EF Logo

Develon · Communication

Develon Monitor, controller and CAN communication fault codes

Communication faults between the gauge panel (monitor), the machine controller (ECU), the engine controller, the transmission module and the actuators on the CAN bus. Each entry names the module whose messages stopped arriving.

FaultCheckV000201Develon · Monitor, controller and CAN communication
Code shows hereFAULTV000201

Where this code shows

Switch the key on and open the monitor fault or service menu on the gauge panel to see active codes.

What do these codes mean?

Develon codes V001 to E520614 are all about the monitor, controller and CAN communication. Most are lost message faults; none needs an immediate stop. Start with this check: measure resistance across the CAN pair with power off and compare with the manual value.

How urgent are they?

None of the 18 codes here means stop now; all 18 can wait until the shift ends, but find the cause before the next one.

  • Check soon18

What should I check first?

Measure resistance across the CAN pair with power off and compare with the manual value.

Shared checks

18 of 18

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Develon V001Gauge Panel Communication

    Same failure as V000201 on the gauge panel communication, a different part of the same kind as the gauge panel error.· Other
    Check soon

    Causes

    • Fault in the gauge panel communication or its wiring
    • Any cause listed under V000201

    Checks

    1. 1Check the gauge panel communication connector and wiring first, then follow the checks listed under V000201.
    2. 2Clear the code and confirm whether V001 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V002ECU Communication

    Same failure as V000201 on the ecu communication, a different part of the same kind as the gauge panel error.· Other
    Check soon

    Causes

    • Fault in the ecu communication or its wiring
    • Any cause listed under V000201

    Checks

    1. 1Check the ecu communication connector and wiring first, then follow the checks listed under V000201.
    2. 2Clear the code and confirm whether V002 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V003TCU Communication

    Same failure as V000201 on the tcu communication, a different part of the same kind as the gauge panel error.· Other
    Check soon

    Causes

    • Fault in the tcu communication or its wiring
    • Any cause listed under V000201

    Checks

    1. 1Check the tcu communication connector and wiring first, then follow the checks listed under V000201.
    2. 2Clear the code and confirm whether V003 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V004Electric Steering Communication

    Same failure as V000201 on the electric steering communication, a different part of the same kind as the gauge panel error.· Other
    Check soon

    Causes

    • Fault in the electric steering communication or its wiring
    • Any cause listed under V000201

    Checks

    1. 1Check the electric steering communication connector and wiring first, then follow the checks listed under V000201.
    2. 2Clear the code and confirm whether V004 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V000201Gauge panel error

    The machine controller reports that the gauge panel (the monitor in the cab) is not communicating or is faulty.· Lost message
    Check soon

    Causes

    • Damaged or loose gauge panel connector
    • CAN wiring open or shorted between panel and controller
    • Low supply voltage to the panel
    • Failed gauge panel

    Checks

    1. 1Check the gauge panel connector and its supply and ground with the key on, looking for a loose or corroded pin.
    2. 2Measure the resistance across the CAN pair with power off and compare with the manual value for your model.
    3. 3Inspect the harness behind the panel and where it passes the cab floor for rub damage.
    4. 4Swap in a known-good panel, if one is available, to see whether the error follows the panel.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Develon V201Gauge panel communication error (V201)

    Short-format code: the gauge panel is not talking to the machine controller.· Lost message
    Check soon

    Causes

    • Open or shorted CAN wire between panel and controller
    • Loose or corroded CN7 connector
    • CAN termination missing at one end
    • Failed gauge panel

    Checks

    1. 1Measure resistance between CN7 pins 4 and 5 with the CAN line connected; the manual gives 60 ohm plus or minus 5.
    2. 2A reading near 120 ohm suggests one terminating resistor or one branch is missing; near 0 suggests a short between the two wires.
    3. 3Inspect connector CN7 for moisture and pushed-back pins and reseat it.
    4. 4Check the supply and ground at the gauge panel with the key on.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Develon V000202E-ECU error

    Same failure as V000201 on the e-ecu error, a different part of the same kind as the gauge panel error.· Other
    Check soon

    Causes

    • Fault in the e-ecu error or its wiring
    • Any cause listed under V000201

    Checks

    1. 1Check the e-ecu error connector and wiring first, then follow the checks listed under V000201.
    2. 2Clear the code and confirm whether V000202 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V202ECU communication error (V202)

    Same failure as V000201 on the ecu communication error (v202), a different part of the same kind as the gauge panel error.· Lost message
    Check soon

    Causes

    • Fault in the ecu communication error (v202) or its wiring
    • Any cause listed under V000201

    Checks

    1. 1Check the ecu communication error (v202) connector and wiring first, then follow the checks listed under V000201.
    2. 2Clear the code and confirm whether V202 returns on its own.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Develon E000639CAN communication error

    A CAN bus fault means messages between the engine controller and other modules are not being received correctly.· Lost message
    Check soon

    Causes

    • Damaged CAN wires or poor connectors
    • Missing CAN termination
    • A module off the bus or without power
    • Short between the CAN pair or to ground

    Checks

    1. 1Measure resistance across the CAN pair with power off and compare with the manual value.
    2. 2Check power and ground at the module that is not answering.
    3. 3Inspect the bus connectors for water and pushed-back pins.
    4. 4Wiggle the harness while watching the data link for dropouts.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Develon E001482Timeout error of CAN receive frame TCU

    Same failure as E000639 on the timeout error of can receive frame tcu, a different part of the same kind as the can communication error.· Lost message
    Check soon

    Causes

    • Fault in the timeout error of can receive frame tcu or its wiring
    • Any cause listed under E000639

    Checks

    1. 1Check the timeout error of can receive frame tcu connector and wiring first, then follow the checks listed under E000639.
    2. 2Clear the code and confirm whether E001482 returns on its own.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Develon E010040ISO-CAN Bus Fault

    Same failure as E000639 on the iso-can bus fault, a different part of the same kind as the can communication error.· Lost message
    Check soon

    Causes

    • Fault in the iso-can bus fault or its wiring
    • Any cause listed under E000639

    Checks

    1. 1Check the iso-can bus fault connector and wiring first, then follow the checks listed under E000639.
    2. 2Clear the code and confirm whether E010040 returns on its own.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Develon E520197Timeout error of CAN Module C

    Same failure as E000639 on the timeout error of can module c, a different part of the same kind as the can communication error.· Lost message
    Check soon

    Causes

    • Fault in the timeout error of can module c or its wiring
    • Any cause listed under E000639

    Checks

    1. 1Check the timeout error of can module c connector and wiring first, then follow the checks listed under E000639.
    2. 2Clear the code and confirm whether E520197 returns on its own.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Develon E520206Timeout error of CAN Module A

    Same failure as E000639 on the timeout error of can module a, a different part of the same kind as the can communication error.· Lost message
    Check soon

    Causes

    • Fault in the timeout error of can module a or its wiring
    • Any cause listed under E000639

    Checks

    1. 1Check the timeout error of can module a connector and wiring first, then follow the checks listed under E000639.
    2. 2Clear the code and confirm whether E520206 returns on its own.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Develon E520602Hydraulic oil temperature CAN time out

    Same failure as E000639 on the hydraulic oil temperature can time out, a different part of the same kind as the can communication error.· Lost message
    Check soon

    Causes

    • Fault in the hydraulic oil temperature can time out or its wiring
    • Any cause listed under E000639

    Checks

    1. 1Check the hydraulic oil temperature can time out connector and wiring first, then follow the checks listed under E000639.
    2. 2Clear the code and confirm whether E520602 returns on its own.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Develon E520603Timeout error of CAN receive frame DEC1V

    Same failure as E000639 on the timeout error of can receive frame dec1v, a different part of the same kind as the can communication error.· Lost message
    Check soon

    Causes

    • Fault in the timeout error of can receive frame dec1v or its wiring
    • Any cause listed under E000639

    Checks

    1. 1Check the timeout error of can receive frame dec1v connector and wiring first, then follow the checks listed under E000639.
    2. 2Clear the code and confirm whether E520603 returns on its own.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Develon E520606Timeout error of CAN receive frame EGR Valve

    Same failure as E000639 on the timeout error of can receive frame egr valve, a different part of the same kind as the can communication error.· Lost message
    Check soon

    Causes

    • Fault in the timeout error of can receive frame egr valve or its wiring
    • Any cause listed under E000639

    Checks

    1. 1Check the timeout error of can receive frame egr valve connector and wiring first, then follow the checks listed under E000639.
    2. 2Clear the code and confirm whether E520606 returns on its own.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Develon E520611Timeout error of CAN receive frame Vehicle cut off switch

    Same failure as E000639 on the timeout error of can receive frame vehicle cut off switch, a different part of the same kind as the can communication error.· Lost message
    Check soon

    Causes

    • Fault in the timeout error of can receive frame vehicle cut off switch or its wiring
    • Any cause listed under E000639

    Checks

    1. 1Check the timeout error of can receive frame vehicle cut off switch connector and wiring first, then follow the checks listed under E000639.
    2. 2Clear the code and confirm whether E520611 returns on its own.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Develon E520614Timeout error of CAN receive frame VGT

    Same failure as E000639 on the timeout error of can receive frame vgt, a different part of the same kind as the can communication error.· Lost message
    Check soon

    Causes

    • Fault in the timeout error of can receive frame vgt or its wiring
    • Any cause listed under E000639

    Checks

    1. 1Check the timeout error of can receive frame vgt connector and wiring first, then follow the checks listed under E000639.
    2. 2Clear the code and confirm whether E520614 returns on its own.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

Shared checks

Checks, in order

  1. 1Measure resistance across the CAN pair with power off and compare with the manual value.
  2. 2Check power and ground at each module named in the code.
  3. 3Inspect connectors for water and pushed-back pins along the CAN run.
  4. 4Look for other communication codes to see which module is affected.

Causes

  • Damaged CAN wires or poor connectors
  • Missing CAN termination or a module off the bus
  • Low supply voltage to a module

Most codes here: lost message (13 of 18)

Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

When to stop

You'll notice: Gauges may freeze or show dashes, the engine may run at fixed speed, and the code appears on the monitor.

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.