controller (C001, C009, C029, C053). When they show together, start at the wiring and connector they share.
- C009GCON ECM fault type 9Part or controllerStop now
- C010Secondary processor not programmedReal conditionStop now
- C021PCON not detectedLost messageStop now
- C023Machine model faultReal conditionStop now
- C025Platform overload not calibratedPart or controllerStop now
- C028Service override mode onOtherCheck soon
- C029Outrigger sensor not calibratedPart or controllerCheck soon
- C053PCON-GCON software mismatchPart or controllerStop now
- C055Drive controller hardware failure (DCON type 01)Real conditionStop now
Show the other 15 codesHide the other codes
- C001GCON ECM CRC errorPart or controllerStop now
- C004GCON master switch errorReal conditionStop now
- C005GCON safety switch errorReal conditionStop now
- C006GCON input redundancy errorReal conditionStop now
- C007GCON inter-processor communication errorLost messageStop now
- C056Drive controller setup failure (DCON type 02)Real conditionStop now
- C058Drive controller voltage out of range (DCON type 04)Real conditionStop now
- C059Drive controller capacitor charge failure (DCON type 05)Real conditionStop now
- C061Drive controller key switch or B+/B- open (DCON type 07)Real conditionStop now
- C063Drive controller CAN fault (DCON type 09)Lost messageStop now
- C064Drive controller thermal sensor (DCON type 10)Real conditionStop now
- H067Motor controller enable: short to battery negativeShorted highStop now
- H069Motor controller enable: short to battery positiveShorted highStop now
- H070Motor controller throttle: short to battery negativeShorted highStop now
- H072Motor controller throttle: short to battery positiveShorted highStop now
Other Genie codes: Controls and ECM faults (C)
Related on Equipments Finder
Source
This source lists C025 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Genie GS-1530/1532/1930/1932/2032/2632 slab scissors with SmartLink (GSDS) controls.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
