Develon · Communication
Develon Fault Code V201
Gauge panel communication error (V201)
What does Develon code V201 mean?
Short-format code: the gauge panel is not talking to the machine controller. Urgency: check soon - the machine may derate or limit a function. Check first: measure resistance between CN7 pins 4 and 5 with the CAN line connected; the manual gives 60 ohm plus or minus 5.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Measure resistance between CN7 pins 4 and 5 with the CAN line connected; the manual gives 60 ohm plus or minus 5.
Then 3 more checksWhere this code shows
Switch the key on and open the monitor fault or service menu on the gauge panel to see active codes.
Checks
0 of 4 done
Causes
- Open or shorted CAN wire between panel and controller
- Loose or corroded CN7 connector
- CAN termination missing at one end
- Failed gauge panel
How it failed
You'll notice: Short-format V201 from the DX225LCA table; the older DX-3 tables write the same fault as V000201.
Lost messageRead from how the source describes the code
A module stopped hearing another on the data link, or the data came late or garbled.
- Meter test
- Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
- Good result
- About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Monitor, controller and CAN communication
12 other codes on this part are also lost message (V000201, V202, E000639, E001482 and more). When they show together, start at the wiring and connector they share.
- V002ECU CommunicationOtherCheck soon
- V003TCU CommunicationOtherCheck soon
- V004Electric Steering CommunicationOtherCheck soon
- V000201Gauge panel errorLost messageCheck soon
- V201Gauge panel communication error (V201)Lost messageCheck soon
- V000202E-ECU errorOtherCheck soon
- V202ECU communication error (V202)Lost messageCheck soon
- E000639CAN communication errorLost messageCheck soon
- E001482Timeout error of CAN receive frame TCULost messageCheck soon
Show the other 9 codesHide the other codes
- V001Gauge Panel CommunicationOtherCheck soon
- E010040ISO-CAN Bus FaultLost messageCheck soon
- E520197Timeout error of CAN Module CLost messageCheck soon
- E520206Timeout error of CAN Module ALost messageCheck soon
- E520602Hydraulic oil temperature CAN time outLost messageCheck soon
- E520603Timeout error of CAN receive frame DEC1VLost messageCheck soon
- E520606Timeout error of CAN receive frame EGR ValveLost messageCheck soon
- E520611Timeout error of CAN receive frame Vehicle cut off switchLost messageCheck soon
- E520614Timeout error of CAN receive frame VGTLost messageCheck soon
Related on Equipments Finder
Source
Doosan DX225LCA Excavator Fault Codes List - FMI & V-Codes (TruckManualsHub)
This source lists V201 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Doosan / Develon DX excavators and DL wheel loaders, per the table cited.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
